Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

05/12/2022

 Ford Gene B (130Pts.)

0

Differentiate between fob and door keypad on ford / lincoln

Is there an option I can activate to tell my Evo All to ignore the input from the door keypad? I would like the fob to be the only option when remote starting the car. Should this not be possible, is there anyway the system can be changed from starting with Lock being pressed three times to starting with Unlock, followed by two lock combination.
Login to reply View 1 answer(s)

30/08/2020

 Chevrolet David Brehmer (130Pts.)

0

2020 Colorado RF Kit disrupts Daytime Running Lights

I have a suuccessful installation. Everything works: remote start, lock/unlock, with the OEM key fob (x3 lock remote start) and the RF442 Kit. The only isssue is that when the RF442 is used to either unlock or remote start the vehicle, the DRL's do not function as OEM intended. The DRL's are the low beams with low poer output. With the OEM remote, everything act's normal, however, with the RF Kit, the low beams simply turn on to full brightness (not low power like it should). I have set the parking lights control in the firmware to both on and off, both with the same issue. In addition, the RF Kit does not 'flash' the vehicle lights to confirm lock or unlock and does not turn on parking lights to indicat the vehicle is running (under remote start conditions).
Login to reply View 1 answer(s)

21/11/2018

 Kia Eric Wallace (240Pts.)

0

2014 Kia Forte EX PTS VIN8 A Couple of Questions

1st I used Guide 24661 for Evo ONE and 68731 for FL4 when installing the EVO One (recommended firmware identified on program screen, its higher than 76.36, i think there are two newer firms but it wont let me click on them, one is a beta ver.) in car to include adding 2-1 amp diodes at PTS. The car is loaded with options, heated front rear, ac front driver seat, nav and tech pack and more. So I connected laptop to FL(ver 4.05 and recomended in program screen) and FL4 to bypass/ RS and logged in, I dont see the toggle in the lower right corner they speak of, instead I can just click on the tab at top of screen and it asks to confirm or cancel(if you changed anything and didnt save) to switch between bypass and RS. Right now 3x locks the car will crank over but no run, my seat moves, Headlights and dash light up, air controls work, and radio comes on then I hear a couple clicks then the car starts to crank but acks like no fuel, What are all the settings I should have on in the bypass and starter options? I think I had to choose 2.4 in order to get it to even crank, What am i missing or need to check 2nd I see the bypass/starter has a programming set of intructions and the FL4 has its own programming setup however when save and loading setup in user interface when all devices are connected together inline, I get a message stating 20.6 will be changed but it was already defaulted with a green thumbs up, also in bypass I get a message that alot will change when those are also already defaulted with a green thumbs up...smh. Question is how do the options 2.Programmable Option and 31.4,5 and 6 work in unison with each other? Side note while creating this I just realized I did nothing with the decrypt after every thing is done with bypass and RS do i need to click send on the decrypt screen, what is the complete steps in order to complete this. Connect laptop-FL4-Bypass/RS, login, choose settings and load(save), then decrypt, then just unplug, then test or...? Update: I dont think i have a decrypt option...
Login to reply View 1 answer(s)

21/12/2018

 Jeep Levi Kudrna (240Pts.)

0

Need reset to change options

After using my new Compustar system for a few months now, I have noticed an odd behavior of the system. Sometimes at certain store parking lots when I get out of the vehicle and lock the door with the Compustar remote, I will get a reply back on the remote a few seconds later that the doors have just been unlocked. However, the doors remain locked. This unlock reply is the same reply that occurs when doors are unlocked with the OEM remote. The OEM remote does work with the Fortin and Compustar when locking and unlocking. So I really don't know what is going on. I was going to disable the OEM remote monitoring feature, but found out my unit is locked and needs to be reset. Could you please reset my unit?
Login to reply View 1 answer(s)

04/12/2013

 Toyota Gera Belo (130Pts.)

0

Corolla 2013 - G-key - Do I need install something else beside the evo-all

I have Corolla 2013 with G-key. I dont have any remote starter installed in the car, do i need to install something else beside the evo-all in the car to be able start the car with the original remote key that i get from toyota?
Login to reply View 1 answer(s)

14/11/2013

 Volkswagen v@li (210Pts.)

3

Lock & unlock doesn't work in a 2009 VW Passat

Hello! I tried to match an EVO-ALL module with a Viper 5704 alarm system and I have same problems. I asked the seller to flash the latest firmware version with D2D protocol, but I can
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue