Questions & Réponses

2014 Mazda CX5 ; manual push to start ; Evo-one w/MAZ THAR ; SN 002b04 638289

Cranks but doesn't start. All fob functions work, car runs normally, and it goes into ready mode and shuts down after exiting. Won't autostart after getting out of the vehicle - what am I missing? Valet mode off.

Using default settings with the plug&play harness.

Firmware 85.14

A1 through A-10 : ON

A11 OFF ; B1 OFF ; C1 ON

D2 ON

D3-D5 : OFF ; D6 ON

Firmware 1.26

2 through 15 : option 1 (default)

16.5 ; 18.1 ; 19.1 ; 20.8 ; 21.2 ; 24.1 ; 25 (off) ; 26.1 ; 29.1 ; 30.1 ; 31.1 ; 32.1 ; 33.2 ; 34.1 ; 35.1 36.3 ; 37.1 ; 38.1 ; 39.1

2015 Mazda 3 Grand Touring Hatchback, push-to-start, smart key, manual transmission.  I cannot get the module to start the vehicle with 3x OEM remote lock.  I've followed the instructions for manual transmission in Guide #68261.  My EVO-ONE serial number is 002B04 298695 and it is dated 09/2022.  Here's what I've done:

EVO-ONE flashed with Firmware 85.12. Using T-Harness. Yellow loop wire NOT cut White wire labeled "for manual transmission only" on the T-harness is connected to the white wire coming out of the 20-pin connector.  These wires are just butt spliced with no other connection. DCryptor process to enable key bypass appears to have been successful from all FlashLink software messages. Remote starter option 33 is set to mode 2 for foot brake - handbrake - release foot brake Ready Mode process. Remote starter option 38 is set to mode 2 to enable 3x lock with OEM remote. Bypass option C1 is on for OEM remote status monitoring. I did not install a hood pin.  I am not concerned about remote starting while the hood is open.  Bypass option A11 is set to "off." Bypass options for foot brake, hand brake, door output monitoring are all set to "on."

To enable ready mode, I depress the foot brake, engage the hand brake, release the footbrake, and exit the car while it is still running without pushing the start button.  The car just sits there and runs, nothing happens when I close the door and walk so that the smart key is out of range.  I also tried doing this with shutting the car off before exiting and was still not able to remote start the vehicle.

When I press the lock button on the OEM remote, the blue LED on the EVO-ONE blinks indicating it is reading the CAN bus messages.

When the car is running, the yellow LED on the EVO-ONE is steadily illuminated.

At no point does the red LED on the EVO-ONE illuminate.  It does not turn on after pressing the OEM remote lock button 3x.

When I press the OEM lock button 3x after the above ready mode process, absolutely nothing happens except the car horn beeps on the 2nd and 3rd presses like it normally would.

Thanks in advance for your help.

2016 Mazda 3 Fortin EVO-MAZT1 Stand-Alone add-on

So when I go to start the programming the first time I turn the car on like the video (https://www.youtube.com/watch?v=5ETmJn9RIlE&feature=youtu.be) the security indicator flashes quickly for about 30 seconds.  if I turn it on a 2nd time like in the video the security indicator light is only on for a few seconds like it's supposed to.

If I wait to turn off the car until after the security indicator stops flashing then the yellow light does not turn off.

if I only wait the 3-5 seconds and turn off the car the yellow light will turn off and the security indicator will flash quickly for the 2nd key also. and the yellow light will turn off but the red and yellow lights don't start flashing and it doesn't turn on and off the car.

I have tried removing the batteries from the key fobs and trying that but I might have messed that up and will try that again.

is the hood pin and wiring required for programming? because I haven't hooked that up yet.

EVO ALL with THAR-MAZ1  T-harness, All the connections were made however was stuck at STEP 5, The blue LED was on solid then I tapped my key onto the start/stop button nothing happened. started from STEP 1 a few times but still didn't work. Tried different key position and took battery out still nothing. Newest Firmware version.