English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

02/05/2022

 Dodge keith lawley2 (230Pts.)

0

Evo one only responds when its in valet mode

Evo one s/n 002B04108567 programs correctly with 2010 dodge challenger standard key wire to wire oem key fob and blue light flashes after when pressing lock or unlock , yellow light turns on when starting the car. The problem is minutes later the unit appears to end in in valet mode , red light on the side near yellow cut wire is on. When I take the unit out of valet mode , red light turns off but I no longer receive the blue light when locking or unlocking the car with the oem fob. When I attempt to remote start the car 3x lock the eed light turns on then the yellow light turns on but the car doesn't crank at all and only attempts to try 1x even though programming is set for 2x attempts. Then I get 4 clicks or flashes from the module. I followed guide #94481 for installation and have tried the basic bear options with my flash link 2 updater on 59.02 and 74 38 and 1 25 firmwares. I notice to anytime I try to run the module on the FL updater the FL updater has to be updated each and every time with 4 05 ? Any help appreciated , no oem alarm
Connectez-vous pour répondre Voir 1 réponse(s)

19/11/2019

 Dodge Gary Uplinger (130Pts.)

0

blue light no start

i installed and programed and no start i have the T harness 2012 Dodge charger push to start when i try to start the car just the blue light comes on evey time i press the lock button on the OEM key fob and no start
Connectez-vous pour répondre Voir 1 réponse(s)

17/11/2019

 Dodge Reva Smith (130Pts.)

0

Evo-CHR6 Programing Issue

The module is not currently cycling through the various leds. The module lights up red, yellow, and blue but will not go to the all yellow for programing steps. The wiring currently hooked up is Can Low, Can High, T-Harness, Ignition, and parking lights. The kit included a valet switch and hood pin which I did not install. Does this need to be hooked up? Please help.
Connectez-vous pour répondre Voir 1 réponse(s)

07/11/2018

 Dodge Juan Higuera (130Pts.)

0

2005 DURANGO won't start?

i installed the fortin evo rs preloaded to my 05 durango using schematic H and the device makes a sound like its about to turn on the vehicle but then nothing happens. all it does is lock my doors. secondly how do i connect the diode to the key sense wire? am i suppose to bridge the diode to both the key sense and ignition one or do use seperate diodes for both wires? and on the schematic it shows that i need a seperate remote start? or where do i get the ground wire for the 4-pin datalink wire ?
Connectez-vous pour répondre Voir 1 réponse(s)

15/04/2018

 Dodge w de koning (130Pts.)

0

car start but then shutt down

my car dodge charger 2006 5.7ltr v8 evo chrt 5 t harness problem: car start with remote car start. it shutt down after 1sec.then second attempt same result. grtz
Connectez-vous pour répondre Voir 1 réponse(s)

17/02/2017

 Dodge Cesar Babino (160Pts.)

0

My Dodge Journey 2013 does not start?

Hi,   I bought a EVO ALL Service # 001A06 692577 just to connect OEM remote starter, trigger lights and door signal (shut off engine) but it does not start my car.   I connected all wires as showed in electric diagram (3 times OEM remote starter) and program it under the procedure with flash link updater but when I press 3 times in the OEM remote starter, nothing happens, the trigger lights does not turn on.   I checked led lights and each time that I press lock or unlock in the OEM remote starter, light is blue in EVO module, also when I press button (dashboard) to start, light is yellow.   The problem is like the EVO module does not send signal to start engine and trigger lights or the car is not receiving it (I think so)   Could you help me to find the problem, please.   Thank you   Cesar

 

 

Connectez-vous pour répondre Voir 1 réponse(s)

07/10/2016

 Dodge Jasen (130Pts.)

0

Remote start not working

Here is all info on what products I have, with links to the pdf's of the manuals showing what I have wired up.. All with a full explanation of what is not working, and what it does while trying to start.... Vehicle: 2008 Dodge Caliber SRT4 Fortin Evo-all with the T-harness ( just purchased the flash link updater ) Crime Stopper SP-502 with the data ports ( Evo is default ). I updated the evo-all via the flash link device to the newest firmware, and the newest update for my evo-all. I did not change any options on the evo-all except for the priority driver door unlock, and then I made sure that the evo-all knew to use the data port for evo series.... ---------------------------------------------------------------------------------------- I followed the instructions that came with the fortin evo-all first... using install directions "A" see here: ( http://fortin.ca/download/28831/evo-all_evochrt5_p20160902.pdf ) I then went to the crimestopper book and followed the install diagram in their book see here : ( http://www.crimestopper.com/cstech/library/security/security_systems/security_keyless_entry/sp-402_sp-502_ins_rev_09-28-2012_green%20kill.pdf ) its near the end shows the module and all the wiring. All options work as expected, except for the siren ( crime stopper side ) and the remote start, which I am not sure is the crime stopper or the fortin.... THe error I am getting when I try to remote start my vehicle is that the ignition is on prior to the remote start... ( this is from the flashes I get from my crime stopper ) I notice when I am in the car, the yellow light on the fortin is on and I believe the red light. ( I can take a video if need be ). I would love to praise the ease of install from the evo-all product and the wirecolor site, but at this point I am highly frustrated. It seems that there might possibly be a conflict between the two boxes, and something is keeping the car from cranking.... Please someone help. I want to put my dash back together.
Connectez-vous pour répondre Voir 3 réponse(s)

07/10/2016

 Dodge Jasen (130Pts.)

0

Remote start not working

Here is all info on what products I have, with links to the pdf's of the manuals showing what I have wired up.. All with a full explanation of what is not working, and what it does while trying to start.... Vehicle: 2008 Dodge Caliber SRT4 Fortin Evo-all with the T-harness ( just purchased the flash link updater ) Crime Stopper SP-502 with the data ports ( Evo is default ). I updated the evo-all via the flash link device to the newest firmware, and the newest update for my evo-all. I did not change any options on the evo-all except for the priority driver door unlock, and then I made sure that the evo-all knew to use the data port for evo series.... ---------------------------------------------------------------------------------------- I followed the instructions that came with the fortin evo-all first... using install directions "A" see here: ( http://fortin.ca/download/28831/evo-all_evochrt5_p20160902.pdf ) I then went to the crimestopper book and followed the install diagram in their book see here : ( http://www.crimestopper.com/cstech/library/security/security_systems/security_keyless_entry/sp-402_sp-502_ins_rev_09-28-2012_green%20kill.pdf ) its near the end shows the module and all the wiring. All options work as expected, except for the siren ( crime stopper side ) and the remote start, which I am not sure is the crime stopper or the fortin.... THe error I am getting when I try to remote start my vehicle is that the ignition is on prior to the remote start... ( this is from the flashes I get from my crime stopper ) I notice when I am in the car, the yellow light on the fortin is on and I believe the red light. ( I can take a video if need be ). I would love to praise the ease of install from the evo-all product and the wirecolor site, but at this point I am highly frustrated. It seems that there might possibly be a conflict between the two boxes, and something is keeping the car from cranking.... Please someone help. I want to put my dash back together.
Connectez-vous pour répondre Voir 3 réponse(s)

07/10/2016

 Dodge Jasen (130Pts.)

0

Remote start not working

Here is all info on what products I have, with links to the pdf's of the manuals showing what I have wired up.. All with a full explanation of what is not working, and what it does while trying to start.... Vehicle: 2008 Dodge Caliber SRT4 Fortin Evo-all with the T-harness ( just purchased the flash link updater ) Crime Stopper SP-502 with the data ports ( Evo is default ). I updated the evo-all via the flash link device to the newest firmware, and the newest update for my evo-all. I did not change any options on the evo-all except for the priority driver door unlock, and then I made sure that the evo-all knew to use the data port for evo series.... ---------------------------------------------------------------------------------------- I followed the instructions that came with the fortin evo-all first... using install directions "A" see here: ( http://fortin.ca/download/28831/evo-all_evochrt5_p20160902.pdf ) I then went to the crimestopper book and followed the install diagram in their book see here : ( http://www.crimestopper.com/cstech/library/security/security_systems/security_keyless_entry/sp-402_sp-502_ins_rev_09-28-2012_green%20kill.pdf ) its near the end shows the module and all the wiring. All options work as expected, except for the siren ( crime stopper side ) and the remote start, which I am not sure is the crime stopper or the fortin.... THe error I am getting when I try to remote start my vehicle is that the ignition is on prior to the remote start... ( this is from the flashes I get from my crime stopper ) I notice when I am in the car, the yellow light on the fortin is on and I believe the red light. ( I can take a video if need be ). I would love to praise the ease of install from the evo-all product and the wirecolor site, but at this point I am highly frustrated. It seems that there might possibly be a conflict between the two boxes, and something is keeping the car from cranking.... Please someone help. I want to put my dash back together.
Connectez-vous pour répondre Voir 3 réponse(s)

30/09/2016

 Dodge Evan Kolpack (280Pts.)

0

Need remote start to run indefinitely, not time out after 30 min

I'm trying to use the remote start (or push to start?) feature to replace my factory key. I need to prevent the vehicle from shutting off. I disable the foot brake option and was able to drive it but it died on the freeway!!! Very unsafe! - 2008 Dodge Sprinter w/ Crimestopper SP502 for remote start
Connectez-vous pour répondre Voir 2 réponse(s)

30/09/2016

 Dodge Evan Kolpack (280Pts.)

0

Need remote start to run indefinitely, not time out after 30 min

I'm trying to use the remote start (or push to start?) feature to replace my factory key. I need to prevent the vehicle from shutting off. I disable the foot brake option and was able to drive it but it died on the freeway!!! Very unsafe! - 2008 Dodge Sprinter w/ Crimestopper SP502 for remote start
Connectez-vous pour répondre Voir 2 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer