English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

19/11/2019

 Ford John Smith4 (130Pts.)

0

EVO-ALL won't update.

When I try to hook my EVO-ALL up to my computer to get the updates it tells me the device hooked up to my fortin Flash Link is not compatable..... not sure what I did wrong, it all seemed pretty straight forward... I updated the firmware on the FlashLink to 4.05 but it refuses to detect my EVO-ALL
Connectez-vous pour répondre Voir 1 réponse(s)

18/11/2018

 Ford kevin moon (130Pts.)

0

evo one bypass programming

I just recieved the evo one for my 2000 ford explorer and installed it with the rf kit. i flashed and updated it right away to most current firmwares. everything works like the remote start and door locks but wont accually start since i cant get the bypass to learn the keys. i get the red light when i pllug it in and then i go to start the 2 key procedure and the yellow light comes on. i get to the second key and by the end of the second 3 seconds for the second key the red light starts to rapidly flash and all the lights go off so i cant finish the bypass procedure. anyone know the issue here. is the module bad by chance? ive tried re flashing a few times and tried programing the keys many times and its the same thing each time.
Connectez-vous pour répondre Voir 1 réponse(s)

31/07/2016

 Ford Wyatt Francis (210Pts.)

1

EVO-FORT1 enables ignition before programming sequence finished

EVO-FORT1 for a 2014 Ford Focus SE (SFE) (Automatic Transmission) as a stand-alone installation (3x door lock start). I have the T-harness installed along with the connections to the Lt. Blue, Blue, and Yellow/Black wires on the harness. I have also connected the CAN bus signals. As I go through the 2-key programming sequence, the relay on the EVO-ALL will enable the ignition DURING the 3-second time of the 2nd key. When I remove the 2nd key and press/release the programming button, the unit never shuts off the ignition and neither the blue nor red LEDs flash. I have to remove power or the red connector from the EVO-ALL to turn off the ignition. I also tried pressing/releasing the foot brake as well.

During the programming sequence, I notice that the yellow LED will sometimes go on and then off. If I plug in the unit without putting it in programming mode, the unit will blink the blue LED if I press the door lock button.

I have been following guide #32051.

Does this indicate a problem with the unit itself, or is the pre-loaded firmware corrupt and needs to be re-programmed? (I will need to purchase a EVO Flash Link updater.) Is it a possible connection issue? Is it an issue in performing the programming sequence?

Connectez-vous pour répondre Voir 2 réponse(s)

05/07/2016

 Ford derek g (327150Pts.)

4

EVO-FORT1 wiring information

The biggest question I hear when it comes to the EVO-FORT1 combo is that the module "will not program"....9 times out of 10 it is that the 3 main connections were left out!!! So below is the 3 types of connections that are done between the evo and the t-harness.

TYPE 1 CONNECTION

In the above image commonly used on the 40 bit type systems its basically match the colors between the t-harness and the 20 pin connector. Be sure to isolate the Yellow/Black wire from the T-Harness as it is not connected.

Type 2 CONNECTION

In the image above commonly used on 80 bit systems we match the colors EXCEPT you are not connecting yellow to yellow rather the yellow/black from the t-harness connects to the yellow wire from the 20 pin connector and you isolate the Yellow wire in the T-Harness.

TYPE 3 CONNECTION

In the above image it is exactly the same as connection 2 but in addition to the Yellow/Black being connected to the Yellow of the evo-all, we are also connecting the Purple/Yellow along with the Yellow. Isolate the Yellow wire from the T-Harness.

Connectez-vous pour répondre Voir 0 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer