Questions & Réponses

I finished installing EVO-ONE on my '17 Tundra.  What do the following settings/options do?

I bought two of these.  One for an EVO-ONE, one for EVO-ALL.  I managed to get the EVO-ONE working on a 2020 Hyundai Kona.  I cannot get it  to work on EVO-ALL with multiple vehicles (2010 Ford Fusion, 7.71.52 and 2014 Chrysler Town and Country, 7.58.01)

The instructions both in the box and on the Fortin website did not work.  Here is what I figured out to get the antenna into pairing mode:

Unplug antenna if you already connected it

Unplug data link (black connector) from EVO-ALL

Hold programming button

Insert data link

Release button when lights are blue and red

Connect antenna (On this antenna, it flashes once.  If I hook up the antenna from the EVO-ONE install, it flashes 6 times)

Ignition on

Ignition off

Ignition on

Antenna is lit up solid

Within 5ish seconds, press the brake pedal 4 times (antenna should flash with each press)

After the 4th press, it should be flashing rapidly

At this point I was hoping I could program the remotes but they still did not respond.

So far, when I asked Omega support they responded with "Was the evo-all set for Omegalink/Crimstopper rf kit and did the box for the olrf15sst have the white label stating it was compatible?" which is Yes and Yes.  They then followed up with "Just the RF kit protocol and the adapter should be fine. Try holding the start button for 3-5 seconds when you program it."

I get the same behavior with either their adapter or the RF-A2A

Any other ideas from Fortin?  Hopefully my new steps will help.  I reached out to Omega also for clarification about the antenna blinks


EDIT: Omega has been more responsive but no luck so far.  I did try updating the firmware on the Chrysler to 7.74.39 with no luck.  I flashed back to 7.58.02.  Now I no longer get 1 blink when I plug in the antenna in any scenario, only 6 blinks.  (5 blinks is a 1 way antenna, 6 blinks is 2-way according to Omega).  I also am no longer able to replicate my steps above because of this.  One thing is they were not sure if the antenna is supposed to light up when programming an EVO-ALL.  It sometimes does for the EVO-ONE.

Hello.

Try to use evo-key on toyota matrix 2006.  I used the latest FORTIN manual "Guide # 84651". All wires connected, double checked, reconnected. 

Several times after re-insert 4-pin connector Red and yellow led flashing and I stopped on step 4, red led not flashing 10 times after key inserted. But now after re-insert power - red led lit and no other reaction, yellow not flash.

추적 번호는 어디에서 찾을 수 있습니까?

Hi, So when i try to complete the final step of the programming steps by pressing and holding the program button the blue and red lights temporarily go out and then come back on but car does not start. I have all the wiring correct checked more than 4 times. I have checked the wiring to the module and everything. When i program the keys I did follow a step. when I turned the key to the run postion i waited for the seat belt to chime 3 times and then i'd pull out the key I did this for both keys. I would also like to add that both keys are factory oem. I didnt flash this i bought the modul pre programmed

Thank you for any help you give

Update:

After spending some time reasearching other possibkle soultions I was able to get the keys to program. I went off a guy who I saw on youtube install the same module I did but he wasnt specific of when he started counting prior to putting the first key in so I started counting after the first seat belt chime but it was to long. For those who are reading this in the future and are still struggling with the programming step.Its not an easy step don't let anyone fool you. It took me nearly 1 1-2 hours to get this to program. An easy tip I learned is soon as your turn the key to the run postion and you hear the first chime starting counting 1 Mississippi 2 Mississppi 3 Mississppi try to finish your count before the third seat belt chime and you should be good to go.

I just got a Linkr-LT2. It came with the Linkr-LT1 quick install guide. I followed the steps in the quick install guide but the unit does not work.
The Linkr LT app only shows my car battery voltage and connection signal. The GPS tracking is working fine. The START/STOP/LOCK/UNLOCK
don't work. I searched the internet and found the "mycar installation guide". I followed the steps to learn the Linkr-lt2 to the Evo one. I turned on the "Fortin 2" function on the EVE ONe.  I pressed and held the valet button for 5 seconds but the RED led light on the Evo One did not turn on.

Problem SOLVED. .Linkr LT2 is working fine now...

I found the video on youtube 12voltsolution.  The guy pressed the UNLOCK button on car key several times to neutralize the EVO ONE before he did the following steps.

STEP 6. LEARN THE MYCAR TELEMATICS DEVICE TO THE EVO-ONE
In order to communicate with the remote starter, the telematic system must be learned to the EVO-ONE.
1 - Cycle the ignition to the ON position.
2 - The YELLOW LED on top of the EVO-ONE should come ON.
3 - Press & Hold the EVO-ONE programming Valet button for 5 seconds.
4 - The RED LED on the side of the EVO-ONE will Flash rapidly.
5 - Release the push button.
6 - Press & Release the push button 5x times. Everytime the push button is pressed the parking lights
& the RED LED on the side of the EVO-ONE will blink.
7 - Then Press & Release the Brake pedal.
8 - At that same moment the RED LED on the side of the EVO-ONE will blink once to confirm that the
Telematic device ID has been learned to the EVO-ONE.
9 - Cycle the vehicle’s ignition to the OFF position to Exit the EVO-ONE programming.

For a few weeks I ahve been trying to either retrieve or register an new account on wirecolor. It has been and is currently unavble to do any of these functions as the reCaptia is broken. This prevents any requests from being sent. In addition the "contact us" link is a broken one ad redirects to an error page.