Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

09/12/2023

 Nissan mobilesolutionsar (280Pts.)

0

Does the lock and unlock wires go into the listed empty slots on a 2019 Nissan Armada using the Evo-Nist1?

The guide says that the lock and unlock wires go into an empty slot.
Login to reply View 1 answer(s)

22/11/2023

 Nissan Ramiro86 (300Pts.)

0

2022 Nissan Rogue remote start push start

I am installing a remote start to a 2022 Nissan Rogue, the installation guide says that 1 key will be sacrificed in the installation and the key in a box, I don't understand what that means, nor about sacrificing the key, nor about the key in the box, I need if someone could help me with that, thank you very much
Login to reply View 1 answer(s)

13/08/2021

 Nissan Ahmed Aboushouk (330Pts.)

0

Nissan Qashqai 2019 Steering Lock Plug wiring

I have successfully installed standalone evo one for nissan qashqai 2019 with push to start When i remote start the vehicle and then enters inside it then when i press the Ignition so i can start diving, car refuses to accept ignition saying steering is locked and doesnot allow car to be on the ON position I have tried enabling door shutdown option and it actually shutdown car when any door is opened So in the current setup , i have to press brake after entering then it shutdowns then i start it normally again I saw something about steering lock plug connector but i donot know which wires in the A plug harrness to connect to ? I have a white/green wire but there is no white/red Please assist me as i want to start driving directly after entering the vehicle
Login to reply View 1 answer(s)

02/12/2020

 Nissan Wesley Bridges (140Pts.)

1

2015 Nissan Altima Ignition Ignition 2 wire

Not a question so much as an update to your notes. On the installation instructions it shows Ignition 2 as Pin 9 Black 24 Pin plug as a Pink wire. Vehicle I had it is not a Pink Wire it is Brown but when tested goes + when PTS is hit for ACC or IGN.
Login to reply View 1 answer(s)

28/07/2020

 Nissan rob Buchanan (130Pts.)

0

Can’t open the doors once vehicle remote started

Hi there, can you please confirm the correct installation and programming sheets for my set up please. 2006 Nissan Pathfinder (Thai made) evo one t harnes 2 stand alone RF 64 2W I have eventually been able to program it, i can remote start with the Orem key and the RF 64,s. However once running I can't operate the doors until I turn off the vehicle.
Login to reply View 1 answer(s)

12/12/2019

 Nissan SPLaudio (180Pts.)

0

2016 VERSA NOTE STD KEY - NO TRANSPONDER, UNABLE TO PROGRAM EVO-ONE

This 2016 Nissan Versa Note doesn't seem to have a transponder. Transpoder connector isn't located at the key cylinder as shown in install diagram. Wired everything up as shown for install diagram, but didn't connect the RX or TX connections as the transponder wires aren't there. I can't get it to program. Getting stuck on the 5th step of programming. The 5th step starts with the yellow LED solid and you turn key to ON/RUN and the red LED should light alongside the yellow. I'm not getting that red LED lit.

I went into the settings and turned off the transponder for the Evo-One but still having the same issues. Super basic install. Any help would be much appreciated.

Login to reply View 2 answer(s)

12/12/2019

 Nissan SPLaudio (180Pts.)

0

2016 VERSA NOTE STD KEY - NO TRANSPONDER, UNABLE TO PROGRAM EVO-ONE

This 2016 Nissan Versa Note doesn't seem to have a transponder. Transpoder connector isn't located at the key cylinder as shown in install diagram. Wired everything up as shown for install diagram, but didn't connect the RX or TX connections as the transponder wires aren't there. I can't get it to program. Getting stuck on the 5th step of programming. The 5th step starts with the yellow LED solid and you turn key to ON/RUN and the red LED should light alongside the yellow. I'm not getting that red LED lit.

I went into the settings and turned off the transponder for the Evo-One but still having the same issues. Super basic install. Any help would be much appreciated.

Login to reply View 2 answer(s)

23/11/2019

 Nissan SALEH QAWASMEH (180Pts.)

0

Evo all - Nissan Altima 2010 PTS THAR-NIS1

After finishing all the programming steps red and yellow lights ON and OFF 3x Nothing happened
Login to reply View 2 answer(s)

23/11/2019

 Nissan SALEH QAWASMEH (180Pts.)

0

Evo all - Nissan Altima 2010 PTS THAR-NIS1

After finishing all the programming steps red and yellow lights ON and OFF 3x Nothing happened
Login to reply View 2 answer(s)

28/10/2019

 Nissan Justin Stroud (270Pts.)

0

2018 Nissan Frontier Guide # 72031 - parking lights and horn, and lock/unlock

Successfully installed an Evo One with THAR-ONE-NIS2 and remote start is working. In the guide, it points to the hill assist button to tap into the parking lights, I do not have that button, and I could not find the plug near there to tap into it. Is there another option? I also have no horn when arming / disarming / starting. The guide doesn't mention one, is it possible to have this? Locking with the remote works, but unlocking can usually takes hitting the button twice. Is this normal, or do I need to triple check my connections? I ran the purple and purple-white wires to the lock/unlock wires in the driver side kick panel.
Login to reply View 1 answer(s)

15/01/2018

 Nissan Brian Laroche (140Pts.)

1

2011 Altima PTS 'No Key' on Instrument Cluster

    2011 Altima Push-To-Start Using T-harness.  Connected to OBDII, Brake Pedal, Keybox.  Tapped into Brown wire on push-to-start button. A1-A11, C1, D1, D1.2, D3 Enabled Latest firmware for flasher and EVO-ALL

Went through programming sequence (with battery out of FOB).  Sequence completed sucessfully ending with rapid-flashing yellow light.  When activated with FOB inside vehicle, it starts fine with the 3x lock press.  With FOB removed from vehicle, 3x lock press does not start vehicle.  Vehicle displays "No key" message on instrument cluster.  

I have tried to re-flash and re-program the EVO-ALL multiple times, all with identical results.  

What am I missing here?

Login to reply View 1 answer(s)

15/01/2018

 Nissan Brian Laroche (140Pts.)

1

2011 Altima PTS 'No Key' on Instrument Cluster

    2011 Altima Push-To-Start Using T-harness.  Connected to OBDII, Brake Pedal, Keybox.  Tapped into Brown wire on push-to-start button. A1-A11, C1, D1, D1.2, D3 Enabled Latest firmware for flasher and EVO-ALL

Went through programming sequence (with battery out of FOB).  Sequence completed sucessfully ending with rapid-flashing yellow light.  When activated with FOB inside vehicle, it starts fine with the 3x lock press.  With FOB removed from vehicle, 3x lock press does not start vehicle.  Vehicle displays "No key" message on instrument cluster.  

I have tried to re-flash and re-program the EVO-ALL multiple times, all with identical results.  

What am I missing here?

Login to reply View 1 answer(s)

06/12/2018

 Nissan Michael Charleton (130Pts.)

0

Installed evo all on 2014 maxima after successfully programming yellow and red led's alternate flashing .

001a06820753 hardware vr.6 firmware vr.72.19 pre loaded
Login to reply View 1 answer(s)