Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question

0

EVO ALL GUIDE #105331 - Confusing Language

Installing stand-alone on a 2020 Nissan Frontier PTS. The Frontier has a factory hood switch for alarm functions. The config / options section of the guide states to set A11 to OFF if no hood pin. Does this imply to set A11 to ON in this circumstance? And I assume the blue hood pin wire is moot in this situation, or does it require grounding as the full diagram illustrates? A little confused on the intent.

0

2022 Nissan Rogue remote start push start

I am installing a remote start to a 2022 Nissan Rogue, the installation guide says that 1 key will be sacrificed in the installation and the key in a box, I don't understand what that means, nor about sacrificing the key, nor about the key in the box, I need if someone could help me with that, thank you very much

14/10/2023

Nissan G M (16110Pts.)

0

2010 nissan patrol

Hello. For a 2010 Nissan Patrol (Euro), which instructions will work? And the firmware? StandAlone.

20/01/2023

Nissan XainK (130Pts.)

0

Brakes light up when remote starting but the 2010 Hybrid Altima does not start

This is a weird one, because the car remote starts pretty much every other remote start session. I'm not sure what's causing that as I checked the wiring and it doesnt seem like anything is wrong. So here it goes, when i try to remote start the car from far I see my brake lights turn on* (as in the brakes are being pressed) but the car does not start. the problem is mainly that the brake lights STAY ON unless I actually go to the car and start it myself, however even when i get to the car nothing pretty much works. I press the brakes myself and when I press the the push to start button it stays on lock (it goes LOCK-ACC-ON) so i pretty much freak out, unlock and lock mulitple times, press and depress the brake while keep hitting the push to start untill it goes off and then I manually start it. INFO: 2010 Hybrid Altima (Push to start) EVO-ALL using RL1 red connector in the module * passanger side brake light does not LIGHT UP, the bulb itself works only when i run the headlights but not when i press the brakes

0

After dcrypting and back to the car, the red and yellow light keep flashing.. why is that????

2014 Nissan Juke, push button,

0

Fuse rating for EVO-ALL power supply

I am about to install EVO-ALL for Standalone installation ( without the T-Harness ) for a nissan Qashqai ( Rogue sport in CA ) with push to start ( Guide # 83931 )

S/N of my EVO-All is : 001A07026604

I have three main questions so i can complete the installation :

1- Fuse rating for the power supply of the module ( between B4 pin and 12v battery )

2- Diodes direction is confusing me as the Ignition A4 pin is an output pin which means that Current should flow from EVOALL to the car BCM pins while the Diodes direction says the opposite  ( cathode at top meaning current flows from BCM pins to EVOALL )

3- Which is more recommended for a way of control to disable remote starting when needed ( i cannot have Alarm functions beside remote starting for this vehcile ) where 2nd option would completey shut off the power to EVOALL :

- Adding ON/OFF switch on the Hood Pin A8( connecting other switch end to ground )

- Adding ON/OFF switch on B4 pin on the same line of the Fuse ( connecting other switch end to ground )

  Many thanks in advance for your support & cooperation

0

2021 Nissan Frontier evo-nist4 wont work.

Module hooked up and programed correctly, do 3x lock, blue blinks every push, then orange and red come on, red shutsoff and orange stays on. No start.

0

2013 sentra push to start fix is to connect white/black wire from where to which wire exactly?

I read a previous post about a nissan being wired with pre-assembled harness and EVO-ALL on 2013 push to start sentra ... and brake lights and start button light up but nothing starts...The red light on controller flashes 3 times after it tries to start.The fix was connecting the white/black wire from 19 pin connector to push to start button..I just need some guidance as to where exaclty does the white/black wire come from and where exactly am I supposed to connect it? I`m not a tech,just a guy who bought a plug and play remote start on ebay.Any help is appreciated..

0

Nissan Sentra remote start not working.

I have a 2017 Nissan Sentra PTS. I've done the programming and decrypting processes twice now and pressing the button 3 times to start does not work. The security and caution light on the dash are also on. The service number on the program module is 00A07336089. I just rechecked the ground and now the caution light has turned off, nut the security light is staying on.

0

I can not get the blue light to flash on the module on the first step of programming

0

Unable to sample the vehicle immobilizer data

2014 Nissan Sentra PTS After inital programming and then attaching module to my PC and running the FlashLink Manager I received the message "The module was not able to sample the vehicle immobilizer data. Reconnect the module to the vehicle and follow the programming instructions from STEP 1 to sample the immobilizer data. I can't follow step one if all I get is a red light as soon as I plug in the module. The instructions state to hold the button on the box and release when you get a yellow light. So, I am stuck. I re-flashed the firmware and it did nothing.

0

Nissan rogue 2021

Bonjour, j'ai installé dans un nissan rogue 2021 push un EvoOne avec l'application Cellulaire MS3G et mon client m'avise que le démarreur ne fonctionne presque jamais et que lorsqu'il fonctionne il à rarement une confirmation de retour. J'ai utilisé la sortie inition auxiliaire du EVOONE comme indiqué sur le plan Est-ce que j'aurais due allé me branché sur un inition directement dans la voiture?

0

Which circuits on the evo one are used to interrupt the brown clutch switch

fed the brown wire at the white clutch switch 12v so I'm good there now I must interrupt the grey wire at the brown clutch switch for cranking and need to know which circuits on the EVO ONE are used to achieve this 2011 Nissan Juke Push to Start, Manual Trans