Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

30/12/2023

 Chrysler Amin Bakri (210Pts.)

0

programming

intalling EVO CH5 on my 2009 Chrysler Sebring. When i go to progam it to the vehicle i press the black button and plug the black connector with igition off. All 3 LEDs flash at the same time and will not go to just blue like it says it is supposed to program. I cant find the trouble shooting section to find answers
Login to reply View 1 answer(s)

28/12/2023

 Honda KaPa (320Pts.)

0

EVO-one is not going to programming mode

Hi,

Im having trouble getting Evo-one to go pairing/programming mode to re add Omegalink remote which stopped working. It worked beginning of the year, but not anymore.

What I have tried:

Valet Switch

    Ign on. Hold valet switch until red led flashesPress 5x. Led flashes everytimePress 1x brake pedal. Led flashes once
As i understand from the instruction, it should start to flash again to be in pairing mode. But it just flashes once from pushing pedal.Brake pedalUsed it to set up system beginning of the year and all worked. Now doesnt do anything. Actually using brake pedal when setting up Omega antenna also flashed as I pushed the pedals.Can you please help me with the next course of action. Right now system is not working for me as oem remote does not reach my car.Just fyi
    I did change settings on tack time because with cold weather my car wouldnt startFor omega correct firmware 0.44 is on Evo
Login to reply View 1 answer(s)

17/12/2023

 FAQ Joshua Swenson (1660Pts.)

0

Changing options after installation

Hi all, Just wondering if there is a general rule as to what needs to be unplugged if we need to change options on a module (EVO-ALL or EVO-ONE) without removing it from the car? Just the 4-pin cable? Remove all of the cables? I'm going to be adding an RF-kit and will need to change that setting. Thanks
Login to reply View 1 answer(s)

04/11/2021

 Chevrolet Carlos Paige (750Pts.)

0

I have 3.4v going to brake wire when vehicle is switched on.

Evo One installed on 2005 Avalanche. I have 3.4v at the brake wire when the vehicle is switched to on position. This won't allow the module to start or program rf kit. Is there a resistor I can install on the brake wire to remedy this, or try to locate a different wire to splice into?
Login to reply View 2 answer(s)

04/11/2021

 Chevrolet Carlos Paige (750Pts.)

0

I have 3.4v going to brake wire when vehicle is switched on.

Evo One installed on 2005 Avalanche. I have 3.4v at the brake wire when the vehicle is switched to on position. This won't allow the module to start or program rf kit. Is there a resistor I can install on the brake wire to remedy this, or try to locate a different wire to splice into?
Login to reply View 2 answer(s)

23/06/2021

 Jeep Steve Floyd2 (1960Pts.)

0

2011 Wrangler 3X Lock remote start with evo All with add on locks

Hi i have a 2011 Jeep Wrangler I put in add on locks with remotes kit and want to install Evo All 3x lock remote start. I have a PAC TR-7 universal trigger output module to use but not sure how to get it to all work. I have universal RF crime stoppers remote kit for evo All that I am adding to the evo All. What wiring setup chart should I use? Thanks Steve
Login to reply View 1 answer(s)

11/02/2021

 Nissan shaneywill (170Pts.)

0

Add Viper Responder LC3 4706V

So I was trying to see what is the best viper remote starter that would work with my fortin remote start? I want the led remote so I see if anything is happening to my car why it's on
Login to reply View 1 answer(s)

01/02/2021

 FAQ shawn hope (180Pts.)

0

evo-all doors lock unlock when I moved it to add RF

Went to remove the unit to add rf and the doors locked and unlocked when I touched the evo-all. Removed from truck. Is there a options menu in the newest software because I could not find it? I selected rf and flashed. Instructions say to go into options. Thanks
Login to reply View 0 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue