Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

29/01/2024

 Dodge ffbuddyhughes (190Pts.)

0

no blue lights when programming oem key

programmed and wired correct, no blue lights comes on during final step of turning ignition on with oem key 2008 dodge ram 2500 diesel
Login to reply View 0 answer(s)

09/11/2021

 Dodge Shane Benjie (220Pts.)

0

Solid blue light...HELP!

2010 Dodge Journey- installing the evo all as a stand alone starter, updated to firmware 74.39 and using a T-harness CHR4. i've connected both yellow wires and cut the yellow wire and attached the yellow/green wire on the ignition side as per the diagram. I've checked the connection several times but each time I only get the solid blue light when programming, what am i doing wrong?
Login to reply View 1 answer(s)

30/10/2020

 Dodge AndrewA (180Pts.)

0

Red Light flashes 6 times and won't start

07 Durango, Evo All standalone with T-Harness, was working perfectly fine using 3x lock on OEM remote, or using a compustar remote that came programmed when I bought the vehicle. Blue light activates when locking or unlocking, orange light activates when ignition is turned on, battery hasn't been disconnected at all, power is fine, ground is fine, resistor from brown/white to parking lamps is fine, new battery in remotes, tested the hoodpin, I've pulled it entirely apart and checked all of the connections, and yet it blinks the red light 6 times, as well as the parking lamps and headlights, which I find extremely odd considering the troubleshooting only goes 1-5 flashes. Spent 2 days trying to sort it out and I've come up with nothing, any help or guidance would be appreciated.
Login to reply View 1 answer(s)

01/09/2020

 Dodge John Flynn (160Pts.)

0

2016 Dodge Challenger, EVO-ALL w/ CHR6, now throwing U0415 Check Engine Light

As Title indicates, post installation the client is getting a CEL U0415. It happened to me after programming but I cleared it and figured it was a fluke. According to him, per his Dodge dealer, they have seen this happen with aftermarket remotes starts and also stereos on the Challenger. Any suggestions other than rolling back firmware? When tapping for 12V ignition I grabbed the incorrect wire first time around. It was pink/wht but didn't give 12V with IGN. The snake shows Pin 27 OR 31 at BCM, plug E. 27 was the wrong one, 31 was hardly pink/wht, more pink/yel but did give 12V with ignition.
Login to reply View 1 answer(s)

14/12/2019

 Dodge Matthew Coldwell (160Pts.)

0

while programming, blue light goes off at key on

installing standalone evo all (EVO-CHART5) with T harness on 2007 dodge durango. I have made the connections purple from T to Green/ Red (a18), yellow from T to yellow(a1), plugged T harness behind key switch. Used flash link 2 and selected options c1 for lock 3 times to start. I plug in black plug to evo all while holding in the button and release on blue, plug all connectors in and when i turn the key on the blue light goes off. I have 12vdc on the yellow wire (a1). Turn the key off and blue light comes back on. I have verified my all my connections. I even did a master reset, downloaded the latest firmware etc. what else should i do?? I have installed 4 of these so far and i have never had this issue with the others.
Login to reply View 1 answer(s)

12/12/2019

 Dodge Anwar Hussein (130Pts.)

0

Evo installation module keeps flashing blue,red and yellow LED lights while programming.No solid blue LED light.

Evo installation module keeps flashing blue,red and yellow LED lights while programming.No solid blue LED light. Installing evo module on dodge journey 2010.The blue, red and yellow LED lights keeps on flashing and does'nt stop. Might need flash link, please help!!
Login to reply View 1 answer(s)

09/12/2019

 Dodge Jonathan Mercado (130Pts.)

0

2014 durango evo all. T harness stand alone is programmed but wont start.

Connected ignition wire to the red green wire in driver side kicker panel as shown in install video. All lights on evo all work when hitting lock 3xs.
Login to reply View 1 answer(s)

14/11/2019

 Dodge Mustafa Abbasi (200Pts.)

0

2011 Journey doesn't start - Red light flashes 5 times for hood open error

I am installing a EVO-CHRT6 on a 2011 Dodge Journey. I connected all the wires except for the parking lights. I programmed the module according to the guide with the C1, D1, and D1.10 options. However on trying the 3x lock to remote start the module just flashes red 5 times. I have tried reprogramming the module but the problem persists. I have also made sure the hood pin wire is not grounded. The vehicle does not have a factory hood pin. Please let me know how to solve this issue, I have never encountered anything like this before
Login to reply View 1 answer(s)

17/11/2019

 Dodge Reva Smith (130Pts.)

0

Evo-CHR6 Programing Issue

The module is not currently cycling through the various leds. The module lights up red, yellow, and blue but will not go to the all yellow for programing steps. The wiring currently hooked up is Can Low, Can High, T-Harness, Ignition, and parking lights. The kit included a valet switch and hood pin which I did not install. Does this need to be hooked up? Please help.
Login to reply View 1 answer(s)

28/10/2019

 Dodge Justin Stroud (270Pts.)

0

2018 Dodge Journey - Evo ALL THAR-CHR6 - Guide # 73591 - CAN H and CAN L alternate location?

The guide states that the CANH and CANL wires are up in the CAN junction block. I've located the wires, and I can just get the plug out but once I do, there is not enough wire slack to be able to splice into them. I've seen people mention thay've gotten this to work, but I do not see how. I know that there is a CANH and CANL in the OBD2 port, as they are there in pretty much all vehicles since it's an industry standard. Is there any reason I cannot splice into those?
Login to reply View 1 answer(s)

07/07/2019

 Dodge Jeffrey Coleman (140Pts.)

0

'16 Dart Evo All Standalone stopped working

I installed the Evo All with T harness in my 16' Dodge Dart last year before winter. Install was done correctly, and the unit worked flawlessly all winter without any issue. I went to use it on a hot day to cool down the car, hit Lock X3, and nothing... Looked into it today, and the blue light flashes with input, the Red light comes on and clicks indicating its starting the process, then the Yellow light comes on also for a period of time, with nothing happening... I even reset the unit and reprogramed all over. I get it back in, and the same results... the car will not start remotely. Any help?? I love this unit, but not right now!
Login to reply View 0 answer(s)

29/12/2018

 Dodge Matthew Fudgeoff (130Pts.)

0

Evo and t harness starts by itself

2005 dodge magnum, evo with chrt5 harness, the two days with the remote starter were flawless, now the 3rd day the car it starting itself all the time, without pressing the remote or with just one press to lock the door will also start it. Wiring verified, connections soldered and heat shrunk.
Login to reply View 0 answer(s)

21/12/2018

 Dodge tom lee (210Pts.)

0

Dodge Dakota 2008 doesn't Start** CHR5

EVO-All.....reprogrammed Evo-All with Flash Updater....Went smoothly....C1 and D1 enanled along with 3x Lock....Connected Yellow fromT-Harness with yellow wire of 20 pin connector...Mauve wire from T-Harness to green-red wire of 20 pin connector....Programming in truck went smoothly...After flashing Blue Leds, hit Lock on OEM remote got a Beep and flashing Blue leds went off...Tried to 3x Remote start Blue LED went on with each press, but engine did not start....Tried Lock-unlock-Lock but still no response. When started with key , Yellow Led is on!! Master reset and tried again , no response...Each time I attached the T-Harness I had to reset the Clock...What am I doing WRONG?

Login to reply View 1 answer(s)

05/12/2018

 Dodge BRANDON PUNZALAN (410Pts.)

0

Dcryptor Does not complete

I have made it to step 15 and keep getting stuck on the dcryptor process. I have started from step 1 multiple times and successfully made it to step 15. I have tried flashing the firmware and I am unable to get it to complete the dcryptor process. I have confirmed door unlock and slow blue light before rdisconnecting evo all and starting decryptor.
Login to reply View 1 answer(s)

11/06/2018

 Dodge skylinewindowtinting (600Pts.)

0

2012 Dodge avenger no start

Stand alone unit was installed 2 years ago. Now it can't start with the key What could go wrong it plug and play.
Login to reply View 1 answer(s)

26/07/2017

 Dodge joe schiavone (140Pts.)

1

After programming my car states in the menu program NOT IN PARK.

My Evo All is programmed for my Dodge Journey 2016, but when I get in the car I can take off but it comes up with an error message that the car is not in park. If I put the car back in park and then in drive it will go away. Please advise if there is a fix for this. Thanks, Joe
Login to reply View 1 answer(s)

04/03/2017

 Dodge Charles Jones (130Pts.)

0

Problem programing 2012 ram

I am installing in stand alone mode but when it comes to programing ignition when I turn the key to the run position blue light flash rapidly, when I turn to off position it continues to flash rapidly when I hit lock button on remote blue light keep flashing but slower.
Login to reply View 2 answer(s)

04/03/2017

 Dodge Charles Jones (130Pts.)

0

Problem programing 2012 ram

I am installing in stand alone mode but when it comes to programing ignition when I turn the key to the run position blue light flash rapidly, when I turn to off position it continues to flash rapidly when I hit lock button on remote blue light keep flashing but slower.
Login to reply View 2 answer(s)

26/12/2016

 Dodge Aaron Jackson (130Pts.)

0

Check Engine Light CHRT5 Charger

2007 Dodge Charger R/T, After flashing suggested firmware and selecting correct options I can get the car to start for a few seconds then it dies. I got some check engine codes refferring to loss of data/connection to gear shifter, fuel gauge, and such. Check engine light will cause this I know. Cleared codes and still the same results. No CEL prior to install. Using as stand alone remote starter. No aftermarket starter or alarm. Codes are : U0103 U110f U110e U1411 U110c U1403 Ive searched through forums and faqs for days with no progress. Help please!
Login to reply View 1 answer(s)

05/12/2016

 Dodge Scott Roberts2 (180Pts.)

0

Wont program. No flashing blue light

I can't get my CHRT5 to work. I connected the 2 yellow ignition wires, and the green/red to purple for the MUX. Apparently this is all I need to do. Others on a Ram forum did this and got it to work. I'm thinking it might have to do with the programming with the module. The guy I bought it off of updated it for me, and turned on the 3x lock function. When I hold down the button and plug the data cable, I leave it on the blue light. I then plug everything in. Turn the key to on, and the blue light turns off. Then my dash lights flicker, and I get a check gauges light. Please help.
Login to reply View 1 answer(s)

05/12/2016

 Dodge Scott Roberts2 (180Pts.)

0

Wont program. No flashing blue light

I can't get my CHRT5 to work. I connected the 2 yellow ignition wires, and the green/red to purple for the MUX. Apparently this is all I need to do. Others on a Ram forum did this and got it to work. I'm thinking it might have to do with the programming with the module. The guy I bought it off of updated it for me, and turned on the 3x lock function. When I hold down the button and plug the data cable, I leave it on the blue light. I then plug everything in. Turn the key to on, and the blue light turns off. Then my dash lights flicker, and I get a check gauges light. Please help.
Login to reply View 1 answer(s)

03/11/2016

 Dodge Ivan De Dios2 (130Pts.)

0

My grand caravan 2015 sensor Gate on and all the lights on after the installation of evo-all

After the installation of the Evo-All CHRT4, my Dodge Caravan 2015 have the GATE indicator on on the dashboard and all the internal lights on too. What can I do?
Login to reply View 2 answer(s)

03/11/2016

 Dodge Ivan De Dios2 (130Pts.)

0

My grand caravan 2015 sensor Gate on and all the lights on after the installation of evo-all

After the installation of the Evo-All CHRT4, my Dodge Caravan 2015 have the GATE indicator on on the dashboard and all the internal lights on too. What can I do?
Login to reply View 2 answer(s)

01/09/2016

 Dodge William Thomason (130Pts.)

0

Blue LED does not flash 2014 Dodge Charger SE Step 10 turns off when PTS pushed Can Hi/Lo OK...Brake?

I have been through the programming steps 3 times. Was somewhat confused as to whether I should push on the brake (as in "hold down brake and push button to start" for normal starting) during programming steps so I tried both ways. Both times, all goes well until step 10 of the programming sequence. With the Blue LED on solid, when pushing the start button once to turn on the ignition, the blue LED turns completely off and does not flash. I read elsewhere in the Dodge FAQ where it was suggested to connect red/green A18 wire to brake pedal wire, but in my install guide (#12211 - Stand Alone for CHRT6 with T Harness for Automatic Trans Only), the connection diagram says to connect wire A18 to the parking light switch wire which is how I have it. Just to note, when I do not press the brake pedal during programming, the car goes to run position, but does not actually start whereas when I do press the pedal, it does. This seems to have no effect either way on the situation with Blue LED (behavior is same either way). I have double checked and can-bus hi/lo wires are correct and not reversed. Hardware version is 6, firmware is 74.25. Thanks for any advice you may have!
Login to reply View 1 answer(s)

20/05/2016

 Dodge florencio ramirez2 (280Pts.)

1

blue ligth blink but after the yellow ligth come up.

Installed the EVO-CHRT4 on a 2011 DODGE CHALLENGER and the car will not remote start with factory remote pressing the lock 3x. I am using this is a standalone. I sucessfully programmed the unit as per the PDF. When I press lock I see the blue LED flash on the EVO-ALL. I made all the neccessary connections except I did not connect the hood pin as they are said to be optional. Everything seems to be set up correctly. Why won't the car remote start? Another question is there a difference between the intelligent key and the push to start? I have an PUSH TO START . I have tried programming the EVO-ALL with the same results. AND A yellow ligth come steady afer i turn the car off and i push the start again. Thanks.
Login to reply View 3 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue