Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

22/12/2023

 Audi Scott Edlin (130Pts.)

0

Audi 2013 S4 DSG - Fortin ALL getting stuck on step 7 with 3 x red flashing lights

Just installed a Fortin ALL with the Audi T Harness on a 2013 Audi S4 DSG. UK right hand drive car. When I go to try and get the unit to read the key data I am just getting 3 red light flashes on step 7, everything is fine up until that point and the car operates as normal. When I then put the flashlink back onto the PC software it says invalid key data. Any ideas? I have checked all wiring, also checked status of CANBUS with zero issues showing so I know that wiring is good. Serial no for module is : 001A07445150
Login to reply View 1 answer(s)

28/09/2023

 Lincoln Joseph Nixon (130Pts.)

0

2012 Lincoln MKS Step 7 programming issue, red light goes out when both red and blue lights are to be lit

Upon pressing the brake for step 7, the red light and blue lights are lit, but the red goes out prior to pressing the ignition button. It seems the bypass won't program. When finsihed, and trying to remote start, the car says no key detected. Ideas>
Login to reply View 1 answer(s)

23/01/2021

 Mazda Hovhannes Hakobyan (350Pts.)

0

message "invalid key data" during dcryptor step

message "invalid key data" during dcryptor step mazda 6 2014 start\stop
Login to reply View 1 answer(s)

24/08/2020

 Toyota W. Frazier (210Pts.)

0

2016 Toyota Corolla Evo One

I have used the Toy 8 Harness that came with the Evo One,Module (TOY 8 79/xx/1.xx C1, D5 38.2 Progam Lock). I followed all the steps and when I plug the 20 Pin Connector in the Evo Module, the noise sounds and the dash board warning message says, TURN LIGHS OFF and when I try to Press the button 10 times, the RED and BLUE LEDs fade out by the time I get to 6. I can't get Pass Step 3! I reset it a few times and still the same thing! I switch the Pins and try to use it as a TOY 3 Harness and the same Thing! I even Hard Wired the module using the Diagram and still the same thing! I'm thinking this was a bad Module from the beginnig! I have listen to TECH Support ideas and tried them and nothing works! I've made 7 attempts on wire this Evo One, trying different ways and the Module keeps doing the same thing every time. I'm ready to give up! Any idea, why this Warning Light coming on? Do this warning light be the reason why I can't ger pass Step 3?
Login to reply View 1 answer(s)

21/01/2020

 Toyota Daniel g (160Pts.)

0

2013 Toyota Corolla Evo-All stuck on step 5 in programming procedure

Hi, I installed a remote start on a 2013 Toyota Corolla that uses the Evo-All bypass module. I am currently stuck on step 5 of the programming procedure on page 3. When I turn the key to the on position the blue and red led light from the previous step turn off and nothing happens. I checked all the wiring going to the ODBll with a multimeter and everything seems fine. The remote start does crank over the engine but will not start unless the key is close to the ignition. Does anybody have any suggestions?
Login to reply View 1 answer(s)

12/10/2019

 Chevrolet Kid Ratits (470Pts.)

0

Can'y get blue solid blue led

2006 chevy uplander evo one can't get solid blue led in step 1 programming
Login to reply View 1 answer(s)

12/10/2019

 Chevrolet Kid Ratits (470Pts.)

0

Can'y get blue solid blue led

2006 chevy uplander evo one can't get solid blue led in step 1 programming
Login to reply View 0 answer(s)

18/01/2018

 Chevrolet eric pozdal (130Pts.)

0

2011 chevy cruze step 5 will not change from yellow to red just stays yellow

2011 Chevrolet Cruze, standard switchblade key with ignition cylinder on column (not push to start). Using EVO-GMT1, with the t-harness. Only wire I have wired to the vehicle for now is the brown wire on the 5 pin connector, and that is spliced into the number 1 pin at the dlc for can bus. I can get programming to step 5. I have hit the program button 5 times, and it will flash 5 times in 4 sequences, and then stay on yellow when its done. When i turn the key it stays yellow and nothing happens. I do not want any other feature this offers, except 3 lock remote start. I have verified switching 0-3v at the brown terminal with key on, and have wired it multiple ways to verify it's not something I did. I was able to get it to turn red once, turned the key off, removed the key, waited 5 seconds, and turned the key back on and it stayed red. I am a gm technician and very familiar with these vehicles but I can not get this thing to program.
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue