Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question

0

Outlander 2022 with Fortin EVO One - remote start does not always work when using RFK942

Hello, 

When pressing the remote start button on the RFK942 key fob, the remote start does not always activate. When this does not happen, the car behaves differently: the marker lights come on along with the low beam headlights for a couple of seconds, then everything goes off. However, when the remote start command is successful, the low beams do not activate, the turn signals come on for half a second, followed by the marker lights. Additionally, there seems to be a door lock click, then the engine starts, which can be seen in the video. https://youtube.com/shorts/B6o0cWfPQQo

Remote start with the factory key, activated by three presses on the lock button, does not cause any issues with the remote start.

The flash-link 4 has version 5 firmware, vr. 4.08. An additional impact sensor and siren are installed.

There is also an issue where if the car is armed or started with remote start, if the trunk door is opened with a sweeping motion from below (via the sensor), the siren starts making noise. If opened with the button on the door, everything is okay.

Thank you for your help!

0

intermittent crank no start 3 parking light flashes Mitsubishi Eclipse 2012 with oem alarm

This is driving me crazy... It works and then it does not... Need some help please.

Everything is connected per instructions (Guide # 24871), except; I had to disconnect the (A8 dk. blue) to Driver Door pin, as it left the Door ajar on constantly. 

The Yellow loop has been cut on the fortin unit.

Fortin unit SN: 002B04 251304

Crank no start and 3 parking light flashes. 

When Press lock from OEM keyfob nothing flashes in the fortin unit.

 Setup in Flash link:

Bypass

Firmware 86.05

Hardware inside 4.0

A1 on

A2 off

A3 on

A4 on

A5 on

A6 on

A7 on

A8 off

A9 on

A10 off

A11 on

B1 on

C1 on

D2 on

D3 off

D4 off

D5 on

D6 off

E4 off

E5 off

 

Remote start

Firmware 1.26

Hardware inside 7.0

2 off

3 1

4.1

6.1

7.1

8.1

9.1

10.1

11.1

11.4

12.1

13.2

14.1

15.1

16.5

18.1

19.1

20.8

21.1

24.1

25.6

26.1

29.1

30.1

31.4

32.5

33.1

35.2

36.2

37.1

38.1

39.2

0

intermittent crank no start 3 parking light flashes Mitsubishi Eclipse 2012 with oem alarm

This is driving me crazy... It works and then it does not... Need some help please.

Everything is connected per instructions (Guide # 24871), except; I had to disconnect the (A8 dk. blue) to Driver Door pin, as it left the Door ajar on constantly. 

The Yellow loop has been cut on the fortin unit.

Fortin unit SN: 002B04 251304

Crank no start and 3 parking light flashes. 

When Press lock from OEM keyfob nothing flashes in the fortin unit.

 Setup in Flash link:

Bypass

Firmware 86.05

Hardware inside 4.0

A1 on

A2 off

A3 on

A4 on

A5 on

A6 on

A7 on

A8 off

A9 on

A10 off

A11 on

B1 on

C1 on

D2 on

D3 off

D4 off

D5 on

D6 off

E4 off

E5 off

 

Remote start

Firmware 1.26

Hardware inside 7.0

2 off

3 1

4.1

6.1

7.1

8.1

9.1

10.1

11.1

11.4

12.1

13.2

14.1

15.1

16.5

18.1

19.1

20.8

21.1

24.1

25.6

26.1

29.1

30.1

31.4

32.5

33.1

35.2

36.2

37.1

38.1

39.2

0

PUSH TO START SAMRT KEY

Hello Does anyone know how to test the starter wire on the ECM plug of a 2017 Mirage? Does it have 12V and drops on crank like on a standard key, or is it different.

0

Outlander remote start not working

2007 Mitsubishi Outlander Standard Key. Using EVO ONE and RF641W. The module and fobs are programmed correctly. Using the RF641W will not lock the doors right away, but will lock after about a minute. The unlock function works and the remote start does not work. I press the start button for 3 seconds and it unlocks the car, the blue light on the module flashes and the remote flashes. The car does nothing but sit there and after about a minute the doors lock.

0

Remote start does not work.

Hello, Mitsubishi Eclipce Cross 2018, PTS. EVO-All (hw v.7; fw v.86.01) + RF642W. ON: A1-A4, A7-A11, B1, C1, D1, D1.6, D1.10, D6, H2. Dcryptor - ok. PROGRAMMING REMOTE TRANSMITTERS - ok. With remote start by OEM remote or the RF-kit remote error is displayed "ELECTRICAL SYSTEM SERVICE REQUIRED". Help please. EVO-ALL
SN: 001A07 004370  

0

Remote start doesn’t do anything

I have a 2017 Mitsubishi Mirage Hatchback manual transmission with the standard key. I have an Evo-One installed according to the wiring diagram listed on this site. After a firmware update was performed on the bypass, I updated the firmware on the remote start portion of the unit. I then programmed it into the vehicle, went back to the computer and sent the information through to generate a key code. I reinstalled the unit in the car and when performing a remote start, nothing happens. The vehicle only reacts as if the car was not equipped with an additional device. I only hooked up the wires as shown in the install guide, nothing additional. Should I have hooked up others? Please help. Thanks.

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue