Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

25/08/2022

 Ford Joe Allison (220Pts.)

0

2017 EvoOne with TharFor3 T harness, blue light won't blink on programming

Thank you in advance for any help! I am a long time using of the EVO ALL and have done a few EVO ONE. A bit stumped on my 2017 F150 though. Using EVO ONE with the THAR FOR 3 harness. All plugged in. Following wiring diagram for the A1 and A16 (put them together) on the white 20 pin connector. When I go to program it, I can't get it to "blink blue". Therefore, I can't get any further in the programming procedure. Followed the directions in the Guide. What could I be missing? Joe
Login to reply View 1 answer(s)

09/03/2018

 Ford nate faldet (180Pts.)

0

CRIMESTOPPER RFALL642W Is not allowing key fobs to program.

The 2 way fob setup is following the setup through the step where the Evo-all module is red yellow and blue while the key is turned to the on position. The antenna is supposed to be flashing rapidly but instead flashes intermittently and sporadic. The fobs are programmed by pressing the “-“ then the lock button, the “-“ button shows the green light flashing then when the lock button is pressed it flashes blue thena red light with a single tone. 

 

Options I have selected 2008 Ford Escape hybrid. 

A1-11


C1

D1 D1.7 D4

G

G1 G2

H2

Login to reply View 1 answer(s)

28/02/2018

 Ford David Nguyen3 (260Pts.)

0

2011 ford F150 (evo-for1) can't program module cont.

 

001A06 726984

 

Further to my other post, http://fortin.ca/en/qa/82485/2011-ford-f150-evo-fort1-cant-programing-unit

I have tried to do what Robb suggested.  I’ve followed all the steps (red connector [D] NOT plug in) , however I was able to make it to step 8 (a) when  Blue & Red Led flashed 10X, Wait, wait , and wait FOREVER, NO Blue LED flash.  (HOW LONG SHOULD IT TAKE for the module to switch to flashing blue?)

I gave up and  Turn off the key and try again 3X no luck, when and reset the evoall, re-flashed, NO luck neither .

Follow the troubleshoot, swap C3&C4 location {Can hi, low} , still the module did not program, can’t pass step 8A.

Also every time I tried programing the Evo with the RED connector plug-in, the ignition keep latched.

I am really stuck now, Any help is greatly appreciated. 

Also i forgot to mentioned, I have tried to reflash the module to a Stand Alone (3X lock) and the programing still didn't get pass step 8A.

Also the service number above has F2 which is now on. 

 

​This evo-for1 will be feeding the compustart CM5000. 

 

 

Login to reply View 1 answer(s)

25/02/2018

 Ford David Nguyen3 (260Pts.)

0

2011 ford f150 (evo-fort1) can't programing Unit

Module is not programming correctly. ( can't get pass step 7)

​etc..
Blue and red lights come on.
First key goes in. Blue, red lights on.
First key out. Blue and red

Second key in. Blue, red  lights on.

Second key out. Blue and red

First key goes back in. wait, and wait .... (STEP 8)NO Red and blue 10X flashes.

Note: once the i completed up to step 7. the ignition of the 2011 Ford f150 thinks the key is still in and on the "ON" positon (blower and dash lights are ON even after key out).

 

Vehicle 2011 ford 150 XL std key

 

Login to reply View 1 answer(s)

29/12/2017

 Ford Jon Mortrud (130Pts.)

0

2002 Ford Focus / Key-Override-All / Will Not Program

Installed a Key-Override-All with a Crime Stopper 'CoolStart RS4-G5'. The Crime stopper works great with a key in the ignition only to satisfy the transponder. I have tried several time to program the Override unit with no success. I am using Connection (1) with the Data Link. The RX,TX and IGN wires are connected directly to the ignition switch transponder. The Blue wire is connected to the Yellow/Black on the Crime Stopper (Ground When Running (Bypass Module). I am using Program (2). I press the programming button and plug in the 'Black Connector' and the (6) pin connector. The red light comes on. I than program the keys and than hit the remote start. The red light blinks (3) quick blinks and thats it. The car never remote starts with teh 'Override' however the car will remote start and perform predictably as long as there is a PATS key in range of the transponder ring give me the understanding all is will except the 'Override' module. Can you tell me what I am doing wrong?
Login to reply View 1 answer(s)

03/12/2017

 Ford James Franks (180Pts.)

0

AX-RF2 - antenna LED won't flash and remotes will not program

I've installed an AX-ONE on my 2015 Ford Focus and it works properly off of the factory remotes. I'm adding the AX-RF2 universal antenna with 2 remotes to the system. Previously I asked a question about the need to change programmed function settings using the Flash-Link to allow for programming the remote/activating the antenna. I received a reply stating that I do not need to change any program function settings. The problem that I am having is that the antenna LED never lights up and I have not been able to program the remotes. I've tried looking up installation instructions for the AX-RF2 without any success. I found the instructions and manual for the FTX44-2W and RF442W (which appears to be the same unit under the EVO name brand). It appears that I only need to plug in the AX-RF2 antenna into the AX-ONE's (4 PIN) Data-Link antenna port and then go through the programming steps that I've listed below: 1: Turn ignition On 2: Turn ignition Off 3: Turn ignition On 4: Antenna LED "should" turn On (but doesn't) 5: Press Brake Pedal 4 times 6: Press & Release the {-} button then the {Stop} button on each remote 7: Turn ignition Off Am I missing something or using the wrong instructions?
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue