Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question

1

IS there a T harness for 2014 Hyundai Sante Fe Sport Push To Start?

Hello, is there a T harness for 2014 Hyundai Sante Fe Sport Push To Start? Did not see one but wanted to double check. Thank you for your time.

0

2019 veloster push to start not working

I just installed the Evo-One with the T harness. I programed the Evo and the started the car. Followed the reservation mode and the hit the push to start button and the car shuts off! I notice that when the car is on the Evo-One only shows a orange/yellow light, that's it. Please help.

0

When using a T Harness is there any other wires to hook up?

Any additional wires to hook up using a T Harness 2019 hyundai veloster manual transmission

0

Why the wiring change in installation guides ?

Installed an evo one in a 2016 Tucson standard key using a T-harness and using guide # 60671, Rev 20160613 the guide available at the time of installation. The newest revision of that guide Rev 20190226 clearly shows the white wire going to the 6 pin main connector on the evo-one coming from the T-harness is now cut off or disconnected and was shown connected in the older instructions. Why is this wire now shown as disconnected and must this wiring change be fixed before I update the hardware/firmware version if needed ?

0

How Can i order a T-Harness for a 2016 Hyundai Santa Fe XL PUSH TO START

I ordered a EVO one unit, but would prefer to have a T-harness for my car to make the unit easier to remove at a later date. Ist here a way to order just the T harness?

0

vehicle wont start with t harness install

evo one install t-harness no pats wire module does not program when key is turned on blue light goes out on module checked can checked a1 yellow wire on proper ign pink wire

0

Need help with steps 4-6 programming EVO-ONE for 08 Hyundai Sonata

I purchased an EVO-ONE, RF-ALL-642W, Flashlink 2, and a THAR-ONE-KHY1 ignition T-harness and made the following connections to my US spec 2008 Hyundai Sonata. I have updated Bypass hardware version 2, firmware version 76.34 and Remote starter hardware version 7 firmware 1.21. Flashlink updater hardware version 4, firmware version 4.03 Cut loop for automatic transmission. Plugged 4 pin antenna wire to Blue connector of 4 pin data T-harness of RF-ALL-642W kit and plugged antenna to other end. I have connected the ignition T-harness at ignition pigtail, parallel soldered the 20 pin Yellow wire to the Pink wire of t-harness at EVO-ONE. Ignition T-harness Black wire ring and 4 pin data Black (added crimp ring) to known good dash ground. 4 pin Black data connector Red wire soldered parallel to Red wire of ignition T-harness. Soldered 20 pin Black parallel to Green wire at foot brake switch. Clipped Green PATS wire at driver kick - White connector (chassis) 20 pin Lt. Blue and 6 pin Red connector White/Green to harness side of Green wire at driver kick. 20 pin Lt. Blue/Black and 6 pin Red connector White/Red to connector side of Green wire at driver kick. 5 pin Grey/Black can low soldered parallel to Yellow wire at OBD-II 5 pin Gray can high soldered parallel to White wire at OBD-II When I hold the programming button down and plug in the 6 pin ignition T harness, Release programming button on Yellow and cycle the key from off to on, nothing happens, the light stays solid Yellow. I have confirmed that the yellow wire is getting 12v only on ignition hot. The car starts and runs with the key for several minutes, I switched the green clipped PATS wire connections and no change was observed. Searching the Q&A I found how to test the can bus by plugging the Black connector in while holding the programming button down, releasing on Blue, then plug the rest of the connectors (all of the ones listed above) in and turn the ignition on. When I do this the Blue light goes out. When I turn the key off, the Blue light comes back on. I have 1.89VDC and 2.27VDC on the can bus lines to a known good ground in the door jamb. Please help! Where do I go from here?

0

Need help with steps 4-6 programming EVO-ONE for 08 Hyundai Sonata

I purchased an EVO-ONE, RF-ALL-642W, Flashlink 2, and a THAR-ONE-KHY1 ignition T-harness and made the following connections to my US spec 2008 Hyundai Sonata. I have updated Bypass hardware version 2, firmware version 76.34 and Remote starter hardware version 7 firmware 1.21. Flashlink updater hardware version 4, firmware version 4.03 Cut loop for automatic transmission. Plugged 4 pin antenna wire to Blue connector of 4 pin data T-harness of RF-ALL-642W kit and plugged antenna to other end. I have connected the ignition T-harness at ignition pigtail, parallel soldered the 20 pin Yellow wire to the Pink wire of t-harness at EVO-ONE. Ignition T-harness Black wire ring and 4 pin data Black (added crimp ring) to known good dash ground. 4 pin Black data connector Red wire soldered parallel to Red wire of ignition T-harness. Soldered 20 pin Black parallel to Green wire at foot brake switch. Clipped Green PATS wire at driver kick - White connector (chassis) 20 pin Lt. Blue and 6 pin Red connector White/Green to harness side of Green wire at driver kick. 20 pin Lt. Blue/Black and 6 pin Red connector White/Red to connector side of Green wire at driver kick. 5 pin Grey/Black can low soldered parallel to Yellow wire at OBD-II 5 pin Gray can high soldered parallel to White wire at OBD-II When I hold the programming button down and plug in the 6 pin ignition T harness, Release programming button on Yellow and cycle the key from off to on, nothing happens, the light stays solid Yellow. I have confirmed that the yellow wire is getting 12v only on ignition hot. The car starts and runs with the key for several minutes, I switched the green clipped PATS wire connections and no change was observed. Searching the Q&A I found how to test the can bus by plugging the Black connector in while holding the programming button down, releasing on Blue, then plug the rest of the connectors (all of the ones listed above) in and turn the ignition on. When I do this the Blue light goes out. When I turn the key off, the Blue light comes back on. I have 1.89VDC and 2.27VDC on the can bus lines to a known good ground in the door jamb. Please help! Where do I go from here?

0

THAR-ONE-KHY1 2010 Versacruz install Guide

Could you send me the instalation guide using the THAR-ONE-KHY1 T-Harness and a EVO-ONE for a 2010 Vera cruise Limited Proximity key. The guide shows one avalable for this application but does not show it in the guide.

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue