Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question

0

RM 942 buttons have wrong functions

Hi, I flashed my evo-all to match my vehicle: * Toyota Sienna 2020 * Standalone installation * Standard connection * push to start * No alarm Flashed the evo-all to 78.70, and the antenna to 1.05 already. The rm 942 fob could connect to the car, but the lock button opens/closes the driver side sliding door, the unlock button opens/closes the passenger side sliding door, with just one press. And the remote start button doesn't work at all. Did I miss anything? Thanks, Gerry

0

toyota sequoia 2015 evo all does not start and does not lock the doors

Toyota Sequoia 2015, EVO All, I made the corresponding installation following the instructions, I did the programming of the module at the end and everything went well until i tryed to start the car and does not turn on, I checked  the ground connection of the remote start and it's all right, and follow the instructions of connection for the Evo all for the Toyoya Sequoia 2015 and the instructions say that with the connection of data link, do not need to give ground to the Evo all (dark blue cable , ground when the remote start is running) the only function that is doing is the unlock of doors, when I give this order the blue LED get on, but when I give the ignition order only the yellow led get on and when I give the option to lock doors No LEDs are turned on. You think it's better to make connections directly from the EVO all status output wires to the remote starter input wires.

(the module have been flashed FIRMWARE VERSION 79.[43] )


 

0

Remote Start Stop Working

I have an EVO All installed with T-Harness in a 2022 Rav4 Hybrid PTS. Everything worked fine till I installed and try to use EVO-START 2. I later noticed that I did not programm the EVO_START 2. I did it and since then it never worked and even the 3x lock remote start stop working. I also tried to Master Reset. It seems to work while doing it on the module but when I connect the EVO ALL to FLashLink the module is stil programmed. Nothing was reset. When I start the car, the middle Yellow LED turns on. SN: 001A0785010

0

2020 Toyota 86 (PTS) starts for 2 seconds then turns off

I have an automatic 2020 Toyota 86 (PTS) with an EVO-ONE installed. From my knowledge, we have all the wires tapped properly. We ran into a few issues with the immobilizer wire but I believe we got that part sorted out. To confirm with the immobilizer wire, we cut the yellow immobilizer wire in half, tapped the light blue black and yellow red to the immobilizer wire that's connected to the ECU, and tapped the yellow green to the immobilizer wire that's connected to the other side of the car. Is this correct or should it be flipped? We're not able to aquire the immobilizer data for DCryptor but I think it's because it's not listed as supported on fortin's website, even though we go through the guide and finish with the Yellow and Red lights alternating on the EVO-ONE before attempting to use DCryptor. (Leaves us with a 'No data found' error). Finally, we installed the antenna for the RFK411 remote and programmed it. When starting the car, it starts for about 2 seconds then turns off. Does anybody know what could be causing this issue?

0

2014 Camry fob not working after remote started?

When 3X lock is pressed vehicle starts. Then when started the FOB doesn't work while vehicle is running and have to use the key to enter the vehicle.

I've installed 2 other remote starts in 2013 Corolla and 2016 Tacoma, and after vehicles has started, I can still use the key FOB to unlock the door. I can also click 3X on the lock and shutoff vehicles. But I can't do it with 2014 camry...did I miss a wire? or is this normal operation?

thank you.

0

16 Tundra, Evo Key, no start

Used connection 5, programing 3 in manual. Wires were easy to find, did not use key sense. Believe truck does have a factory alarm (If that matters), it does have a factory keyfob. Programming does what it says it will do. Remote start is a Viper. Everything remote starts fine if I leave the key in the ignition. If I don't, security light blinks and remote start doesnt work. I have the flash link and everything was already updated, and it didn't give me any options to change or adjust anything. Just update. GWR is connected to the Viper. Only the red light comes on the EVO Key if I remote start it. Is this normal? I'm sure im forgetting something.

0

2015 Toyota Corolla H-Key Without Smart Key Remote Start will start but won't keep it on.

Hi I have an Evo All updated to the lastest firmware as of today (12/11/2020) 79.65 I believe, with all preset options, meaning i did not turn on or off any feature on the Evo All through the FlashLink Manager. To pair with the Evo All I have an Encore E1. My vehicle is a 2015 Toyota Corolla L H-KEY without smart key (no lock or unluck button on it) Evo All Installation Guide with Remote Start Unit https://cdn02.fortin.ca/download/31711/evo-all_ig_reg_bi_toy-corolla_2014-2016_hkey_h_31711.pdf Encore E1 Installation Manual. https://encoreautomotivesystems.com/content/pdf/one_sheet_E1_install_manual.pdf So I have all the Evo All cables connected to the car which are A20 to 30-pin connector position 16; A18 to E3 White 40-pin connector position 34; A10, C3, and C4 to OBD-II connector in its respective positions 7, 6, 14; Also I have the Encore E1 connecting to the Evo All which are 10 Pin Encore E1 connector -> 20 Pin Evo All connector White/Red Tachometer -> A12 White/Black Hood Pin -> A15 Black/White Brake Shutdown -> A11 White Ground when Runing bypass output -> A8 Pink Security Disarm Signal -> this is connected to Lt. Green wire in the Driver Kick white connector. So its missing couple wires to be wireout such as: Encore E1 10 pin connector White/Blue Instant Start Input (+) -> which i have no idea what is the purpose of this wire and where to connect. Gray Channel 3 Trunk Output -> i didnt do it because i dont have a eletronic trunk release, mine is manual pull up type. Blue/Black ACC2 -> because my vehicle doesnt have a second ACC Yellow Ignition 3 output -> again because the car doesnt have it. So, to summarize, the vehicle locks and unlock just as it should through the Encore E1 4-Button remote control, however, the remote start function will turn on the car in the first try but it will only stay on for 5 seconds, then it shut itself off. After, it tries to start it again, and the cycle repeats 1 more time after that, totaling 3 tries. It starts but wont keep on after 5 seconds. What am i doing wrong? what am i missing here? I have no idea whats missing or why this is happening. If someone has an idea, please share with me. Thank you so much.

0

EVO All Activating 4wd in Rav4 2012

Problem 1 - The remote start sequence only works about 30% of the time Problem 2 - Sometimes when I turn my car on the 4wd function will be activated along with the ABS light on the dashboard. I can tell 4wd is in fact being activated but the weird part is that typically I would need to also lock my differential (that is the button you press to turn AWD on) but that light is not on and the mode will NOT be deactivated if I surpass 25MPH. Faulty device or common issue?

0

toyota sequoia 2015 does not start and does not lock the doors

Toyota Sequoia 2015, EVO All, I made the corresponding installation following the instructions, I did the programming of the module at the end and everything went well until i tryed to start the car and does not turn on, it keep givin starter, it seems that the module does not work, additional only unlock The doors but when I push block it, it does not, the only function that is making the module is the unlock of doors, need to be programmed differently or what can i do. Thank you

0

MyCar Telematics starts then turns off after a few seconds

Vehicle: 2011 Toyota Corolla S (G-Key), manufactured in CAN.

Evo-One w/T-harness installed and working properly using OEM remote (3x lock to start).

 

When trying to start vehicle via the MyCar app, the engine will start and as soon as the doors auto lock the engine will shut off.

 

I have installed the MyCar Controls telematics unit based on the guide here: http://cdn02.fortin.ca/download/64631/autolink-install-guide-64631.pdf#page9

I used the HRN-LLRS-01 connector as instructed.

“Fortin 2” selected in RF section of configuration tab in FlashLink Manager.

MyCar Controls app Device Protocol: Fortin

 

Please help!

0

2005 Toyota Tundra 4 DOOR Can't find doorlocks wires in kick panel

Cannot locate Doorlock wire colors in drivers kick and nothing from the door meters out high or low in regards to switching. Am I missing something here? I've tried 10 different sources and they all claimed different options and wire colors. Non of them panned out.

0

MyCar app not showing runtime and only starts less than half time.

2014 RAV4. EVO All. Crimestopper Cool Start RS00-G5. T-harness. I finally got this setup to work with the OEM black H-key remote with 3X Lock press. I still don’t get a parking light conformation, and the doors won’t unlock, via automatically or with the fob. The MyCar app shows battery and signal levels, and GPS location. No runtime, or remote start conformation. It only seems to start after I open the map and it is located. Then it will start, shutdown and locks require the same. I do have a Fortin flashing tool, and don’t know what else to do. Please help?!?! Thank you!

26/06/2018

Toyota