English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

10/02/2024

 Lincoln Dan Robertson (130Pts.)

0

2011 Lincoln MKT key bypass programming will not show red led when pressing brake pedal.

I am trying to do the key bypass steps as described in the stand alone Evo All Lincoln MKT 2010-2014 installation instructions, but getting stuck after being told to insert the oem remote (without battery) into the keyport and press and release the brake pedal to get the unit to display the red LED. The unit only continues to disply the yellow LED despite me pressing and releasing the brake pedal (waiting 5 seconds between each push) up to 50 times. I am using firmware .57, as instructed in the instructions, and have flashed the unit mutiple times. I have also reset the unit and reflashed all to no avail.
Connectez-vous pour répondre Voir 0 réponse(s)

22/12/2023

 Audi Scott Edlin (130Pts.)

0

Audi 2013 S4 DSG - Fortin ALL getting stuck on step 7 with 3 x red flashing lights

Just installed a Fortin ALL with the Audi T Harness on a 2013 Audi S4 DSG. UK right hand drive car. When I go to try and get the unit to read the key data I am just getting 3 red light flashes on step 7, everything is fine up until that point and the car operates as normal. When I then put the flashlink back onto the PC software it says invalid key data. Any ideas? I have checked all wiring, also checked status of CANBUS with zero issues showing so I know that wiring is good. Serial no for module is : 001A07445150
Connectez-vous pour répondre Voir 1 réponse(s)

14/11/2023

 Honda james harvey (130Pts.)

0

Solid red led on my evo one

When I press the programming button and plug in the 6 pin harness I get a solid red led. how can I do a full reset on the unit and start over? the sn is 002B04 310017, any help would be appreciated, thanks.
Connectez-vous pour répondre Voir 2 réponse(s)

14/11/2023

 Honda james harvey (130Pts.)

0

Solid red led on my evo one

When I press the programming button and plug in the 6 pin harness I get a solid red led. how can I do a full reset on the unit and start over? the sn is 002B04 310017, any help would be appreciated, thanks.
Connectez-vous pour répondre Voir 2 réponse(s)

09/08/2023

 Chevrolet jim stiene (130Pts.)

0

On step 6 the yellow light stays on solid, no red

all goes well till step 6
Connectez-vous pour répondre Voir 1 réponse(s)

12/12/2022

 Buick Eric McClish (130Pts.)

0

evo-gmt1 no red light no start

2011 buick regal evo-gmt1 sn001A07v253955 . Blue light flashes with door lock / unlock . oem remotes. no red light , no start. thar-gm1 rev2 harness. what is the correct wiring diagram ? at the moment brown wire to can sw pin 1. brown with white stripe to green /gray parking lights . cannot get ahold of tech
Connectez-vous pour répondre Voir 1 réponse(s)

05/06/2022

 Infiniti Charles Ong (130Pts.)

0

Red light disappears and Blue light stays solid

Hello, I have a 2015 Infiniti Q70 and when i program the module, I can get up to step 8 without any issues. When I press the brake for the second time, the red and blue light comes on, but after about 1 second, the red light disappears and the blue light stays solid. I'm unable to complete the programming of the module. Verified all connections are tight and correct. Please help!
Connectez-vous pour répondre Voir 1 réponse(s)

15/03/2019

 Chevrolet Joshua Fender (130Pts.)

0

Red and white wire came out of harness where does it go

I have a red and white wire with the connector pin on the end and it is not in a connector. One end of that wire goes to my smaller ignition t wire harness so I know it goes somewhere just dont know where.
Connectez-vous pour répondre Voir 1 réponse(s)

26/11/2018

 Chevrolet chase steele (190Pts.)

0

xtra wires? no red led when programming

2005 chevy silverado 1500 using install guide 61101 evo one. during programming blue led goes off but no red led, I have verified obdII connection. firmware is 70.21 another question is should i wire in the unlock, lock, +ign, -ign, -disarm on the 20pin?
Connectez-vous pour répondre Voir 0 réponse(s)

06/01/2018

 Mazda nicktagz (280Pts.)

0

CX-3 won't start

After the remote start fails I get 3 red blinks from the module. No tach is the code but I don't know which cable is messed up. I have the evo-all hardware ver 6. Service # 003606005190. Also I'm not sure if I have the correct setttings selected.
Connectez-vous pour répondre Voir 0 réponse(s)

16/01/2017

 Mazda Rob Rosencrans (130Pts.)

0

2013 Mazda CX-5 programming issue

Difficulty programming unit. First had issues getting the module to learn the keys but realized I had low voltage. Charged battery and went through all steps up to 25 (towards end of CAN programming). At the end of sequence I received the blue light and it went off, then waited about a minute or longer, but never received the red LED. I've been through all steps including 1-12 and starting at 17, 18 and 21 but without success, have reset and resent data, but usually only receive flashing red. How can I completely start over as the unit seems not to fully reset after master reset and only get flashing red after going through 1-12 again. What process where should I start? Thanks.
Connectez-vous pour répondre Voir 1 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer