Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question

0

Solid yellow and red light

So im installing the evo all with the tb-vw module in a 2008 vw rabbit. ive been fighting with this thing for a few hours now trying to get the thing to read the key so i can use the dcryptor. ive manage to get past the setup 3 diffrent times but each time i end up with a solid yellow and red light when i apply power back to the evo all. when i go to start it, the yellow will go off then the red starts flashing and wont stop till i unplug it. any advice would be great. also ive tried factory resetting, flashing diffrent firmwares and ive now hit the limit on dcryptor and i believe im one flash away from the limit

0

Vw Jetta 2019 slow red flash step 8

Please help. Evo one on a 2019 vw Jetta up to 08-2018. I get to step 8 it the unit is not programming it flashes slow red. Followed support steps to check settings, open close door, start car and even master reset using valet 23 times... it still flashes slow red every time I try to program it. it's a manual transmission so I added the check parking brake. what am I missing? SN 002B04 131503

0

two blinks from red LED after step 11 Guide # 82421

I am using the following on a 2017 VW Golf Alltrack PTS w/automatic trans: EVO-VWT1 kit with harness, VW-TB, EVO-ALL, RF-Kit 411 and R-Link. when setting up the unit in fortin flashlink I get no other options for installatiom method than "key in a box" and when attempting to program the unit with the R-Link installed I get all the way to step 11 and then the the flashing blue light turns red, then starts blinking two red flashes, pauses, two flashes and so on. I cannot get anything to work to get past this.

0

two blinks from red LED after step 11 Guide # 82421

I am using the following on a 2017 VW Golf Alltrack PTS w/automatic trans: EVO-VWT1 kit with harness, VW-TB, EVO-ALL, RF-Kit 411 and R-Link. when setting up the unit in fortin flashlink I get no other options for installatiom method than "key in a box" and when attempting to program the unit with the R-Link installed I get all the way to step 11 and then the the flashing blue light turns red, then starts blinking two red flashes, pauses, two flashes and so on. I cannot get anything to work to get past this.

0

Why am I getting 3 red LED blinks after step 7?

UPDATE: I plugged everything in and gave it a try. Car starts right up but dies immediately. Gives me the "no key" alert. dcryptor process will not complete for some reason. 2013 Passat standard key, standalone install. EVO-ALL (2/2019), THAR-VW2, and TB-VW (1/2017). Guide 62471 SN: 001A07 008702 Flashlink Firmware: 75.39 TB-VW wired into brown transponder wire. I have all of the harness installed as directed but when I start the dcryptor programming, all goes beautifullt until the end of step 6. When I release the programming button, I don't get the rapid 3-LED alternation. The red LED just continuously blinks 3 times. I've even tried resetting the

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer