Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

18/11/2023

 Dodge Dallas Fischer (130Pts.)

0

2015 Dodge Charger will not remote start

Hello. Referring to this guide I have set up my EVO-ALL

Here is what I have done:
- Flashed the unit with the latest firmware
- Selected my vehicle in the flashlink software
- Connected the T harness and ignition wires

When programming:
- Let go of programming button on BLUE
- Press programming button once to turn off BLUE
- Turn ignition to RUN
Now the BLUE led starts flashing. According to the guide, the RED led should also be flashing, which it is not. That leads me to believe that CAN2 is not being detected, is that correct? How do I fix this issue?

Login to reply View 1 answer(s)

29/11/2022

 Dodge Omar Hasan (190Pts.)

0

Change Connection location of CAN high and CAN low

Is it ok to change the location of connection for the CAN high and CAN low wires from where I should connect them as shown in the guide to the OBD II
Login to reply View 1 answer(s)

01/11/2022

 Dodge Sun Chong (130Pts.)

0

Intermittently will not shut off when time up.

2015 Dodge Journey.Push to start. Evo-all.Hardware ver 7.0 Firmware 69.06. S/N: 001A07 215167 Standalone installation, lock X3 to remote start . Sometimes the engine stays running when timer is up. Parking lights turned off, but engine still running. Tried remote start again, will not shut engine off. What could it be? Software issue?
Login to reply View 1 answer(s)

17/12/2020

 Dodge Keith burling (160Pts.)

0

Temperature settings 2013 dodge journey

Installed the evo start 2 and when i use phone to start the dodge journey the temperature is set to cold. How do you program it so it will turn on the heat and quit resetting the vehicle to ac? I cant find any options for it on the programmer
Login to reply View 1 answer(s)

23/09/2020

 Dodge Tom Schneider (500Pts.)

0

Installation help

I am about to install the Evo All in a 2018 Dodge Journey PTS and i'm just wondering what is the point in connecting the yellow/red(d3) and yellow/green(d1) together on the 6 red connector in the installation instructions? Is it a must or is it not necessary? Thank
Login to reply View 1 answer(s)

10/06/2020

 Dodge Christopher Thomas (130Pts.)

0

I can not find the pink and white ignition wire (9 v)?

I have a 2018 dodge challenger v6 push button start and this is the only wire I can find.
Login to reply View 0 answer(s)

14/05/2020

 Dodge Michael jones2 (130Pts.)

0

I cannot get through step 5 to 6. On the blue light is solid and I press the program button the light just turns off.

When working on steps five through six I get the solid blue light I press the ignition button twice then the program button and the light turns off and does not come back on. This is on a 2013 Dodge Journey push to start.
Login to reply View 1 answer(s)

16/12/2019

 Dodge Orlon Rose (130Pts.)

0

EVO-ALL 2016 DODGE JOURNEY SHUTS OFF WHEN I OPEN DOOR SOMETIMES

INSTALLED EVO-ALL IN 2016 DODGE JOURNEY, INSTALLATION AND PROGRAMMING WENT SMOOTHLY. SOMETIMES AFTER REMOTE START IT WILL SHUT OFF WHEN I OPEN THE DOOR AND SOMETIMES NOT. THE LAST TIME AFTER I OPENED THE DOOR AND IT SHUT DOWN I GOT IN, TURNED IT BACK ON VIA THE FACTORY PUSH-TO-START BUTTON, DROVE HOME, AND WHEN I PARKED AND OPENED THE DOOR TO GET OUT IT SHUT OFF. WHATS GOING ON WITH THIS SYSTEM, IS IT NOT COMPATIBLE WITH MY JOURNEY.
Login to reply View 1 answer(s)

09/12/2019

 Dodge Jonathan Mercado (130Pts.)

0

2014 durango evo all. T harness stand alone is programmed but wont start.

Connected ignition wire to the red green wire in driver side kicker panel as shown in install video. All lights on evo all work when hitting lock 3xs.
Login to reply View 1 answer(s)

17/11/2019

 Dodge Reva Smith (130Pts.)

0

Evo-CHR6 Programing Issue

The module is not currently cycling through the various leds. The module lights up red, yellow, and blue but will not go to the all yellow for programing steps. The wiring currently hooked up is Can Low, Can High, T-Harness, Ignition, and parking lights. The kit included a valet switch and hood pin which I did not install. Does this need to be hooked up? Please help.
Login to reply View 1 answer(s)

28/10/2019

 Dodge Justin Stroud (270Pts.)

0

2018 Dodge Journey - Evo ALL THAR-CHR6 - Guide # 73591 - CAN H and CAN L alternate location?

The guide states that the CANH and CANL wires are up in the CAN junction block. I've located the wires, and I can just get the plug out but once I do, there is not enough wire slack to be able to splice into them. I've seen people mention thay've gotten this to work, but I do not see how. I know that there is a CANH and CANL in the OBD2 port, as they are there in pretty much all vehicles since it's an industry standard. Is there any reason I cannot splice into those?
Login to reply View 1 answer(s)

19/10/2019

 Dodge Justin Stroud (270Pts.)

0

2018 DODGE JOURNEY Unable to find pink/white 9v ignition wire.. GUIDE #73591

Going through the guide, I have removed the driver side kickpanel and there is a huge bundle of wires, and I've looked through them and found two pink/wire wires, niether of which are 9v. One is .05v the other 12v. Am I just missing it?

 

:EDIT: I dont know why the pictures wont show up, they appear fine when creating the post and if I make them any smaller, they'll be hard to see.

Login to reply View 1 answer(s)

19/10/2019

 Dodge Justin Stroud (270Pts.)

0

2018 Dodge Journey Can high and can low location. Guide #73591

I see that there are can bus connection at the junction block per the pictures on the guide and from wire colors, but I cannot see for sure which are the white green and white blue connections. Is it possible for me to access these from the obd2 Port? I'm using the thar-chr6 harness. I see that pin 6 is can high, and pin 14 is low. Is it possible to use these? On the obd2 Port I mean.

 

:EDIT:

There are no white/green and white/blue wires where the guide says they are. I'm at a standstill until I can figure this out.

The guide might need a rivision, I also cannot find a pink/white ignition wire behind the driver side kickpanel. The two I found are .05v and 12v, nothing I can find is 9v.

Login to reply View 1 answer(s)

11/04/2019

 Dodge GESSLER SOBALVARRO2 (130Pts.)

0

2018 Dodge journey, on programming procedure step 6 the light will not change from yellow to red, all wire are good

On a 2018 Dodge Journey, I can not get an evo all to work. on the programming procedurs step 6 the light will not change from yellow to red, check all the wires, flash the module with the flasher and put the firmware 74.32, didn't work, the programmer was suggesting the firmware 74.18, try it didn't work. Updated the flasher and flash all the firmare again and didn't work. I check all the wires one by one and they were good. Need help please
Login to reply View 1 answer(s)

05/11/2018

 Dodge Shawn Stubnar (130Pts.)

0

Will this work with an existing aftermarket alarm

Hello I have a 2018 Durango it has a aftermarket alarm from the dealer and I wanted to make sure this will work with it
Login to reply View 1 answer(s)

12/08/2018

 Dodge Tom Schneider (500Pts.)

0

Will I still need to tap into the ignition starter wire?

Not sure if I still need to tap into starter wire or just connect the T-Harness.
Login to reply View 1 answer(s)

19/12/2017

 Dodge Edward Cansler (280Pts.)

0

what is color of starter wire from push button to starter

2013 dodge charger push to start what color is wire from push button to starter
Login to reply View 0 answer(s)

19/12/2017

 Dodge Edward Cansler (280Pts.)

0

what color is the starte wire from the push button to starter

what color is the wire from the start push button to the starter
Login to reply View 1 answer(s)

26/07/2017

 Dodge joe schiavone (140Pts.)

1

After programming my car states in the menu program NOT IN PARK.

My Evo All is programmed for my Dodge Journey 2016, but when I get in the car I can take off but it comes up with an error message that the car is not in park. If I put the car back in park and then in drive it will go away. Please advise if there is a fix for this. Thanks, Joe
Login to reply View 1 answer(s)

12/02/2017

 Dodge jamfit (130Pts.)

0

2015 dodge challenger pts chrt6 ultrastart remote starter shuts off after roughly 15 seconds

ultra start remote starter with evochryt6 on a 2105 dodge challenger pts everything works great but it will only run approximately 15 seconds shuts off and does not attempt to restart..I have tried 74.30 as well as 74.28 and there is no difference
Login to reply View 1 answer(s)

19/01/2017

 Dodge Daryl McKillop (440Pts.)

0

2014 Dodge Dart Push Start

I have a buddy who wants a remote start in his 2014 dodge dart, manual transmission, push button start. Install guide #14141 is everything I need with the exception that it shows only the Tip-Key. Does this guide still work for push start models or is there another install guide I'm not seeing?
Login to reply View 1 answer(s)

08/01/2017

 Dodge bryan gage (130Pts.)

0

the car wont shut off after connecting parking lights had to unplug the evo now nothing works

can the unit be reset or is it gone bad now no remote start or alarm
Login to reply View 1 answer(s)

20/05/2016

 Dodge florencio ramirez2 (280Pts.)

1

blue ligth blink but after the yellow ligth come up.

Installed the EVO-CHRT4 on a 2011 DODGE CHALLENGER and the car will not remote start with factory remote pressing the lock 3x. I am using this is a standalone. I sucessfully programmed the unit as per the PDF. When I press lock I see the blue LED flash on the EVO-ALL. I made all the neccessary connections except I did not connect the hood pin as they are said to be optional. Everything seems to be set up correctly. Why won't the car remote start? Another question is there a difference between the intelligent key and the push to start? I have an PUSH TO START . I have tried programming the EVO-ALL with the same results. AND A yellow ligth come steady afer i turn the car off and i push the start again. Thanks.
Login to reply View 3 answer(s)

29/10/2014

 Dodge Gavin CHING (420Pts.)

0

is there any way i can change this? i would like it to chirp when unlocking the door on first unlock press

2014 charger PTS
Login to reply View 1 answer(s)

29/10/2014

 Dodge Gavin CHING (420Pts.)

0

Possible to turn off chirp every time door handle is grabbed/ lock button on door is pressed

2014 charger pts viper 3606
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue