Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

22/12/2023

 Audi Scott Edlin (130Pts.)

0

Audi 2013 S4 DSG - Fortin ALL getting stuck on step 7 with 3 x red flashing lights

Just installed a Fortin ALL with the Audi T Harness on a 2013 Audi S4 DSG. UK right hand drive car. When I go to try and get the unit to read the key data I am just getting 3 red light flashes on step 7, everything is fine up until that point and the car operates as normal. When I then put the flashlink back onto the PC software it says invalid key data. Any ideas? I have checked all wiring, also checked status of CANBUS with zero issues showing so I know that wiring is good. Serial no for module is : 001A07445150
Login to reply View 1 answer(s)

06/04/2022

 Infiniti Luis Sanchez2 (950Pts.)

0

RFK942 Remote LED

When I start my G37S which uses the RF642W remote, the RF642W remote's green LED flashes once every six seconds when the car has been started remotely. On my Q50, which has the RFK942, when the car has been started remotely the LED of the RFK942 remote flashes once every 10 seconds. My question is, is there is a way to change how often the LED on the RFK942 remote flashes? This trivial and certainly no "deal breaker" since I do preferrer the RFK942. I was just wondering.
Login to reply View 1 answer(s)

01/02/2020

 Ford Todd Aker (200Pts.)

1

Can not get past step 6 no blue light in step 7

I have a 2010 ford escape. auto trans and 6cyl engine. I can not get the blue light to light for step 7. Checked all the can connections and even solidered them. they are correct as the instructions ask them to be. HELP?
Login to reply View 2 answer(s)

01/02/2020

 Ford Todd Aker (200Pts.)

1

Can not get past step 6 no blue light in step 7

I have a 2010 ford escape. auto trans and 6cyl engine. I can not get the blue light to light for step 7. Checked all the can connections and even solidered them. they are correct as the instructions ask them to be. HELP?
Login to reply View 2 answer(s)

08/07/2020

 Buick Mohamed Ali (460Pts.)

0

Rfk 912 antenna

I have rfk912 kit with antenna, the antenna led usually gives blue light, but sometimes specially when the car is left for a while , when i come back i find it very faint red color? What does this means ?
Login to reply View 1 answer(s)

01/02/2020

 Ford Todd Aker (200Pts.)

0

Can not get past step 6 no blue light in step 7

I have a 2010 ford escape. auto trans and 6cyl engine. I can not get the blue light to light for step 7. Checked all the can connections and even solidered them. they are correct as the instructions ask them to be. HELP?
Login to reply View 0 answer(s)

23/01/2020

 Toyota Norman Fennych (460Pts.)

0

Antenna light blinks constantly when truck off and locked

Installed the Fortin evo one 442 kit with antenna, is the antenna supposed to blink constantly blue when truck isn't running ?
Login to reply View 1 answer(s)

11/01/2020

 Mazda Alex Macharia (130Pts.)

0

Mazda Failing Decryption process (not able to get a solid blue)

I have tried to run the exact process for initializing decryptor for a CX-9 install, starting with diconnecting the neg battery terminal and then connecting the steering wheel white terminals into the T harness,reconnecting battery power and then holding down the button on the Evo one module while plugging in the 6 pin connector. I have not been able to get the module to set the blue solid light. Anyone run into this? Module was programmed correctly via flashlink
Login to reply View 1 answer(s)

12/10/2019

 Chevrolet Kid Ratits (470Pts.)

0

Can'y get blue solid blue led

2006 chevy uplander evo one can't get solid blue led in step 1 programming
Login to reply View 1 answer(s)

12/10/2019

 Chevrolet Kid Ratits (470Pts.)

0

Can'y get blue solid blue led

2006 chevy uplander evo one can't get solid blue led in step 1 programming
Login to reply View 0 answer(s)

21/10/2018

 Mazda Carlos Henao (150Pts.)

0

No blinking blue light when programming in step 4 of install guide for a 2018 Mazda CX9.

I bought the EVO-One and the THAR-ONE-MAZ3 T-harness for a 2018 Mazda CX9. I got the t harness installed fairly easy but am having trouble programming. I hold the programming button while I connect the 6 pin main connector, release when the blue light is solid, connect the rest of harness, press on 2x but the LEDs never flash as instructed. I'm not sure how to proceed from here, I've reset the module and tried a few times. The 20 pin connector has a bunch of lose wires on the t-harness, should this be connected to anything? From my understamding only the optional parking light wires needed hardwiring, everything else was plug and play.
Login to reply View 1 answer(s)

19/11/2016

 FAQ Corey Church (170Pts.)

1

No LED's on unit after initial install

I completed all the intall wiring on my evo one on a 2007 mitsubishi eclipse, updated the bypass and remote start and when I plugged the unit in, I didn't see and LED's light up at all. Tryed to program the bypass, no LED's. removed the unit and tried to check the programming on the unit and it all seems to be fine. Looked in the Questions on the support site, and found that perhaps a master reset needs to be done. I can't seem to get any response from the unit on the car to do anything so I can't get into the programming mode to reset and can't get the red light during the master reset. What can I do?
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue