Questions & Réponses

Ever wonder how your module has been set up? If you have the correct firmware and options for your vehicle?

Did you know you can check all of these things simply by entering the service number on the back of the module in the search bar located on fortin.ca!

Give it a shot the next time you are unsure of how the module has been configured!

I cant remote start the vehicle.
When I push 3x the lock button on the vehicle remote, nothing happen.
I double checked the wires, and all 7 was soldered. I can sent you pictures of the connection that I made.
The programming was made successfully as well. When I plug the six pin cable, the LEDs alternate from blue yellow red and when I release the programming button, the blue LED stay still. Then I connect the others cables and turn the ignition to ON position (without start the engine) so the leds start to flash quickly on red then quickly on blue. That's all.
My vehicle is a Ford Fusion 2014/2015 SE 2.0 with normal start.
Best regards.

Your best bet here is to follow the step-by-step guide available here : EVO-ONE & OEM Remotes

That guide covers basic option setting for 3x Lock Start on Automatic vehicles. If your vehicle is Manual/Standard transmission, you will also have to enable option 33.2. Flash-Link Updater REQUIRED

Quick Run down.

The EVO-ONE has two sets of options. There are options for the remote starter portion while there are also options for the bypass portion of the unit. The remote starter options are used mainly for convenience features such as enabling 3x lock start, alarm functions, cold timers etc... while the bypass options are there to set various DATA / Can-Bus features such as the all important OEM Remote Monitoring.

To toggle between remote starter and bypass options (and firmware updates) via the Flash-Link Manager, you must press the TOGGLE button in the flash-link manager program while the unit is disconnected. There is a text on the bottom right corner that will tell you if you are in Connection Mode : Bypass or Connection Mode : Remote Starter.

While Connection Mode : Remote Starter is active, go to the EVO-ONE Options tab and enable the following option(s).

Option 38.2 - Enable 3x Lock Start (this tells the remote starter that it will be controlled via the oem remote commands detected and then sent via the integrated bypass module) Option 33.2 - Enable this option only if you have a manual transmission vehicle. While here, if the vehicle specific install guide also mentions other required options, please set them now. Don't forget to SAVE OPTIONS.

While Connection Mode : Bypass is active,

First, make sure you have selected and flashed the unit to the latest firmware for your vehicle. You will find the latest firmware under the EVO-ONE Updates tab. Go to EVO-ONE Options Scroll through the options and enable Option C1 - OEM Remote Monitoring (this option allows the bypass portion to actually monitor the oem remotes so that the previous 38.2 option can actually work). Attention! Please leave all the A1-A11 options untouched unless told otherwise. Don't forget to SAVE OPTIONS

I intalled EVO ONE for my Honda accord 2014 standard key and I also installed a compustar G9 RF kit. 

Now, I want to disable the 3X lock remote start. I have tried to disable 38.2 3x lock. The car will not be remote started. But, it will follow the normal remote start precedure to unlock the door and relock it. (In order to disable the factory alarm and security system, the door will be unlocked and relock after engine started).

How can I completely disable the 3X lock remote start functionality. I just want to remain remote start function by click the remote start buttion on compustar remotes( the remote has remote start button).

I cant remote start the vehicle.
When I push 3x the lock button on the vehicle remote, nothing happen.
I double checked the wires, and all 7 was soldered. I can sent you pictures of the connection that I made.
The programming was made successfully as well. When I plug the six pin cable, the LEDs alternate from blue yellow red and when I release the programming button, the blue LED stay still. Then I connect the others cables and turn the ignition to ON position (without start the engine) so the leds start to flash quickly on red then quickly on blue. That's all.
My vehicle is a Ford Fusion 2014/2015 SE 2.0 with normal start.
Best regards.