Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question

03/02/2023

Jeep Nev (130Pts.)

0

Jeep has power but does not crank?

I have programmed the unit sn: 001A07 415854 Evo All. Installed with wiring harness THAR-CHR4 (Both Yellow wires on the harness are connected together). Programmed the unit. All these went according to the documentation, correct leds and all.

My vehicle is a 2011 Jeep Grand Cherokee 3.0CRD Limited with Start Button

I do the 3x Lock Blue Led comes on every time I press the lock button. Then all power comes on, a few seconds later the red and yellow led is solid and the radio shuts off just like it does while it cranks but no crank??

What could I be doing wrong?

Many Thanks!!

0

2010 Ford F150 - PATS key error on first remote start attempt with EVO-All and Compustar CM-4200DX

I used the decryptor and the 1-key programming method on my 2010 F150. Everything seemed to go smoothly, took about 15 minutes to decrypt the key. I've got soldered/heatshrink connections throughout my installation. When I hit the remote start button on my Compustar CM-4200DX, the dash indicators light up like it is attempting a start, but the PATS warning light flashes rapidly (same as if you have an invalid/non-programmed key) and starter does not engage. The Compustar tries a second time, which again - all the dash lights come on as you would expect, but this time the PATS warning light stays on solid (just like it would if you used the key) and the vehicle starts up successfully. Not knowing if the Compustar module could "talk" to the EVO-ALL, I used the hardwire method for the install instead of data-link. I double-checked to make sure the EVO-ALL was getting a proper signal to the GWR, START, Ign, 12v+, and ground wires. Everything works just fine, except that the Compustar module has to try twice before the truck will start.

0

2017 explorer no ignition no crank on start attempt. Get yellow and red then x3 red for no tach

When I attempt to do remote start the red and yellow come on then go off and do second attempt then red flash x3 for no tach. During this sequence the ignition does not come on and there is no crank attempt. Wired with tharness. When you look at my service number on the flash link it does not show all the selections on link it does when look online. Only ones shown on are c1 d1 and d2.

0

EVO ALL NO Crank but Ignition

Hello Whenever I try to use remote start with my viper 5806v and the Evo all, All i get is ignition. After about 35 second the ignition comes on and everything looks normal.But there is not even a single crank that is produced.Ive wired using D2D and Everything besides remote start work wonderful, like unlock, lock and trunk.I have changed the remote starter to automatic mode and turned the Tach sense to off but Nothing.Out of my 100 attempts it has not even cranked once.Thanks

0

2016 Chrysler 200 3 Flashes - No Tach Detected - Ignition on but no crank

2016 Chrysler 200 3 Flashes - No Tach Detected - Ignition on but no crank: I have walked through the troubleshooting guide and checked all of the programming/wire issues that could occur. Any other items to test or check to get the car to remote start? The car attempts to start twice before failing and providing the diagnostic codes.

0

2016 Chrysler 200 3 Flashes - No Tach Detected - Ignition on but no crank

2016 Chrysler 200 3 Flashes - No Tach Detected - Ignition on but no crank: I have walked through the troubleshooting guide and checked all of the programming/wire issues that could occur. Any other items to test or check to get the car to remote start? The car attempts to start twice before failing and providing the diagnostic codes.

0

EVO ALL NO Crank but Ignition

Hello Whenever I try to use remote start with my viper 5806v and the Evo all, All i get is ignition. After about 35 second the ignition comes on and everything looks normal.But there is not even a single crank that is produced.Ive wired using D2D and Everything besides remote start work wonderful, like unlock, lock and trunk.I have changed the remote starter to automatic mode and turned the Tach sense to off but Nothing.Out of my 100 attempts it has not even cranked once.Thanks

0

2015 Chrysler 200 ignition on but no crank

I installed a CHRT6 in my 2015 Chrysler 200 with push-to-start. After coding everything and splicing all the wires I tried the 3x lock and it tries to start twice and fails. I then get 3 blinks from my parking lights.

0

Wired exactly as the install guide said but car won't even try to crank.

Installed an Evo-One and Fortin RF642W 2 way RF kit in a 2003 Buick Century. Followed "connection 1" and "programming 1" as stated to by this install guide. http://fortin.ca/download/23261/evo-one_ig_reg_bi_gm_j1850_b_23261.pdf

 

All wiring has been verified multiple times to be exactly what the install guide said to do...nothing more and nothing less.

 

When I try to remote start the car, via the 2 way remote, the car will power on but will not crank the starter at all. When I use the remote to kick the car into "idle mode", the car unlocks as it should but shuts off when I turn the ignition off to pull the key.

 

Bypass portion programmed fine....RF remote also programmed fine.

 

Literally, the only wires connected at the moment are what the install guide I linked above says.

0

Wired exactly as the install guide said but car won't even try to crank.

Installed an Evo-One and Fortin RF642W 2 way RF kit in a 2003 Buick Century. Followed "connection 1" and "programming 1" as stated to by this install guide. http://fortin.ca/download/23261/evo-one_ig_reg_bi_gm_j1850_b_23261.pdf

 

All wiring has been verified multiple times to be exactly what the install guide said to do...nothing more and nothing less.

 

When I try to remote start the car, via the 2 way remote, the car will power on but will not crank the starter at all. When I use the remote to kick the car into "idle mode", the car unlocks as it should but shuts off when I turn the ignition off to pull the key.

 

Bypass portion programmed fine....RF remote also programmed fine.

 

Literally, the only wires connected at the moment are what the install guide I linked above says.

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue