Questions & Réponses

I have a 2015 Corolla with an automatic transmission start button. 

Installed with THAR-TOY6 T-Harness & EVO ALL

The device flashes blue when opening or closing the doors, but when trying to operate it with the remote, it flashes 4 red flashes.

Flash blue once before red flashes

Please see the attached video.

https://photos.app.goo.gl/6rfod5uAwRBQ7MgUA

I buy FORTIN EVO ONE ALL + THAR-TOY13 + FORTIN RFK441+ fortin flashlink tools

I followed the installation instructions, but it didn't work I installed the device and made a flash, and when opening or closing the door, it flashed in blue, but when pressing 3 times to close, the remote start did not work I tried to flash the device again but it stuck in (DCRYPTOR'S LIMIT HAS BEEN REACHED FOR THIS CAR)

Hi,

My evo-all used to working with the OEM key 3-locks-to-start before.

Then I bought the RM 942 RF KIT.

Flashed the evo-all to 78.70, and the antenna to 1.05 already.

Followed the DCRYPTOR PROGRAMMING PROCEDURE. All leds are off at step 5 indicating it's already programmed.

After all these, it seems everything are connected and paired correctly. The lock/unlock buttons on the RF kit work properly.

BUT neither OEM key 3 locks nor RF kit key remote start ([+] + lock) could remote start the car. After pressing the OEM key 3 locks, I can hear the evo-all or some car electric component making the small clicking sounds, and the car turn signal lisghts had a couple of follow-up flashing, which seems to me like the evo-all is indeed carrying out the remote start procudre. But car does nothing, no cranking sound at all.

Did I miss anything again?

One weird thing to me is that I think I installed my evo-all with a T-harness, but in the Flash Manager software, after I select TOYOTA, SIENNA 2020, PUSH-TO-START, STANDALONE, there is only STANDARD CONNECT option but on T-HARNESS CONNECTION option in the connection type selector. Is this the problem?

Thanks,

Gerry

When 3X lock is pressed vehicle starts. Then when started the FOB doesn't work while vehicle is running and have to use the key to enter the vehicle.

I've installed 2 other remote starts in 2013 Corolla and 2016 Tacoma, and after vehicles has started, I can still use the key FOB to unlock the door. I can also click 3X on the lock and shutoff vehicles. But I can't do it with 2014 camry...did I miss a wire? or is this normal operation?

thank you.

3X lock and vehicle starts. Now key FOB doesn't work while vehicle is running and have to use the key to enter the vehicle. 

I've install in 2 other vehicle and after vehicle has started, I can still use the key FOB to unlock the door. I can also click 3X on the lock and shutoff vehicle. But I can't do it with this camry...did I miss a wire? or is this normal operation?

thank you.

wont start and no led indications whatsoever on module when key fob button pushed 3times .

Any experienced with EVO-ALL thar-toy13 harness connections ,all plugs in do i need to leave any disconnected?

wont start and no led indications whatsoever on module when key fob button pushed 3times .

Any experienced with EVO-ALL thar-toy13 harness connections ,all plugs in do i need to leave any disconnected?

I am not using a T harness. I have double and tripple checked my wires and even tried reversing the TC and RX wire but when I do the 3x lock it flashes and clicks on the bypass but it does not power the ignition. The yellow light does not illuminate on the bypass. I was able to get the car to start 3 times out of 20 attemps. It was typically right after either programming the module or starting the car, shutting it down and then immediately remote starting it but I cannot consistantly replicate this. Im wondering if there is an issue with the module. I do not have another to swap it out with to try.

I have tried to see if there is a factory remote starter by pressing the lock button 3 times and on the 3rd holding it for 3sec and the car does nothing leading me to believe there is no factory remote starter on it.

The 12 digit service number on mine is 001A06846569