Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

18/11/2018

 Cadillac Joshua Ramey (130Pts.)

0

Evo-one will not 3x lock start with oem remote

2006 Cadillac Ext. has factory alarm but no remote start. On advice from a friend that is a certified installer, I bought an EVO-ONE since he said it would work with the factory remote and be able to do the 3x Lock with the OEM remote. The unit was installed properly and double checked via installer. Initially, it would not move past having a solid blue led because of yellow wire (A1) on 20 pin connector not being connected, was connected and checked again (this is not shown as needed in the wiring diagram). Initial settings were not allowing for the data signal to be picked up so the unit was re-flashed to 70.18 and the data signal was able to be found and programmed. All applicable settings are as suggested and 3x lock is enabled in the settings with the flash-link. The unit is now programmed properly for the bypass but will not remote start the truck via OEM remote and 3x lock. Needed to use the vehicle and wasn't able to get anywhere with support on Saturday since they're closed. Current firmware flash confirmed: Bypass: 70.18 firmware, 2.0 hardware Starter: 1.24 firmware, 7.0 hardware Thanks for any help.
Login to reply View 0 answer(s)

15/01/2017

 GMC Brendan Horn (160Pts.)

0

EVO ALL NO Crank but Ignition

Hello Whenever I try to use remote start with my viper 5806v and the Evo all, All i get is ignition. After about 35 second the ignition comes on and everything looks normal.But there is not even a single crank that is produced.Ive wired using D2D and Everything besides remote start work wonderful, like unlock, lock and trunk.I have changed the remote starter to automatic mode and turned the Tach sense to off but Nothing.Out of my 100 attempts it has not even cranked once.Thanks
Login to reply View 2 answer(s)

15/01/2017

 GMC Brendan Horn (160Pts.)

0

EVO ALL NO Crank but Ignition

Hello Whenever I try to use remote start with my viper 5806v and the Evo all, All i get is ignition. After about 35 second the ignition comes on and everything looks normal.But there is not even a single crank that is produced.Ive wired using D2D and Everything besides remote start work wonderful, like unlock, lock and trunk.I have changed the remote starter to automatic mode and turned the Tach sense to off but Nothing.Out of my 100 attempts it has not even cranked once.Thanks
Login to reply View 2 answer(s)

11/01/2017

 GMC Brendan Horn (160Pts.)

0

GMC Yukon Remote starter power wire

HI Im installing the Evo-gmt4 currently and a little confused on the instructions.How do I determine if my parking lights are pulling more than 1 amp or that the remote starter needs to be connected directly to the battery.Thanks
Login to reply View 1 answer(s)

17/01/2015

 GMC Malcolm Bridgewater (140Pts.)

1

05 Gmc Yukon remote starter problems

Ok I got the gm-sl remote starter problems truck start then shut down I got all the wires connected to the wires on the install guide except this blue wire that says ground input I don't know what wire from my remote to use on that I need some help please and thank you
Login to reply View 1 answer(s)

28/12/2014

 Bypass MarkC (1850Pts.)

0

EVO-ONE + Tahoe/Suburban/Yukon trunk pop

On my 2015 Suburban I have two "trunks" -- one is power rear glass, and one is the whole rear hatch. My EVO-ONE + RF Kit works fine -- the trunk button on the RF kit remote pops the rear glass. Is there any way to change this to the rear hatch?
Login to reply View 1 answer(s)

30/12/2013

 GMC Chip Salley (140Pts.)

1

Why will evo not program on my 2011 gmc yukon?

Have evo service #001A06266665. When programming the light blinked and then cut off when I cut the key to off position like it should but when I went to hold the key backwards and try to crank it with keypad i got nothing. Unplugged everything and tried programming again but after I hold the reset button and light goes to solid blue and I plug 20 pin connector and white connector and turn the key to on the blue light just goes off completely no blinking or anything and still will not work. Thanks. Hardware vr. 6. Firmware vr. 4.18.
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue