Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question

0

2008 Altima PTS

I installed on 2008 altima pts, car remote starts but only runs for about 3 seconds then shuts off when pressing lock button on oem remote 3x. Any way to resolve my issue? Tech support said firmware downgrade was needed. I changed to 72.23. That didn't work. Need help please

0

Nissan Altima 2008 hybrid bush to start evo all not working

I recently bought EVO ALL stand alone remote start, all wiring and programming done, on testing it start for 3 seconds then switch off repeated again and switch off again, then red light flashing 3 times. please help Hardware: v 6 fermware : v 71.29 service# : 003606004550 note : no flasher available

0

2008 g35x no longer needs OEM keyfob?

I just installed the EVO-NIST1 standalone with the Fortin RF642W RF Kit on a 2008 Infiniti G35x according to Guide 24031 and have a couple comments & questions after playing around with it:

1) LOCK x3 works with the OEM fob, however it cannot remote stop the car with LOCK x3 again. This is known, so it is not a problem.

2) After remote starting the car and unlocking it (either with door button or with either of the fobs), I can open the door, step on the brake, and I am able drive away. That works as intended, but the problem is I can drive away without having the OEM key fob around. The instrument cluster screen does not say NO KEY like it normally would if the key has left the car. In other words, one would be able to drive off without having any remote on them as long as the car gets remote started followed by an UNLOCK signal. Are remote starts intended to bypass the need to have the OEM Intelligent keyfob for the take-over?

3) While the engine is off, the LOCK signal from either the RF fob or OEM fob will lock the doors and prompt the RF antenna's LED to start flashing (blue) and will not stop unless I press the UNLOCK botton on either remote. What is this flashing for? Can this be disabled? I do not need or want any alarms or extra security features. I am more concerned about it draining the car battery. Please advise.

4) After remote starting, the first press of UNLOCK with the RF fob ONLY turns off the Antenna's flashing. I have to press unlock a second time to unlock the car, however it would unlock all four doors at once. I had configured it through Flash Link (B1 on) to unlock driver door on first press, and lock all on second press but that isn't the case. What exactly happens on the first UNLOCK that stops the antenna's LED flashes? Can I get the unlock button to unlock the doors on first press?

5) How does IDLE mode pertain to push-to-starts where the key does not need to be in the ignition? I'm guessing it is not needed but just want to be sure.

6) I had to use the RL2 connector to get remote starter to work, although the guide says RL1 for G35. This might be the issue with folks who cannot get their '07 - '08's  to remote start.

0

2008 Nissan Altima engine shuts off when door opens

I have just installed the EVO-ALL in my 2008 Nissan Alitima (push to start). All features are working properly, such as door locks, lights, windows, and even the remote start. My only problem is that when the car is running, I unlock the door, open it and the engine shuts off. How do I make it so that my car remains running when I open the door?

0

2008 Nissan Altima engine shuts off when door opens

I have just installed the EVO-ALL in my 2008 Nissan Alitima (push to start). All features are working properly, such as door locks, lights, windows, and even the remote start. My only problem is that when the car is running, I unlock the door, open it and the engine shuts off. How do I make it so that my car remains running when I open the door?

22/03/2015

Nissan Jim (850Pts.)

0

2008 Altima Problems with unlock.

Installed an Evo-All in a 2008 Altima as a stand alone remote start with a FT-D100 RF kit. It is programmed On for "Unlock driver door only." The issue I am having is that when you press the unlock button once, the lights blink but the driver door does not unlock. Press the button again and the lights blink and all the doors unlock.

20/03/2015

Nissan Jim (850Pts.)

0

No installation sources for Nissan Altima - Push-to-Start (2007-2008)

I need but am unable to find installation help (wires, photos, guide) for Nissan Altima - Push-to-Start (2007-2008) on wirecolor.com. I can find the information for Nissan Altima - Push-to-Start (2009-2012). I think they are the same but not a hundred percent sure. Can anybody confirm that. Thanks.

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer