Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Utilisateur

Saaif Khan

À rejoins en date due:

Nov. 21, 2016

Points

550

Commentaire(s)

8

Questions votée(s)

0

Réponses votée(s)

1

Votes positifs

0

Votes contre

1

Votes reçus

1

Votes négatifs reçus

0

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez une question

0

2019 Mazda 6 not starting after successful programming with evo all

Hey everyone, I'm trying to install an EVO-ALL in standalone mode on a 2019 Mazda 6 with a T-Harness. I initially successfully programmed the module with the two keys, and then successfully completed the CAN procedure as well. Unfortunately I could not get it to start, the module would have the red and orange lights on but would make no effort to crank the car. I tried starting over by resetting the module, and now whenever I repeat the programming process I see a flashing red light, which supposedly means that the keys are already linked to the unit. Doing the CAN procedure now also results in all 3 lights cycling instead of the single blue light going off. Simply plugging the module in results in all 3 lights flashing. I'm not entirely sure where to go from here. I'd like to start over but I'm not sure how to do that.

0

2016 Mazda 6 EVO-ALL + MY-START - Key Takeover Possible?

Hey everyone, I am planning to install an EVO-ALL and a MY-START into my 2016 Mazda 6 soon. The only thing that is puzzling me is why a key-takeover is not possible when using the THAR-MAZ1 harness, but is possible without it. Looking at both guides, I don't understand the differences. I can see that the direct wire guide uses "Ignition 2" on the 32-pin white connector, and the THAR-MAZ1 guide uses "Data-key" on the 32-pin white connector. This seems to be the only differences in the two guides, and I can't imagine that this is what affects the key-takeover functionality. If I am understanding this correctly, key-takeover is only possible if the EVO-ALL can detect an unlock signal when the vehicle is running. How can the EVO-ALL detect this signal when it is wired directly compared to when it is wired using the harness? If, for whatever reason, the EVO-ALL cannot detect the OEM remote's unlock signal when the vehicle is running, what about the MY-START? This is an RF-KIT, which means that it's signals should be unaffected by whether the vehicle is running or not. In this case, if the vehicle was unlocked with this, would it still shutdown once the doors were opened? Any help will be greatly appreciated!

0

2012 Acura TSX - Honk horn instead of beep?

I've installed an EVO-ONE into my 2012 Acura TSX, and everything works great, but I'm just wondering if it is possible to use the power of the EVO-ONE to honk the horn whenever I lock the car. The problem is that it's almost impossible to hear the tiny beep from any sort of reasonable distance, and since that's the only way to confirm whether or not the car is started, it would be nice to use the horn output as well. If anyone knows a setting for this, or how it could be done, please let me know. I have already hooked up the horn output of the EVO-ONE to my car, but that only seems to work for the alarm. Thanks!

0

No persistent trunk status using EVO ALL and Crimestopper RS7 on 2005 G35

Not sure if this is intentional, or simply not supported, but I've noticed that my 2-way remote starter does not correctly show the status of the trunk. Since the system is 2-way, I can see whether the doors are locked/unlocked, opened/closed and whether the hood is open/closed. These are all persitent, so they will remain on the key fob until their status is changed. The only thing missing is that for some reason I cannot see the status of the trunk. I can open the trunk using the key fob, but it does not show that the trunk is open or closed. None of this is manually wired up, it is all CANBUS. There should be the "trunk status" which is supported by the EVO ALL and the Crimestopper RS7 according to the manuals. There is actually even a dedicated wire in this car which goes low when the trunk is open. I'm just wondering if anyone knows how to get the trunk status working.

0

HONDA CIVIC 2007 DOOR LOCKS

THE HARNESS FOR THE DOOR LOCK WIRES IN THE MANUAL NEED TO BE HOOKED UP. I CANT FIND IT I HAVE LOOKED AND GOT NO WHERE. NOW THE CAR STARTS, UNLOCKS THE DOOR AND LEAVES IT OPEN. CAN I CHANGE THE OPTIONS ONLINE? DO I NEED TO USE THE WIRE? HOW DO I KNOW THAT I HAVE THE RIGHT FIRMWARE? PLEASE HELP I THANK YOU.

1

Evo All Lock/Unlock/Trunk rapidly flashing all lights when pressed on 2005 G35

I have my EVO ALL installed alongside a Crimestopper RS7 remote start kit, and for some reason, whenever I press the lock, unlock or trunk release button, and my lights are on, it will not flash the parking lights, but instead, it will flash my Xenon headlights, fog lights, and whatever else is turned on rapidly for about 2 seconds. I don't have my parking lights physically wired up, so this is being done entirely through CAN. I'm just wondering if this is a bug, or if there is a way to disable flashing the lights, or if anyone knows anything else! **Something worth noting is that I have the Canadian version of this car, with Auto headlights and daytime running lights. This might be the cause of the problem, but I don't know how to fix it. Thanks!

No results

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez une question

Support Technique

Recherchez parmi nos produits les plus populaires et les sujets d'installation disponibles dans notre section Questions et réponses.

En savoir plus
Téléchargez notre application de guides de dépannage étape par étape disponible pour iOS et Android ou parcourez notre version de bureau.

En savoir plus
Accédez à la plus grande base de données de schémas de câblage et de photos en ligne de l'industrie. Un jeton gratuit est fourni dans chaque boîte EVO-SERIES.

En savoir plus
Vous n'avez pas trouvé l'information que vous cherchiez ? Posez-nous une question en remplissant le formulaire de demande de support technique. Un spécialiste produit vous répondra sous peu.

En savoir plus
Des solutions de contrôle à distance et de connectivité à la fine pointe de la technologie au soutien technique haut de gamme, découvrez pourquoi vous devriez choisir les produits Fortin.

En savoir plus

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer