Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question

0

Changing options after installation

Hi all, Just wondering if there is a general rule as to what needs to be unplugged if we need to change options on a module (EVO-ALL or EVO-ONE) without removing it from the car? Just the 4-pin cable? Remove all of the cables? I'm going to be adding an RF-kit and will need to change that setting. Thanks

0

Flashlink Manager won't recognize Evo-One Module

Just purchased a flashlink 4 updater. Downloaded the software but it won't detect that the evo-one is plugged in. Updater is on latest software.

0

What does option 24 do?

What does option 24 do? - No power output relay in idle mode - Ground output in idle mode only I will not accept "if the installation guide doesnt say to mess with it then dont worry about it"

0

Datalink Protocols Disabled

I know this question has been asked but seen no official answer on it. I was trying to enable D2D (F3) in Datalink Protocols and couldn't as they are greyed out. Can't turn them on or off. I'm using the recommended firmware for my 2021 Jeep Cherokee PTS with evo-all firmware 68.03.

0

Resetting evo one module/bypass.

I need the dcryptor, bypass and remote starter prgramming locks reset on my module. Can't get this 2018 Tiguan push to start to work. Bypass zone 002B04235393. Remote start zone 002B07235393.

03/07/2022

FAQ G M (15020Pts.)

0

switch mode

Hello. I want to install evo-one (002B04233785). But I can't open the bypass window. I tried to enable-disable valet mode, but it doesn't help. The remote launch page (1.25) opens. And if I go to the bypass page, an empty window will appear and SWITCH MODE is written to the left. When I press it, all the LEDs on the module start flashing together and that's it ...

0

Evo-ALL - try reset but getting 3 solid LED lights

Hello, I was getting the solid red light on my Evo-all. I decided to do a reset. I installed firmware 0.99 and while pressing programming button and connecting datalink from the car Instead of getting the solid red light I got all three solid lights. Can anyone tell me what does it mean and how do I get it to work ? I'm trying to install remote start to 2020 Rav4 XLE premium with push start.

1

2018 Ford Fucus Key programming issues

Hi, So when i try to complete the final step of the programming steps by pressing and holding the program button the blue and red lights temporarily go out and then come back on but car does not start. I have all the wiring correct checked more than 4 times. I have checked the wiring to the module and everything. When i program the keys I did follow a step. when I turned the key to the run postion i waited for the seat belt to chime 3 times and then i'd pull out the key I did this for both keys. I would also like to add that both keys are factory oem. I didnt flash this i bought the modul pre programmed

Thank you for any help you give

Update:

After spending some time reasearching other possibkle soultions I was able to get the keys to program. I went off a guy who I saw on youtube install the same module I did but he wasnt specific of when he started counting prior to putting the first key in so I started counting after the first seat belt chime but it was to long. For those who are reading this in the future and are still struggling with the programming step.Its not an easy step don't let anyone fool you. It took me nearly 1 1-2 hours to get this to program. An easy tip I learned is soon as your turn the key to the run postion and you hear the first chime starting counting 1 Mississippi 2 Mississppi 3 Mississppi try to finish your count before the third seat belt chime and you should be good to go.

1

2018 Ford Fucus Key programming issues

Hi, So when i try to complete the final step of the programming steps by pressing and holding the program button the blue and red lights temporarily go out and then come back on but car does not start. I have all the wiring correct checked more than 4 times. I have checked the wiring to the module and everything. When i program the keys I did follow a step. when I turned the key to the run postion i waited for the seat belt to chime 3 times and then i'd pull out the key I did this for both keys. I would also like to add that both keys are factory oem. I didnt flash this i bought the modul pre programmed

Thank you for any help you give

Update:

After spending some time reasearching other possibkle soultions I was able to get the keys to program. I went off a guy who I saw on youtube install the same module I did but he wasnt specific of when he started counting prior to putting the first key in so I started counting after the first seat belt chime but it was to long. For those who are reading this in the future and are still struggling with the programming step.Its not an easy step don't let anyone fool you. It took me nearly 1 1-2 hours to get this to program. An easy tip I learned is soon as your turn the key to the run postion and you hear the first chime starting counting 1 Mississippi 2 Mississppi 3 Mississppi try to finish your count before the third seat belt chime and you should be good to go.

1

2018 Ford Fucus Key programming issues

Hi, So when i try to complete the final step of the programming steps by pressing and holding the program button the blue and red lights temporarily go out and then come back on but car does not start. I have all the wiring correct checked more than 4 times. I have checked the wiring to the module and everything. When i program the keys I did follow a step. when I turned the key to the run postion i waited for the seat belt to chime 3 times and then i'd pull out the key I did this for both keys. I would also like to add that both keys are factory oem. I didnt flash this i bought the modul pre programmed

Thank you for any help you give

Update:

After spending some time reasearching other possibkle soultions I was able to get the keys to program. I went off a guy who I saw on youtube install the same module I did but he wasnt specific of when he started counting prior to putting the first key in so I started counting after the first seat belt chime but it was to long. For those who are reading this in the future and are still struggling with the programming step.Its not an easy step don't let anyone fool you. It took me nearly 1 1-2 hours to get this to program. An easy tip I learned is soon as your turn the key to the run postion and you hear the first chime starting counting 1 Mississippi 2 Mississppi 3 Mississppi try to finish your count before the third seat belt chime and you should be good to go.

0

XL202 option not showing in unit options for evo-one in flashlink

I am looking to get a viper remote/antenna, with an XL202, but before doing that i went to make sure I could configure my evo-one properly. Problem is, it appears that I can't. here is what i see when i open the unit options. There should be an XL202 option next to fortin 2 https://emu.bz/4KM.png here is module info: https://emu.bz/IBM.png (btw could a staff member reset the flash limit on the remote starter, i tried different firmware versions to see if the option would unlock) firmware update version https://emu.bz/tKA.png flashlink version 4.51 2019 kia forte standard key

28/03/2021

FAQ Jim (850Pts.)

0

Programming EVO-ONE to use MyCar telematics and RFK441

Is it possible to have the MyCar and the RFK441 coexist? It seems the answer is no. I can have both the MyCar and the RFK441 programmed to the EVO-ONE. And inidivually they will work and operate the EVO-ONE. But if I plug in the RFK441 into the harness of the MyCar to have both of them attached to the EVO-ONE, only the RFK441 controls the EVO-ONE. If it is possible, what steps can be taken to make this happen. Or do I need a different remote kit for this to work? Thank you. Jim

21/01/2021

FAQ P Patel (280Pts.)

0

Flashlink manager EVO-ONE - missing RFKit programming option

When connected EVOONE to flashlink manager; Do not see "RF kit compitible" menu under "REMOTE STARTER" tab. Any reason its not visible?

21/01/2021