Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question

0

2010 ford escape KEY-OVERRIDE-ALL

I'm installling the KEY-OVERRIDE-ALL with a DEI remote start. When I attempted to program prior, I would see the LED start flashing, but programming didn't complete. Now when I attempt to program, the LED on the module stays on and the security light on the dash flashes rapidly. I've confirmed I have 12V on Red, Ground on Black, Ignition on Yellow, and remote start staus on Blue. Is there anything else i should try on this module? The module was purchased new in December and hasn't been installed in another vehicle.

0

Ford Escape will not disable RAP (retained accessory power)

I have A17 and A18 spliced into the green/purple wire at driver harness, one side 0V and other side ~11V. When driver door latch manually closed the door side of harness shows 10ohms, when door open shows OL so I know I have correct wire. How should setting be flagged?

1

Evo all on 2014 ford escape will not recognize my keys.

I got the evo all thinking it was programed for my ford escape out of the box. Connected all wires it flashed ble and red. So I got a flash deal. Flashed it. Was able to get it to recognize the car, but when trying to make it recognize the keys to set up the auto start it flashes red and blue.

0

2005 ford escape does not crank ?

I installed a EVO ONE with a RF 642w . Everything works locks,unlock,alarm.. When i went to actavate the remote start the parking light comes on as if its going to crank but does not ,parking light flashes 4 times then it try's to start again and fails to crank parking lights flash again 4 times . Then it stops . please help me

0

Unreliable starting, and key left in door chime on 2011 Mercury Mariner (Ford Escape)

I installed a EVO-FORT1 with the T harness into my 2011 Mariner, and everything went smoothly, including programming. After a couple of starts, I intermittently have been getting no starts, where you can see the blue LED flashes from the Canbus seeing the remote, the red LED turns on, all the accessories turn on, but the engine doesn't start. Sometimes, but not always, I get the key ignition chime after driving, but only if the T harness connected to the EVO module

0

2010 Ford Escape Hybrid Door Pin Wire Location

I FINALLY found the 26 pin plug where the Green/Violet Driver Door Pin wire is located. It's in the driver kick panel. But it is all but impossible to get to. Really really really difficult as it is buried behind steel braces that cannot be removed. There is certainly not enough slack to get fingers in there to cut the wire and then attach the 2 separate wires needed. How do I accomplish this?

0

2011 Escape. Successful program, no Start.

Programmed using two working transmitter style keys. Program followed the sequence exactly. Yet nothing happens when lock lock lock or lock unlock lock is pressed. (Other than the doors locking and unlocking). I followed the installation guide 77081. Which says ORANGE/ WHITE wire for IMMO POWER is "not connected", as well as the PURPLE/YELLOW (KEY SENSE). Is this correct? Also, this is the Fort4 harness, not the Fort1.

0

2016 Escape No Lock after start

Hi, My evo-all (FORT4 T Harness) is installed and working with my fob. However, I would like my car to lock and arm or at least lock after it’s started. If I enable D2 the car gives me the error (no key detected) and does not crank. If I enable D5 (Lock Door After Start), the car will start then the “Door Ajar” message pops up, horn begins to alarm and the car shuts down. My configuration is exactly as the install guide suggests, the lock and unlock wires are tapped and the door switch wire is spliced into the module (properly polarized). I have not installed break lights or any other optional functionality. Any suggestions? I need rap functionality and arm disarm of factory alarm so reattaching the door pin wires to each other is not really an option. Door ajar sensor works works correctly without those options enabled and works properly any other time.

0

1 amp diode wiring evo-all fort4 2016 ford escape

installing evo-all fort4 t-harness on 2016 ford escape, the instructions list a 1-amp diode as not included and the wiring diagram shows it used on the white/black wire connecting to the door lock. There already appears to be a factory installed diode on the white/black wire at the base of the t-harness connector, is a second user installed 1-amp diode also required to be wired, or was it pre-wired with the t-harness and the manual incorrectly lists as not included?

1

Programming evo-all 2010 Ford Escape

When trying to complete programming the engine doesn't come on. The dashboard lights up, the ignition seems to initiate, but doesnt turnover, and a security light in the bottom left of the dash flashes. The module flashes red about 10x and then all lights on the module go out completely.

0

Can EVO-ALL standalone be installed into a 2007 ford escape hybrid?

Guide 32171 (THAR-FOR1 THARNESS stand alone installation) indicates that the evo-all module can be installed into a ford escape hybrid vehicle. The evo-all module I have is programmed with C1, D1, D1.6, A5 off, program lock, and H2. It is not programmed with D4 though. Guide 34441 for stand alone installation shows that the D4 option is required for hybrid vehicle, which mine is). I have a T harness also with this module. Does the evo all module have to be programmed with option D4? Also, the lock/unlock input external controls are connected via a dashed line in guide 32171. Do these dashed lines indicate that they don't have to be connected as it is an option? Thanks for your help.

0

Minimum wiring requirements for 2013 Ford Escape

I am trying to install EVO-FORT1 w/ T-Harness on 2013 Ford Escape. On wiring diagram, the yellow/black wire from t-harness has a splice point of 3 wires A1/RS6/A16. 1. Does this mean RS6 wire also needs to be spliced in conjunction with other 2 wires A1/A16? 2. Does my EVO come preprogrammed to do 3X lock start?

0

2011 ford escape evo-all lights not coming on

I have a 2011 ford escape. I wired everthing just as the directions say. I wired the lights with the 5 pin relay as the directions indicate. When checking for the violet/white wire in the kick panel my test light isnt coming on When i turned my parking lights on. Should this test out with power when i turn my lights on??

0

tach wire for ford escape hybrid 2009 with ms sync

the wiring diagam shows pin 140 (ac/data)but on the ford escape hybrid 2009 with MS sync that wire is not there. what wire is the right wire for the tach?

0

installer says that Key-override-all is defective

I had a rs-160-edp+ v-2.0 installed by a local insaller and he is telling me that the key-overide-all is causing my 2009 ford escape hybrid to resart and that it is defective and I need to replace it . The vehicle wil lsart but it stops runing after about ten seconds and then restarts.

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer