Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Utilisateur

MaddMan

À rejoins en date due:

Dec. 19, 2018

Points

310

Commentaire(s)

3

Questions votée(s)

0

Réponses votée(s)

0

Votes positifs

0

Votes contre

0

Votes reçus

1

Votes négatifs reçus

0

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez une question

02/01/2022

Audi MaddMan (310Pts.)

0

dcryptor reset - Evo-All

Can you please dcryptor reset my evo-all Service# 001A06 831101. Hardware Vr:6 Firmware Vr: 4.18 Date 05/2018 It had been remote starting in my 2014 Audi Q5 with T-harness, the past few years. I recently purchased RM411 one way remote to extend range farther than factory remote. During programming on step 5 the yellow led will not light up or the antenna blue led flashing. Not sure if RF kit setting to H2 is ok, of if this matters. Tried both H1 and H2 in setting, no difference when trying to program. Firmware: 60.10 So, I master reset the evo-all to start over with settings and dcryptor. Received error message “dcryptor limit has been reached for this car”? Any suggestions for programming RM411, after getting remote start working with factory remote?

26/12/2021

Audi MaddMan (310Pts.)

0

Connecting RF KIT RM411 to EVO-ALL

2014 Audi Q5 push button start with EVO-ALL. Remot start works with factory remote for few years. Decided to upgrade remote to RM411. During progamming on step 5 the yellow led will not light up or the antenna blue led flashing. Not sure if RF kit setting to H2 is ok, of if this matters. Tried both H1 and H2 in setting, no difference when trying to program. Firmware: 60.10

03/04/2019

Audi MaddMan (310Pts.)

0

2014 Audi Q5 evo-all T-harness invalid key data (dcryptor step)

2014 Audi Q5 w/ keyport. Evo-all with t-harness sofware 60.02 loaded suggested options C1, D2, D6. Using installion guide 77161, following steps. Leds lightup as stated in steps 1-8. During dcryptor step, states "invalid key data". I reset module and tried again with same message "invalid key data" during dcryptor step. Looking for suggestions to get dcryptor step accomplished.

28/01/2019

Audi MaddMan (310Pts.)

0

Adding Linkr LT-2 RF antenna to EVO-All

EVO-ALL (T-harness) with Linkr LT-2 RF antenna

2009 AUDI A4 with key-port, auto transmission

Step 8 . LEARN THE TELEMATIC DEVICE TO THE EVO-ALL

In order to communicate with the remote starter, the Telematic device must be learned to the EVO-ALL.

1- Disconnect the 4 pin power connector from the Evo-All.

2- Press and Hold the Programming button on the Evo-All while plugging back the Black 4 pin connector.

3- The LED’s on the Evo-All will begin to cycle. Keep pressing the programming button until the RED &

BLUE LED’s are On.

4- Release the programming button.

5- Press & Hold the programming button again for 5 seconds until the BLUE & RED LED’s comes back On.

6- Release the programming button and Cycle the ignition to the ON position.

7- The RED, YELLOW & BLUE LED’s will be ON.

8- At that same moment the RED & BLUE LED’s will blink once to confirm that the MyCar ID has been

learned to the Evo-All.

9- Cycle the vehicle’s ignition to the OFF position to Exit EVO-ALL programming


I can not get red, yellow, blue leds on after cycle ignition on. Only Red and Blue leds are on.

Selected C1, D1, H2 settings for evo-all. Not sure if I need to connect another wire from harness

So the app will not lock,unlock,start,stop.

The Linkr LT app is downloaded on phone, account created, added car. The RF antenna red, green leds are solid/connected to network.

The app antenna icon is green, voltage battery icon is green and shows voltage. Select GPS icon and shows current vehicle location.

1

EVO-ALL PROGRAMMING 2006 VW JETTA

During programming at step #7 only the red LED flashes 6 times in a row/stops/starts again, not blue/red/yellow alternating as stated. I'm using TB-VW. Using guide #63221 for wiring/programming. All connections are solder and doubled checked wiring for errors. Using firmware 75.[35], hardware 6.0. CanBus Orange wires measure 2.5 volts. Yellow ignition wire has 12 volts minimum.

No results

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez une question

Support Technique

Recherchez parmi nos produits les plus populaires et les sujets d'installation disponibles dans notre section Questions et réponses.

En savoir plus
Téléchargez notre application de guides de dépannage étape par étape disponible pour iOS et Android ou parcourez notre version de bureau.

En savoir plus
Accédez à la plus grande base de données de schémas de câblage et de photos en ligne de l'industrie. Un jeton gratuit est fourni dans chaque boîte EVO-SERIES.

En savoir plus
Vous n'avez pas trouvé l'information que vous cherchiez ? Posez-nous une question en remplissant le formulaire de demande de support technique. Un spécialiste produit vous répondra sous peu.

En savoir plus
Des solutions de contrôle à distance et de connectivité à la fine pointe de la technologie au soutien technique haut de gamme, découvrez pourquoi vous devriez choisir les produits Fortin.

En savoir plus

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer