Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

User

Angel Enriquez

Joined on the:

Jun. 25, 2017

Score

440

Comment(s)

7

Voted question(s)

0

Voted answer(s)

2

Votes up

0

Votes down

2

Votes up received

0

Votes down received

0

Recent Activity

Question(s) asked

5

Answered question(s)

1

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask a question
RECENT ACTIVITY QUESTION(S) ASKED ANSWERED QUESTION(S) COMMENTED QUESTION(S)

26/10/2021

 Dodge Angel Enriquez (440Pts.)

0

Automatically goes into valet mode while driving

Recently i have noticed that while driving randomly at no precise intervals and regardless of moving or stationary alarm chirps. I found this was the alarm going into valet mode. And regardless if it is already in valet mode it will do it again sometimes minutes later and sometimes 20 minutes later. So far it has never happened right after starting up. The alarm i have is a compustar with the Evo All. Any info or advice is appreciated. Thank you for your time.
Login to reply View 1 answer(s)

01/03/2020

 Dodge Angel Enriquez (440Pts.)

0

2013 Dodge Journey automatically unlock when pressing lock button

reinstalled after finding a loose wire and system was working off and on. After reinstalling the alarm, compustar CM600-AS, it is workingfor the most part however now when i press the lock button on the Compustar remote it locks and a second or 2 later it unlocks but alarm is still set. when i press unlock i can hear it pulse twice to unlock. previously i had done the standalone installing and for the most part had no issue with the exception of the loose wire but this time went with the standard installation. confirmed all the wires are connected correctly and date protocal is correct. i am sure it is a setting just not sure which one i will need to turn on or off. any help will be greatly apprciate it.
Login to reply View 1 answer(s)

21/04/2018

 Dodge Angel Enriquez (440Pts.)

0

Remote start not working

I was able to program the evo and connect it to my Compustar alarm. It now locks and unlocks through alarm. But when i try to use remote start it turns on ignition to run position but does not start. If i open door it turns off the ignition like it is suppose to. Guessing that is a setting in the programming but not sure which one.

this is for a 2013 dodge journey sxt push button and using a compustar CS6900-AS

Login to reply View 1 answer(s)

14/04/2018

 Dodge Angel Enriquez (440Pts.)

0

Programmig not working stuck at step 9

i have double and triple checked my wire connections but when i try to program my THAR-CHR6 and when i get to step 9 the light will not change from Red to blue. I have attempted this multiple times and have followed all the steps so i am lost and really could use some help. Could it be an issue with my unit or is there a trick to this i am missing. I am installing on a 2013 Dodge Journey Push button ignition. *Update* I had intially started i had updated my Evo to the most recent firmware not in beta. I downgraded to 74.22 and was able to get to the next step where the blue light would come on but it would not flash. Flashed it again to a higher FW believe 74.25 but same thing blue light doesn't flash. Otherthing i noticed is on the ODBII port guide says the CAN high wire is brown but there are no brown wires on that harness. The CAN low matches the yellow though.
Login to reply View 1 answer(s)

11/04/2018

 Other Angel Enriquez (440Pts.)

0

Vehicle unlocked not showing

I used my activation code and was able to see vehicle i entered and now that i return ti site says i have to either subscribe or use activation code to see same vehicle. Is there any way to correct this? It doesn't say anywhere there is a time limit for the activation code that camr with my fortin bypass.
Login to reply View 1 answer(s)

06/01/2018

 Dodge Dan Barendregt (130Pts.)

0

Can the parking light wire be hooked up to another source?

I have a 2010 Ram 2500 with gas engine. I have a set of Rock lights underneath my truck for an awesome look when it is parked. Can I hook up the Signal wire from the 20 pin harness of a EVO-CHRT4 to these lights instead of to the parking lights? these Rock lights draw 4.5 amps. Could I connect the signal wire to the ground of these rock lights?
Login to reply View 1 answer(s)

No results

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask a question

TECHNICAL SUPPORT

Search through our most popular products and installation topics available in our Question & Answers section.

Learn more
Download our step-by-step troubleshooting guides app available for both iOS and Android or browse through our desktop version.

Learn more
Access the industry’s largest online wiring diagrams & photo database. A free token is provided in every EVO-SERIES box.

Learn more
You did not find the information that you were lookingfor? Ask us a question by filling out the technical support form request. A product specialist will answer you shortly.

Learn more
From state-of-the-art vehicle remote control and connectivity solutions to premium technical support, learn why you should choose Fortin products.

Learn more

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue