English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

18/02/2021

 Chrysler Hussain Jaffar (210Pts.)

0

FACTORY ALARM COMES ON

I installed the device on my car 2010 Chrysler Town & Country (Guide # 94291 EVO-CHRT4)

 and the device works fine, but there are two problems:

1-When I start the car with the OEM remote 3x lock, the horn/alarm comes ON.

2-When the engine is turned off from the OEM remote the car dashboard screen and the radio remain on

any thoughts on fixing that??????

 

Note: I only connected T-HARNESS EVO-CHRT4 without any other wires to car

 

Connectez-vous pour répondre Voir 1 réponse(s)

18/02/2021

 Dodge Oleksii Fesenko (230Pts.)

0

2012 Dodge Caravan blue led doesn't flash

2012 Dodge Grand Caravan Stand alone install with CHR4. yellow wire connected but module still doesnt see ignition (no blue led flash) Hardware 7.0 Firmware 59.02 S/N 001A07 219238
Connectez-vous pour répondre Voir 1 réponse(s)

11/02/2021

 Chrysler Hussain Jaffar (210Pts.)

0

Do I have to connect this wire ?

Hi

In Guide # 94291 for 2010 Chrysler Town & Country there is a wire (D1 Yellow/Green (+) IGNITION in 6 PIN CONN) In the drawing it must be connected with Yellow wire in the T-HARNESS EVO-CHRT4 IGNITION BARREL

My question to you is, do I have to connect this wire? because all the people on YouTube have not connected this cable

 

Connectez-vous pour répondre Voir 1 réponse(s)

07/01/2021

 Ram Eric Harper (130Pts.)

0

my update for a 2012 dodge ram shows a 2015 caravan update, why ?

I purchaed a flashlink update modual and a evo-chrt4 for a 2012 dodge ram. When I went to do a firmware update it came up as a 2015 dodge caravan. How do I update the firmware for my vehicle ?
Connectez-vous pour répondre Voir 1 réponse(s)

19/10/2020

 Ram Myung-Jin Jung (160Pts.)

0

EVO-CHRT4

Hello, I'm planning to purchase EVO-CHRT4 for my 2010 RAM 1500 GAS. I have few questions about the EVO product. 1. Is EVO-CHRT4 the correct product for 2010 RAM 1500 GAS? 2. Do I need Flash-Link Updater even if EVO-CHRT4 is preloaded module? 3. My car does NOT have the RAM Fob keyless entry (Standard Key). Is it OK for programing EVO-CHAR4 module? 4. Guide #94291. Is it corrct guide for 2010 RAM 1500 GAS? 5. I'm planning to add-on RFK411 RF kit for EVO-CHRT4. Is it compatable with EVO-CHRT4? Thanks.
Connectez-vous pour répondre Voir 1 réponse(s)

05/08/2020

 Ram Kuya Nads (160Pts.)

1

All LEDs are blinking rather than alternating?

2012 Ram 1500 standard key. after installation and wiring ready for programming, i plugged the data connector I just had all LEDs blinking. the first unit was replaced and i have the 2nd now but still the same, is there a problem on the unit itself or just my vehicle?
Connectez-vous pour répondre Voir 1 réponse(s)

16/07/2020

 Dodge Marcin Pietryga (280Pts.)

0

my activation key has timed out before i could get it installed in my 2015 Dodge Grand Caravan standard key

how can i get it back?
Connectez-vous pour répondre Voir 2 réponse(s)

16/07/2020

 Dodge Marcin Pietryga (280Pts.)

0

my activation key has timed out before i could get it installed in my 2015 Dodge Grand Caravan standard key

how can i get it back?
Connectez-vous pour répondre Voir 2 réponse(s)

02/01/2020

 Dodge Robbie Skipper (130Pts.)

0

the leds do not flash they stay lit???2016 dodge grand carvan

leds on module stays on
Connectez-vous pour répondre Voir 1 réponse(s)

22/12/2019

 Chrysler Andrew Olson (130Pts.)

0

Evo all starts then stops 2 secs the trys again then stops on 2012 t&c van

Car trys to start then stops
Connectez-vous pour répondre Voir 0 réponse(s)

29/11/2019

 Dodge Brett (200Pts.)

0

EVOALL EVO-CHRT4 not programming correctly after installation

Installing an EVO-CHRT 4 in a 2012 Dodge Ram pickup. After initial installation (connection of T-harness), unit does not finish programming procedure correctly. On first attempt during Step 4 of the programming procedure the blue LED remained lit with no flashing after key was turned to ACC and then turned off after turning key to ON/RUN. All lights remained off after turning key to OFF again. Remote start did not work. Repeated steps 1-3 three times with same result on Step 4/5. After reading through help forums, saw the recommendation to reset the unit in case it had been previously programmed for another vehicle. This was done by programming to the red light on step 2 and then holding the program button until all three lights flashed. Now, unit performs normally through Steps 1-3 but now flashes all three lights when turning key to ON, and does so more than three times. The continuity was checked with a voltemeter and there is no loss of power or ground on the 4 pin data connector. This isn't surprising considering this only occurred after resetting the unit. My best guess is the firmware was reset as well, but my understanding is that then the lights should only flash three times. Thank you, Brett
Connectez-vous pour répondre Voir 3 réponse(s)

29/11/2019

 Dodge Brett (200Pts.)

0

EVOALL EVO-CHRT4 not programming correctly after installation

Installing an EVO-CHRT 4 in a 2012 Dodge Ram pickup. After initial installation (connection of T-harness), unit does not finish programming procedure correctly. On first attempt during Step 4 of the programming procedure the blue LED remained lit with no flashing after key was turned to ACC and then turned off after turning key to ON/RUN. All lights remained off after turning key to OFF again. Remote start did not work. Repeated steps 1-3 three times with same result on Step 4/5. After reading through help forums, saw the recommendation to reset the unit in case it had been previously programmed for another vehicle. This was done by programming to the red light on step 2 and then holding the program button until all three lights flashed. Now, unit performs normally through Steps 1-3 but now flashes all three lights when turning key to ON, and does so more than three times. The continuity was checked with a voltemeter and there is no loss of power or ground on the 4 pin data connector. This isn't surprising considering this only occurred after resetting the unit. My best guess is the firmware was reset as well, but my understanding is that then the lights should only flash three times. Thank you, Brett
Connectez-vous pour répondre Voir 3 réponse(s)

29/11/2019

 Dodge Brett (200Pts.)

0

EVOALL EVO-CHRT4 not programming correctly after installation

Installing an EVO-CHRT 4 in a 2012 Dodge Ram pickup. After initial installation (connection of T-harness), unit does not finish programming procedure correctly. On first attempt during Step 4 of the programming procedure the blue LED remained lit with no flashing after key was turned to ACC and then turned off after turning key to ON/RUN. All lights remained off after turning key to OFF again. Remote start did not work. Repeated steps 1-3 three times with same result on Step 4/5. After reading through help forums, saw the recommendation to reset the unit in case it had been previously programmed for another vehicle. This was done by programming to the red light on step 2 and then holding the program button until all three lights flashed. Now, unit performs normally through Steps 1-3 but now flashes all three lights when turning key to ON, and does so more than three times. The continuity was checked with a voltemeter and there is no loss of power or ground on the 4 pin data connector. This isn't surprising considering this only occurred after resetting the unit. My best guess is the firmware was reset as well, but my understanding is that then the lights should only flash three times. Thank you, Brett
Connectez-vous pour répondre Voir 3 réponse(s)

29/11/2019

 Dodge Brett (200Pts.)

0

EVOALL EVO-CHRT4 not programming correctly after installation

Installing an EVO-CHRT 4 in a 2012 Dodge Ram pickup. After initial installation (connection of T-harness), unit does not finish programming procedure correctly. On first attempt during Step 4 of the programming procedure the blue LED remained lit with no flashing after key was turned to ACC and then turned off after turning key to ON/RUN. All lights remained off after turning key to OFF again. Remote start did not work. Repeated steps 1-3 three times with same result on Step 4/5. After reading through help forums, saw the recommendation to reset the unit in case it had been previously programmed for another vehicle. This was done by programming to the red light on step 2 and then holding the program button until all three lights flashed. Now, unit performs normally through Steps 1-3 but now flashes all three lights when turning key to ON, and does so more than three times. The continuity was checked with a voltemeter and there is no loss of power or ground on the 4 pin data connector. This isn't surprising considering this only occurred after resetting the unit. My best guess is the firmware was reset as well, but my understanding is that then the lights should only flash three times. Thank you, Brett
Connectez-vous pour répondre Voir 3 réponse(s)

24/10/2019

 Dodge M S2 (130Pts.)

0

Vehicle won't stay running after the Evo-All start the van, it runs for about 2 seconds. 2011 Dodge Grand caravan

Vehichle won't stay running. I have updated it and used C1 and D1 enabled. If I bypass the key it will stay running but that would be a annoying having to lock the van two times to turn the engine off. I have the hood part installed and the yellow wire hooked up too. The OEM key does everything else I just wanted the remote start.
Connectez-vous pour répondre Voir 1 réponse(s)

16/08/2019

 Dodge Colby Sturrock (130Pts.)

0

Cannot get blue led in 2009 Grand Caravan

I cannot get the programming step. I have the t harness plugged in and the two yellow wires connect together like many tutorials? Is this incorrect? He do not want any other functions other than remote start.
Connectez-vous pour répondre Voir 1 réponse(s)

15/06/2019

 Dodge BHAVIK PATEL (180Pts.)

0

Evo CHRT4 and RF642W

I have installed Evo CHRT4 in my Grand Caravan 2018 with OEM key and it's working great. The CHRT4 was flashed for RF. I am now trying to install RF642W using RFA2A following steps on installation guide. As per the last step on installation guide, I did press & release (-) AND press & release (lock) on RF642w fob, but on CHRT4 it did NOT blink RED and BLUE LED, instead the RED, BLUE, YELLOW LEDs stayed solid on. The fob would sound and show green light [after I press & release (-) and press & release (lock)]. The antenna LED fast blinks (BLUE). I checked wires and everything was good. Can someone help me resolve this? Thank you in advance.
Connectez-vous pour répondre Voir 1 réponse(s)

28/05/2019

 Dodge 2 (130Pts.)

0

Evo CHRT4 and RF642W 2-Way LED

Hi, I just bought Evo CHRT4 and now I am looking to install RF642W 2-Way LED. I wanted to make sure that RF642W 2-Way LED is compatible with EVO CHRT$. Could you please confirm? Thank you. Bhavik
Connectez-vous pour répondre Voir 1 réponse(s)

10/02/2019

 Dodge Ken French (140Pts.)

1

Installed EVO-CHRT4 not working.

Installed this remote starter. Got to the flashing blue light when ignition turned on. Turned ignition off and pressed the lock button. Pressed the lock button 3x and nothing. Tried lock-unlock-lock with same result.
Connectez-vous pour répondre Voir 2 réponse(s)

10/02/2019

 Dodge Ken French (140Pts.)

1

Installed EVO-CHRT4 not working.

Installed this remote starter. Got to the flashing blue light when ignition turned on. Turned ignition off and pressed the lock button. Pressed the lock button 3x and nothing. Tried lock-unlock-lock with same result.
Connectez-vous pour répondre Voir 2 réponse(s)

06/02/2019

 Jeep Jeep Guy (160Pts.)

0

Viper smartstart not communicating with EVO ALL

I've installed a VSM350 in my 2008 Grand Cherokee, following the instructions (splice grey wire with black, plug in connector). The VSM350 has been activated by a local dealer and my viper online account is properly set up. I can update GPS information via the smartstart app (this confirms unit is powered up and communicating with the internet properly). I am not able to lock, unlock, or remote start using the app. When I attempt to lock/unlock or start, I receive the message "unlock failed at [time]" I have enabled H4 via flashlink. I live in a major city and the vehicle is parked outside, the issue is not related to cellular coverage; the app reflects that the vsm350 has 4 or 5 bars of signal strength. I appreciate any suggestions to enable the smartstart to communicate with the evo-all to enable the lock/unlock/remote start. Thank you
Connectez-vous pour répondre Voir 1 réponse(s)

01/02/2019

 Jeep Jeep Guy (160Pts.)

0

Programming EVO-ALL / CHRT4 with SmartStart VSM350

About a month ago, I successfully programmed and installed an EVO ALL with CHRT4 in a 2008 grand cherokee. The 3x lock would successfully initiate a remote start. I recently removed the EVO ALL to reprogram it with flasklink to enable H4 (smartstart). Upon reinstalling EVO ALL, I no longer had blue lights. I reprogrammed to the key and got the blue light to illuminate when clicking lock button. I connected the yellow to the yellow for ignition during initial install and that is still the case now. This yellow wire splice is the only wiring i've done outside of installing the CHRT4 harness. The current issue is that after reinstalling the EVO ALL, I do not get a red light on the EVO ALL after clicking 3x lock. The 3x lock is still enabled in flashlink, in addition to H4 being enabled. EVO ALL was already (and still is) flashed to the latest / best / recommended firmware. Given my inability to remote start with 3x lock before even connecting the smart start, i have left the smart start unplugged until i can resolve the failure to start with 3x lock using the key. I have tried re-flashing the evo-all with latest firmware in flashlink and starting over but am in the same position where i get blue lights but no red, and thus, no remote start using 3x lock. When vehicle is started via the key in ignition, EVO ALL gets a solid a yellow to indicate the evo-all knows it has ignition. My question is: What I'm doing wrong or do I not have connected properly to get my red light back after 3x lock so that the vehicle can start. Does H4 prevent use of 3x lock remote start?
Connectez-vous pour répondre Voir 1 réponse(s)

25/11/2018

 Dodge James Napier (180Pts.)

0

2016 Dodge Grand Caravan Headlight Switch Issues.

I installed the EVO-CHRT4 unit in my 2016 Grand Caravan with no issues, but now my Headlights are always on when the car is running. The Headlight Switch does not work and does not even light up as it should at night. My install was just the T harness with no additional modifications. Never even touched the Headlight Switch. Any idea what's going on? All help is greatly appreciated.
Connectez-vous pour répondre Voir 1 réponse(s)

26/10/2018

 Nissan Ed Pribble (220Pts.)

0

Want to confirm a EVO-ALL that's preloaded with EVO-NIST1 can be flashed with EVO-CHRT4 to work on a 2010 Dodge Charger?

Can a EVO-ALL work for any supported car
Connectez-vous pour répondre Voir 1 réponse(s)

31/08/2018

 Dodge Noe Moran (130Pts.)

0

What to do with d1 yellow wire

Where do I splice in the D1 wire the instruction say to make connection and the other end says cut ignition do I tie in d1 into the yellow wire of the t harness female plug and tape off the other end of it that leads to t harness male plug?
Connectez-vous pour répondre Voir 1 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer