Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

29/10/2021

 Toyota Eric Bridgemohansingh (160Pts.)

0

Evo start with analog install on Evo one?

I was looking to install Evo one starter with alarm with Evo start on my 98 4runner I know my vehicle is not listed but with analog installation of Evo one this should work no problem I just wanted to know if the Evo start is able to work with a analog system and if I can still add an aftermarket RF kit like the compustar G15 RF kit?
Login to reply View 1 answer(s)

16/01/2018

 Toyota bill dougherty (160Pts.)

0

2010 4 Runner evo-all wont program

I have connected an evo-all, firmware 79.43 with a crimestopper remote start on a 2010 toyota 4 runner with a g labeled key. Connecting at obd2 violet wire (can high) white wire (can low) and green wire (immo data). Once I get to step 5 of programming the evo-all only flashes red. Are there any other can high, low and data wires?
Login to reply View 1 answer(s)

29/12/2016

 Toyota Jakub Fidler (130Pts.)

0

Dual EVO-ALL modules and external RS - 2015 Toyota 4Runner Ltd w/PTS

I'm looking to gather some information regarding for an installation into a 2015 Toyota 4Runner Limited w/PTS. Since the EVO-ALL, when used for remote start with take over can only be used with an external remote starter module, it seems all of it's CAN-BUS functions must be disabled, and it is restricted to bypassing the IMI/IMO authentication of the vehicle. As a result, none of the monitoring options such as in standalone mode, or external RS mode w/out takeover are available. Can I wire a second EVO-ALL unit to my R/S (Viper 5706v) in external R/S mode w/out takeover to function as the interface between the CAN-BUS system and the R/S? This bypass would have the immobilizer functions disabled of course, since the first module would be handling that function. Visually represented, it would be: VIPER 5706V ----(directwired)----- EVO-ALL #1 in external R/S w/takeover for PTS | ----------------------(d2d)----------------EVO-ALL #2 in external R/S WITHOUT takeover The reasoning for this is to maintain the following: 1. Remote start with 1 mile range with full takeover capabilities 2. Interface with smartkey system to unlock doors, disarm, etc. Thanks for any answers you can provide.
Login to reply View 1 answer(s)

06/01/2015

 Toyota Michael Rudy (190Pts.)

1

Evo One lights up YELLOW when I plug in 20 pin connection on bypass programming

2014 Toyota 4Runner G Key using Toyota 1 T harness and Guide #18251 I'm performing the Key Bypass Programming Procedure and can get the Blue and Red light to come as instructed, but as soon I plug in the 20 pin connector the YELLOW light comes on and i can't get the bypass to program. Thanks, Mike
Login to reply View 1 answer(s)

17/12/2014

 Toyota brent hatfield (130Pts.)

0

how to check can-bus 2014 4runner

I have installed the evo one, all the connections are good (wrapped not t-tap'd) and correct according to the installation guide. The firmware is set at 79.24 however the unit will not respond to the truck, from searching i see that a blue light will flash when there is can activity. If i hit lock/unlock there is no blue light. Its not a vehicle problem because this is replacing a flcan and audiovox remote start which was working when uninstalled. It will program, flash's blue and red x10 and the blue fast flash with no issues. I tried backing the firmware up to 79.18 and still it does the same thing, reset and reprogrammed it. I get a yellow light with ignition but no other lights. I do have a flash module, the oem control is enabled from the bypass side and 3x start is enabled from RS side. This is a G-Key truck, NOT push to start.
Login to reply View 1 answer(s)

09/12/2014

 Toyota Micheal Unger (2680Pts.)

0

Check Engine Light 2010 4runner

Hello, installed CT-3471TW Prostart remote starter with D2D EVO-ALL into 2010 Toyota 4Runner. Unit worked great, sent home with customer, Vehicle has check engine light that night, code P0705 "transmission range sensor A circuit". Used wiring guide provided from "wirecolor" and guide #8971 for Evo-all. If I clear fault, drive vehicle around- is fine. start with remote starter, key takeover, put in reverse, CEL and Traction control light illuminate on dash. Checked wiring connections at ignition switch, IGN 1- black pin6, Ign 2 purple pin 4, starter 1 red pin8, starter 2 black pin2. For the extra starter wire i used a standard relay, pin 85 ground, pin 86 to starter 1, pin 30 to +12v. pin 87 to starter 2. Any ideas? Thanks, Mike.
Login to reply View 3 answer(s)

09/12/2014

 Toyota Micheal Unger (2680Pts.)

0

Check Engine Light 2010 4runner

Hello, installed CT-3471TW Prostart remote starter with D2D EVO-ALL into 2010 Toyota 4Runner. Unit worked great, sent home with customer, Vehicle has check engine light that night, code P0705 "transmission range sensor A circuit". Used wiring guide provided from "wirecolor" and guide #8971 for Evo-all. If I clear fault, drive vehicle around- is fine. start with remote starter, key takeover, put in reverse, CEL and Traction control light illuminate on dash. Checked wiring connections at ignition switch, IGN 1- black pin6, Ign 2 purple pin 4, starter 1 red pin8, starter 2 black pin2. For the extra starter wire i used a standard relay, pin 85 ground, pin 86 to starter 1, pin 30 to +12v. pin 87 to starter 2. Any ideas? Thanks, Mike.
Login to reply View 3 answer(s)

09/12/2014

 Toyota Micheal Unger (2680Pts.)

0

Check Engine Light 2010 4runner

Hello, installed CT-3471TW Prostart remote starter with D2D EVO-ALL into 2010 Toyota 4Runner. Unit worked great, sent home with customer, Vehicle has check engine light that night, code P0705 "transmission range sensor A circuit". Used wiring guide provided from "wirecolor" and guide #8971 for Evo-all. If I clear fault, drive vehicle around- is fine. start with remote starter, key takeover, put in reverse, CEL and Traction control light illuminate on dash. Checked wiring connections at ignition switch, IGN 1- black pin6, Ign 2 purple pin 4, starter 1 red pin8, starter 2 black pin2. For the extra starter wire i used a standard relay, pin 85 ground, pin 86 to starter 1, pin 30 to +12v. pin 87 to starter 2. Any ideas? Thanks, Mike.
Login to reply View 3 answer(s)

21/10/2014

 Toyota Marc Voyer (920Pts.)

1

Stand Alone Evo All 4Runner 2013

I just made an install of a stand Alone Evo All on a 2013 4Runner Push to start Programming went as told in instruction Hardware 6 79.11 Monitor oem remote selected stand alone evo all selected. Car flashes the 4 ways each time I press lock, red led come on on evo parking lights come on at some point after i clic 3 times then go out then come back on ( I suppose the off time is when car should be cranking ) then parking light goes out and red led goes out. I saw blue led react each time I press lock on oem smart key. At my evo module, If i turn on car ignition i do have power to yellow wire and steering lock volt does go to ground. BUT when i remote start 3 x lock I don t see my steering lock signal go down (dvom) I don t see ignition power coming on (dvom)
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue