Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

03/01/2025

 Ford Bob Schurdell (130Pts.)

0

Autostart works only when the key is in the car

I installed EVO fort4 kit in my 2012 Ford Fusion. I used my two factory keys and programed them per the instructions. The auto-start worked for about two months. Now it will only start when I have the key inside the car ( it does not need to be in the ignition) The key works to unlock and lock the car normal. Can you tell me what I need to do to get it working again?
Login to reply View 1 answer(s)

13/11/2024

 Ford mobilesolutionsar (280Pts.)

0

2017 F350 Super Duty Evo all 1 key programmed successfully but won't remote start

Upon trying to remote start the red and yellow come on and blue blinks 1 time but not start. Stick key and turn forward, yellow light comes on. What am I missing?
Login to reply View 1 answer(s)

29/10/2024

 Ford madman6673 (130Pts.)

0

2004 Ford explorer not seeing inputs from lock

I installed my EVO-One and was trying to program it to see the keys and this is when i first noticed that the evo was not seeing the inputs from the factory key lock and unlock, luckily i was able to get around it by starting the car with the key, and it accepted it, so further down the road i now have it fully programmed and installed, i turned on the feature that when you start the car and step on the brake it locks the doors, which it does, then when you shut the car down the doors unlock, which it also does, so the Evo is able to control the locks fully, but it is unable to see the command from the car, do i have to have a seperate remote because i really don't wish for that, am i missing something? like i said it sees the car start, it sees it shut down it controls the locks fully, but when i push the button the evo doesn't respond to the inputs at all. is it a setting that i messed with by accident?
Login to reply View 1 answer(s)

14/01/2024

 Ford skylinewindowtinting (600Pts.)

0

EVO-ALL WILL NOT PROGRAM WITH THE 2 KEY SET UP

I HAVE A 2013 FORD EDGE KEY START VEHICLE THAT WILL NOT PROGRAM WITH THE 2 KEYS. I'VE TRIED IT SO MANY TIMES. IS THE MODULE SET UP RIGHT? WHEN I GET TO STEP #8 THE LED'S DON'T FLASH I'M USING A {THAR-FORD1] HARNESS. S/N 001A07270913 THANKS.
Login to reply View 2 answer(s)

14/01/2024

 Ford skylinewindowtinting (600Pts.)

0

EVO-ALL WILL NOT PROGRAM WITH THE 2 KEY SET UP

I HAVE A 2013 FORD EDGE KEY START VEHICLE THAT WILL NOT PROGRAM WITH THE 2 KEYS. I'VE TRIED IT SO MANY TIMES. IS THE MODULE SET UP RIGHT? WHEN I GET TO STEP #8 THE LED'S DON'T FLASH I'M USING A {THAR-FORD1] HARNESS. S/N 001A07270913 THANKS.
Login to reply View 2 answer(s)

22/08/2023

 Ford jaber awadh (340Pts.)

0

f150 2016 just start once

hello i installed a evo all for3 for f150 2015. the firmware 4.01 i done the program and everything good but the car just start once when i start it again the car doesnt start just the car alarm start once.

i checked the hood every thing good the car came with hood pin. 

the SN: 001A07 390594

 

this my customer car i need help please 

 

Login to reply View 1 answer(s)

10/02/2023

 Ford Kevin Pearsall (130Pts.)

0

Remote start programming issue

I have a 2000 ford excursion with the 6.8 v10 and I have just installed a mpc remote start kit number 4232. After installing by soldering in a bunch of wires I got to the key programming stage where a fortin instruction page is included and I follow the steps it says but the red light on the key override all module won't blink the 10 times like it says it should. If I plug the antenna in it will put the truck into run mode and begin trying to crank the motor but will not fire leading me to security issue because the key won't program. The instructions say for the ignition switch connector I should have connector H but in reality I had connector C so I connected the tx and rx wires as instructed but I am confused to where to go next
Login to reply View 1 answer(s)

27/10/2022

 Ford Richard Gillingham (130Pts.)

0

2013 F-150 not starting after EVO-All Installation

After the installation, I programmed and everything went perfectly. I Had it set to 3 locks to start. Now it turns on the ignition and tries to start, but there is nothing. It's as if we are trying to start with an unprogrammed key. I went back over all my connections and everything seems fine. I also found a little note on your site about disabling option D2. I've done this but still have the same condition. Any help on this matter would be most appreciated. Thanks
Login to reply View 1 answer(s)

23/10/2022

 Ford Trevor Voitik2 (130Pts.)

0

Ignition turns on but won’t crank

I just my oem remote and the trucks ignition turns on but it won't start the hood pin is disabled as I don't have one on my truck 2009 f150
Login to reply View 1 answer(s)

25/08/2022

 Ford Joe Allison (220Pts.)

0

2017 EvoOne with TharFor3 T harness, blue light won't blink on programming

Thank you in advance for any help! I am a long time using of the EVO ALL and have done a few EVO ONE. A bit stumped on my 2017 F150 though. Using EVO ONE with the THAR FOR 3 harness. All plugged in. Following wiring diagram for the A1 and A16 (put them together) on the white 20 pin connector. When I go to program it, I can't get it to "blink blue". Therefore, I can't get any further in the programming procedure. Followed the directions in the Guide. What could I be missing? Joe
Login to reply View 1 answer(s)

23/07/2022

 Ford CHRIS TZ (130Pts.)

0

remote-start-not-working - evo rs THAR-FOR3 T HARNESS

PROGRAMED MODULE FOR 2016 MONDEO (AUSTRALIA) PUSH TO START BUT CAR IS NOT STARTING. UPON PRESSING ROMOTE FOB 3 TIMES MODULE LIGHTS UP SOLID RED AND YELLOW, BLUE LIGHT BLINKS TWICE AND HEAR CLICK FROM MODULE AND THEN THE RED LIGHT BLINKS 3 TIMESBUT NO START. HAVE ACTIVATED REMOTE START FEATURES WITH FORSCAN CAR HAS FACTORY HOOD SWICTH AND ALARM SN 001A07 331144
Login to reply View 1 answer(s)

11/04/2022

 Ford chris haskins (130Pts.)

0

Why is my new Fortin Key W642 lock&unlock are backwards drivers door saying ajar some interior lights staying on?

I have a 2012 F150 that i installed a EVO-All with the Fort1 t harness as standalone remote start and W642 RF kit add on, also wanted to use alarm feature on it. I contacted suport and they set it for me as far as the option go that were uploaded tio the EVO-All from my computer. So truck will remote start with OEM fob and aslo Fortin W642 foib. OEM will unlock and lock like it should but the Fortin W642 whn i press lock it send a unlock comand and when i press unlock it does nothing. Parking lights do not flash but i hear the relay clicking like it has a issue. i Need some help ive been going over wire that ive connected and it looks correct. I double checked the direction the ! amp diode is istalled and it aslo seems right. I went to the store today and grabbed a few ne diodes to try that......Ok so i went out to truck to check somthing and i cut the wire for the door pin when i 1st installed as stated i wanted to use the alarm feature but when checking it with my meter. even though the wires are cut its showing 0.0 ohms like it is still connected or grounded out somwhere. Please ask me anythying i dont care how stupid you think the question is i just need to get this thing fiuxed. My wife is starting to hit me with the "I told You, You shouldn't put that on your truck!" 

 

Login to reply View 1 answer(s)

11/01/2022

 Ford Connor Hammond (140Pts.)

1

Evo All setting off intrusion alarm and not starting car

I installed a prewired evo all into my 2018 Ford Escape. All programming went just as the instructions said and both factory keys successfully programmed. When I go to tripple lock the car the start it, the accessory power turns on, then the intrusion alarm goes off and the car does not start. How can I resolve this issue?