Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question

0

2012 Infiniti EX35 Heater Not Blowing Hot Air

I have Linkr LTX LT3 paired with Evo All NIST1, everything is connected correct vehicle starts with 3x lock or using App. My question is where in the flash settings do I got to enable heater to work. Because when starting the car all i get is air but heater not working until i press the brake pedal then you can feel hot air coming. Please advise thanks!

0

How to set up for telematic app

I try to install the app telematic to use with fortin

0

cannot to go through step 6

hello. did install evo-nist 1 on my 2011 infiniti qx 56 with t-harness. cannot to past step 6. when press brake pedal , yellow light still solid. reset already programmer and flush it -still nothing. with inteligent key and no battery still can start the vehicle. if i skip 6 and 7 it will follow instruction but no start. on dash have a light for imobilazer or security.

0

Does wire A16 (purple/yellow) need to be tapped into wire A10 (lt. blue/black) 2013 Infiniti G37 sedan/evo-nist1?

Does wire A16 (purple/yellow) need to be tapped into wire A10 (lt. blue/black) 2013 Infiniti G37 sedan/evo-nist1?

The wiring diagram for a 2013 Infiniti G37 sedan, using an EVO-NIST1 shows that the A16 (purple/yellow) wire needs to be tapped into A10 (lt. blue/black) wire. 

Im trying to see if this in necessary because both wires are attached to the same connecter. Furthermore, none of the install videos I have found for this set up and vehicle have mentioned connecting these wires to one another. What will happen if it is not connected?

1

Is it necessary to connect the 3 wires at the BCM if I dont plan on using an RF Kit on a 2013 Infiniti G37?

Is it necessary to connect the 3 wires at the BCM (green 40 pin connector) if I dont plan on using, or have an RF Kit, on a 2013 Infiniti G37? Just wondering if these connections are for added features or they are necessary for the basic stand alone install.

1

Is it necessary to connect the 3 wires at the BCM if I dont plan on using an RF Kit on a 2013 Infiniti G37?

Is it necessary to connect the 3 wires at the BCM (green 40 pin connector) if I dont plan on using, or have an RF Kit, on a 2013 Infiniti G37? Just wondering if these connections are for added features or they are necessary for the basic stand alone install.

1

Have the wire colors or positions changed from 2020 to now on the install sheets?

I have an Evo-All dated 10/2020 (sold as an Evo-Nist1). It was never installed and I am preparing to install it into a 2013 Infiniti G37. I would like to know if the wires or colors have changed in the installation instructions since then. If they have, is there a way to get a copy of the older instructions?

0

How to make this work on my 2.2d Infiniti Q50?

Hello, I have tried multiple times on both the standard Q50 and 2.0t models settings with diesel mode enabled but it will not work with my 2.2d model. When I go to remote start, the battery turns on, which is then followed by the dash being lit up with all sorts of malfunctions, faults, check engine light, etc and refuses to turn the engine over. However when I unplug the unit the vehicle works as normal even with all the piggy backs in so I don't think it's a case of loose wiring. Not sure if it matters but I purchased the kit through MyPushCart, who doesn't seem to be able to help me. If possible could I be told what vehicle and settings I should select in which to make it work? Would greatly appreciate that as I keep hitting the DCryptor limit trying different settings. Also do I still need to use the OBD II piggy back or is it not necessary? Thanks.

0

DCRYPTOR reset and help

Need my modules dcryptor limit rest - S/N: 001A07 602430 Also, I bought the Q50 module but mine is a 2.2d model, which seems to not work with the standard dcryptor settings for the Q50 in general. Should I be using the 2.0t's settings instead with Diesel mode enabled? Would appreciate any help on this front. Thanks

0

infiniti evo-all---evo-key

Hello. Is there a diagram (better if it is standalone) for evo-all such a connection on 2015 infinity Q50, like evo-key? By RX-TX

0

After following procedure for bypass on Evo-all correctly decryptor says empty key data?

Tried multiple times and every time after getting the rapidly flashing blue light and after the alternating red and yellow when I go to decrypt it says key data is empty?

0

2016 infiniti Q50 (4 cyl)

If we press the start-stop button once, then the remote start works without problems... If we don’t press it, then after 8-10 attempts it starts starting normally. Power is supplied to ON1, ON2, ON3 and ACC during remote start...Maybe somewhere else need to supply power?

0

2016 infiniti Q50 (4 cyl)

If we press the start-stop button once, then the remote start works without problems... If we don’t press it, then after 8-10 attempts it starts starting normally. Power is supplied to ON1, ON2, ON3 and ACC during remote start...Maybe somewhere else need to supply power?

08/05/2024

Infiniti