Questions & Réponses

Having issue with starting it lights up, brake lights come on like its going to start but stops without cranking says "brake" on LCD On dash, and evo stays lit with orange light or lights , if i put a stick on the pedal and hold brake pedal down as i try to remote start, it works fine

2014 VW Jetta
FORTIN EVO-ONE W/
VWT1 T HARNESS
DATE 12/2021
s/n 002b04248922
firmware remote start = 1.[26]  hardware 7.0
BYPASS = 75.[41]
hardware 4.0
using spare key
loaded suggested options on both with diesel option checked

I talked to 1 of your techs today on the phone about it not starting at brake and he said there may be another black & red wire for the brake but after looking at the factory wire schematic & taking the plug down again and physically looking at it,  there is only 1 red & black but there is a {black& violet} & {black & yellow} after the brake switch on the schematic, so im thinking going to one of those? at this point ive tried everything else i know to do.
i watch the lights on the evo as i hit the remote start it goes through all 3 lights then after stays on 2 orange lights or 1 glowing over to look like 2? and still says "brake" on the dash as its trying 

brake lights come on as its going through the process of trying to start also

so it looks and acts like its going to but fails, checked every connection with my fluke meter also, everything is wired correctly only wire in question i suppose is the brake
and i dont care about having to press on the brake pedal so if there are wires to connect or cut to just do away with this feature im all for it to get this project done
 
P.S. I never did get a blue flash after plugging in all the plugs and turning on ignition, just lights turned off so dont know if thats normal and not mentioned in the guide? or if something is still wrong?

thank you!

https://drive.google.com/drive/folders/16x-fbU40zovZW_PALHmOfIwePzKDa5r9?usp=sharing

https://drive.google.com/drive/folders/16x-fbU40zovZW_PALHmOfIwePzKDa5r9?usp=sharing

hi, i installed a Fortin EVOALL+VIPER 4806V remote starter for my 2017 volkswage tiguan with push to start.

i use DATA-LINK wire to connect the bypass module and remote starter. so there is only a few wires need to be connected.

i flashed evoall with firmware 75.25 and the evoall programmed successfully on the car.

i didn't connect the parking light wire for the remote starter. i'm confused for the parking lights wire connection.

the fortin manual shows there should be a RS3 OUT PARKING LIGHTS(-) wire connect to a relay PIN 86.

But the VIPER quick reference install guide shows there is only: a H/4 WHITE/BROWN LIGHT FLASH ISOLATION WIRE -PIN 87a light flash relay and a H/5 WHITE PIN 30 of LIGHT FLASH RELAY

so should i use a relay to make the connection? but how? or there is a realy inside the remote starter? anyway i didn't connect the wires for the parking lights.

should i connect a hoop pin switch to make it work?

For the VIPER 4806V remote starter:

set light flash polarity to -, set horn input polarity jumper to -,

connected the H1 ,H2 wires(6 PIN connector),

Neutral safety switch plugged in and in the ON position.

door lock plug NOT plug in,

ground pin 13 black /white (-) neutral safety /parking brake input (as the manual mentioned) ---- 24PIN connector,

control center connected,

connected the pin8 * IGNITION1 INPUT/OUTPUT (8 PIN connector on viper)

For the EVOALL :

every wire connected as the manual said.

so here is the problem:

when i press the lock button , the door lock no action. i can hear one click sound coming from the viper brain.seems it wants to trigger the parking light to flash one time.

press the unlock button,door lock no action. two click sound coming from the viper brain.

press the remote start button the car wouldn't start. ignition doesn't go on. and i hear 5 click sound from the viper brain. which means :Brake wire is active .

i used a Digital Multimeter to test every wire from the car connector pin to the VIPER and EVOALL pin. all good!

reset the EVOALL module. nothing changed! took the EVOALL off the car to reflash it. i can enter every menu EXCEPT the EVO-ALL OPTIONS. Always shows unit is not connected.and stuck there.

my computer system is windows10. i tryed diffrent computers,diffrent USB port. nothing changed.