Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question

0

2018 Acura MDX EVO-ONE + T-Harness w/ take over

Have such problem’s: 1) Almost always (7/10 remote starts) after successful remote start have keyless access system indicator after press and release the Push-to-Start button once 2) and I think as a continuation’s of the 1st problem do not work multi-view rear camera (also 360 view) and blind spot system. When I turn on reverse gear I dot alarm on display: rear view camera do not work when engine do not start. So only stop and start engine again fix it. Please advise

0

'10 MDX EVO-ONE w/ RFK942 remote not working, no green led lock/unlock/start

I've installed the EVO-ONE & harness w/ RFK942 remote kit on my wifes 2010 Acura MDX and it has been working fine for about 3 years till now. My wifes tried to remote start and car was not on when she walked to it, and she tried to unlock using the 942 remote and it didn't unlock for her nor any other buttons did not work. Used her oem remote to unlock and locks fine but alarm goes off when opening door due to how it's programmed but eventually she got it to disarm. To troubleshoot, I've tried pressing all buttons and all lights the blue led for button press confirmation but did not light a green led for confirmation of communication to main brain like it usually do. Checked if remote buttons is disabled (trunk>lock+trunk) but remote with just blink rapidly for a second and no leds on. Check if in valet mode and it was not as the led was not constant lit on antenna. Then I've reprogrammed the remotes (2nd remote probabaly just need new battery but if i press 2 buttons a second apart the 2nd press will not confirm blue led press and remote will not light any leds when any buttons are press for about 5-10 seconds and will not program). None of the above did not fix issues. I am seeking solutions before I dig into the dash to reprogram the brain. Thoughts?

0

2011 Acura MDX Help....

I installed two of these on my vehicles in the past and everything worked flawlessly. I love this product. However, today I installed this on my coworkers 2011 MDX (Acura) regular key, evo all, with T-Harness. I made all the connections as per the instructions. The hardest part was getting steering wheel column plastic off. HAHA I pressed the button and plugged in the 6 pin connector and it just continues to flash thru the colors. It never turns red like the instructions say. I did a trouble shooting form on the website and it says the firmware is out of date. So I just bought a flash link updater. Is there anything I missed?? Are there any hints to let me know about for the updater when I get it? THANKS

0

Evo one does not enter program mode to program telematics unit.

2020 rdx push to start. Nothing happens after holding the button for 5 sec with ignition on.

0

Start works, but remote stop does not.

Remote start works on 2018 Acura TLX, but 3x lock button doesn't stop the car. I tried waiting over a minute, but can only stop the car by opening the door.

0

Does a THAR-ONE-HON4 Harness fit a 1015 Acura TDX with factory push start button?

I have a Fortin Evo One remite start device but the harness I got wa for a regular key car. Would a Thar-one-Hon4 T-harness for my 2015 Acura RDX? It's basically the same car from 2013-2018. Thanks.

0

bought evo one and do i need the all ?

not very much info 02 m/t rsx and the uplink ...i have all the alarm and oem fob door locks and hood sensor which guide shall i follow? do i need tyo return this product and get something else the guids are very confusing as well as the infor the evo one has trhe security alarm the stufff i need and the thuing has a wire loop that uim assuming if cut goes for automatic vrs mt? aloso i dont have an original key i have a cut key with a signal but they couldfnt program it because it wouldnt start ?

0

Which wire on the THAR-HON-A2 connector needs to be cut for a 2010 Acura MDX EVO-ONE Installation?

The installation guide for the EVO-ONE on a 2010 Acura MDX states that a wire has to be cut on the green male side of the THAR-HON-A2 connector, and that wires D1 and D3 are connected to the two newly created ends of the cut wire. Which wire am I to cut? Any and all help is greatly appreciated. Thank you!

0

dcryptors limit has been reached for this car

2018 acura rdx used the t harness rev 3 and evo one . I did everything step by step and it wont start after several tries I get this error

0

dcryptors limit has been reached for this car

2018 acura rdx used the t harness rev 3 and evo one . I did everything step by step and it wont start after several tries I get this error

0

Blue light not flashing when pressing lock button, no 3x start. Programs successfully.

0

Can't save options on Flash link

I am trying to install an EVO-ONE for remote start on a 2009 Acura RDX but I am having trouble with the flash-link-2. I connected the device, flashed to the recommended firmware update, then when I changed the options C1 and D2 to "ON", I receive an error message that says "the current unit does not support this feature." Could you please help me figure this out. Also, I installed the system with the THAR-ONE-HON1 T harness and there was a brown wire with an inline fuse that was not mentioned in the 57691 guide. It is on pin E1. Is this wire needed for this application?

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer