Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

User

Ted Bennett

Joined on the:

Dec. 30, 2016

Score

720

Comment(s)

9

Voted question(s)

0

Voted answer(s)

1

Votes up

0

Votes down

1

Votes up received

1

Votes down received

0

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask a question

0

Relay needed for 2010 Subaru Impreza Starter2?

I have installed an EVO-ONE on 2 subarus so far, 2009 WRX and 2009 Forester. When I went to look at installing one in my 2010 STI i re-loaded the settings from my 2009 WRX as a good starter as I know it worked well. In Setting 2 (programmable output) I noticed the setting I had programmed 2.1 (which was likely suggested before) was not the one with the thumbs up icon which was 2.4. The wiring instructions still show using a relay for (+)STARTER2 and (+)ACCESSORY, however the suggested setting shows (+)STARTER2 connected to a direct wire from the EVO-ONE and no (+)ACCESSORY wire listed. Why does the suggested option not seem to match with the instructions? Has anyone used the thumbs up selection 2.4 and NO RELAY at all and just NOT connect ACCESSORY?

0

Doors lock twice when Lock button pressed once on Compustart RF-1WG9 remote

I installed an EVO ONE today on a 2009 Subaru Forester. All functionality seems to work except for when I hit the lock button I can hear the locks pulse twice. When I hit unlock it acts normal with driver priority and all doors on second press which is normal. I don't have any of the lock/unlock wires connected as it works thru CAN. I do have the lock data wires connected as instructions say. I also tried this RF kit on my Subaru Impreza with EVO ONE and it does the same double lock.

0

Parking Lights Resistor

On my 2005 dodge dakota installed evo one and it all works properly however my parking lights keep going off as ther resistor fails. I used a 1.5k ohm 1/2watt metal film resistor. Should i use a higher watt resistor or type of resistor such as carbon film?

0

Subaru hatch release not working over CAN

It looks like the hatch release on 2009 Subaru Impreza does not work with either the trunk button using a Fortin remote or with a Compustar remote. Should this work over CAN without issues or does it require a seperate wire? Trunk Open is listed as compatible for this vehicle. When I hit this, all I see are lights flashing a few times.

0

How to get Evo one to program RF remote for 2011 Nissan frontier

Can't get Evo one to work

0

Explain these options please (remote starter side)

I finished installing EVO-ONE on my '17 Tundra.  What do the following settings/options do?

  Option 9 - Active or Passive Starter Kill What does this do?  I am using the EVO-ONE as the bypass and remote starter.  I do not have a separate alarm or remote starter installed.  Does it even apply to me?   Option 11 - Confirmation I currently have 11.1 enabled (I think by default) but my vehicle chirps on every key fob press. (Option 11.2 is for "Lock/unlock sound always," but, like I said, option 11.1 is enabled.  It's as if option 11 is ignored or vehicle's settings override this option.)   Also, what is an "Antenna LED?"   Option 15 - Smart Door Lock It is currently set at "15.1 Disable," but my vehicle automatically locks the doors if it doesn't open after a certain amount.  (And I can set that time value through my vehicle's stock headunit.)   Option 20 - Engine Supervision What is this?  I have no idea.   Thank you in advance.   Remote Starter - 002B05017153 Bypass - 002B02125187

1

3x lock vs lock-unlock-lock compatibility

Is the compatibility for 3x lock vs lock-unlock-lock the same - meaning vehicles only on the list for 3x lock will work with either? What limits this ability on cars not compatible?

0

RF-2W803-SS with evo one not programming

I am using the included ft-d100 adapter that came with Compustar RF-2W803-SS. I grounded and connected the 12v adapter. I went through the steps in the programming guide. Turn ignition to on position, press and hold valet button until horn chirps, press valet button 1x, press brake 1x, press lock button on remote, press brake 1x, turn off ignition.

I did not modify the 4-pin connector at all. The 4-pin connector has the white and blue wires crossed like suggested. 

Is there another way to program the rf kit?

0

Polarity of the AUX1 output on EVO ONE?

Is this positive or negative output pulse?

No results

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask a question

TECHNICAL SUPPORT

Search through our most popular products and installation topics available in our Question & Answers section.

Learn more
Download our step-by-step troubleshooting guides app available for both iOS and Android or browse through our desktop version.

Learn more
Access the industry’s largest online wiring diagrams & photo database. A free token is provided in every EVO-SERIES box.

Learn more
You did not find the information that you were lookingfor? Ask us a question by filling out the technical support form request. A product specialist will answer you shortly.

Learn more
From state-of-the-art vehicle remote control and connectivity solutions to premium technical support, learn why you should choose Fortin products.

Learn more

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue