English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

11/01/2025

 Buick Spinner64 (130Pts.)

0

Evo-one 2006 rendezvous no yellow light in programming

Ign on - Blue shuts off red comes on but red does not start flashiing to be able to turn key to start for yellow to come on. When red comes on solid the blue starts flashing but is dim. Red never flashes. Talked to tech support said to try starting when red light comes on instead of waiting for red flashing. Still just does the above. I have Reset, flashed 70.18, started and held in start postion and above repeats. He did say to test purple pin 2 and should be 1.5v. It is .23v and I have seen it fluctuate up to 1.2v while lock/unlock is pressedn etc. I have check every single fuse, put on battery charger, cleaned batt terminal, wiggled wires and still does the above voltage fluctuations. Could it be faulty module? Which I've never had happen in over 15ys of using fortin. Strange the blue light flashes dim after red comes on. Could it be the low voltage on obd pin #2? I've never had on issue with the pk3. Factory radio. No signs of anything aftermarket being installed to disrupt obd2 signal. Obd2 plug in code reader communicates fine and no codes present
Connectez-vous pour répondre Voir 0 réponse(s)

05/01/2025

 Ford Thi Nguyen (190Pts.)

1

2011 Ford E250, stuck on solid Red and Yellow Lights during EVO ONE programing procedure

I finished installing the EVO One on my 2011 Ford E250. Made sure that all the wire were connected correctly based on Guide # 86051. I also installed a relay switch for the parking light the same way as shown in the wiring diagram. I used Flashlink to install the lattest 71.57 Bypass firmware and 1.26 Remote starter firmware. I tried many different troubleshooting steps such as disabled A11 according to the guide and changing the programable output to 2.2 to match the wiring diagram. I also tried older version of firmware to no avail. No matter what I do, it always gets stuck on solid Red and Yellow Lights during step 4 of the the programing procedure when the ignition is turned on. The car I have is regular key without transponder chip. I tried both the 2 keys and DCRYPTOR programing procidure but both has the solid Red and Yellow issue as soon as the ignition is turned on. Please let me know what I am doing wrong and how I can resolve this issue.
Connectez-vous pour répondre Voir 1 réponse(s)

22/12/2024

 FAQ juanfgutil (130Pts.)

0

I am in step 1.evo-one hyundai Tucson 2020

I really need help! I connect the module while pressing th button and only get a red ligh no blie no other light ko blinking. it has been a week trying to solve bit no answer and the instrucctions are soooo confussing. Can somebody PLEASE help me!
Connectez-vous pour répondre Voir 1 réponse(s)

14/12/2024

 Nissan Michael Vasyukhnevich (180Pts.)

0

Red and yellow light flashig alternately after bypass programming.

Evo One with THarn 5? Nissan Frontier 2016It is three harneses: Ignition main one, Immobilizer and OBDII generic. And also installation harnes with white connection.Flashed many times, tryed some options, it goes OK to the end, when i turn the key off red and yellow lights start flashing alternatly. Wires checked many times. Used instalation guide 79451. Evo One SN: 002B04696651. During programming at the step 8 i have flashing rapidly yellow light, but when i turn key into OFF position, red and yellow lights appear flashing alternately. NOW I AM NOT ABLE TO START THE CAR WITH ITS ORIGINAL KEYS.
Connectez-vous pour répondre Voir 1 réponse(s)

10/12/2024

 Audi quin Soe (130Pts.)

0

Step 11 key programing

2016 audi a3 push to start evo all serial number: 001A07 016953 I flashed the correct software on to unit with the flashlink. I get to step 11 of key bypass-program with r-link, and it says to wait up to 5 mins with solid red light. Then it's supposed to flash yellow, and the flah yellow and red, but the red light just stays lit and never goes past that point. I've tried reseting evo reprogramming to a different firmware, then back to the recommended firmware, but I can never get past that point and have waited up to 15mins. What should I do at this point?
Connectez-vous pour répondre Voir 1 réponse(s)

14/11/2024

 Audi optyk07 (150Pts.)

0

2014 Audi Q5 Evo All not flashing yellow in step 8 of Key bypass programming

Im not able to proceed from step 7 in guide 77151. When it should begin to flash yellow and red alternating it just flashes red.
Connectez-vous pour répondre Voir 1 réponse(s)

27/10/2024

 Volkswagen Jung8724 (160Pts.)

0

EVO ALL Stuck in Yellow and Red Light Flashing

Hello, I am installing this on my 2012 VW Tiguan. I followed the process guide 92511. After decryptor and returning the vehicle, yellow and red LEDs flash, instead of staying on like explained on Step 13. Now it says my unit (SN 001A07 559614) has recheaed its limit and I am really stuck. Can you please assist? Thanks, Andrew
Connectez-vous pour répondre Voir 0 réponse(s)

18/08/2024

 Mazda Victor Arkorful (190Pts.)

0

WHY ARE ALL LIGHTS FLASHING AFTER KEY BYPASS PROGRAMMING STATE. INSTEAD OF RED AND YELLOW

I'm trying trying to install the Evo-all (THAR MAZ1) Harness, at the end of the key by-pass programming stage, all 3 lights flash on the module instead of the red and yellow alone. What should I DO.
Connectez-vous pour répondre Voir 1 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer