Questions & Answers

2014 Mazda CX5 ; manual push to start ; Evo-one w/MAZ THAR ; SN 002b04 638289

Cranks but doesn't start. All fob functions work, car runs normally, and it goes into ready mode and shuts down after exiting. Won't autostart after getting out of the vehicle - what am I missing? Valet mode off.

Using default settings with the plug&play harness.

Firmware 85.14

A1 through A-10 : ON

A11 OFF ; B1 OFF ; C1 ON

D2 ON

D3-D5 : OFF ; D6 ON

Firmware 1.26

2 through 15 : option 1 (default)

16.5 ; 18.1 ; 19.1 ; 20.8 ; 21.2 ; 24.1 ; 25 (off) ; 26.1 ; 29.1 ; 30.1 ; 31.1 ; 32.1 ; 33.2 ; 34.1 ; 35.1 36.3 ; 37.1 ; 38.1 ; 39.1

2015 Mazda 3 Grand Touring Hatchback, push-to-start, smart key, manual transmission.  I cannot get the module to start the vehicle with 3x OEM remote lock.  I've followed the instructions for manual transmission in Guide #68261.  My EVO-ONE serial number is 002B04 298695 and it is dated 09/2022.  Here's what I've done:

EVO-ONE flashed with Firmware 85.12. Using T-Harness. Yellow loop wire NOT cut White wire labeled "for manual transmission only" on the T-harness is connected to the white wire coming out of the 20-pin connector.  These wires are just butt spliced with no other connection. DCryptor process to enable key bypass appears to have been successful from all FlashLink software messages. Remote starter option 33 is set to mode 2 for foot brake - handbrake - release foot brake Ready Mode process. Remote starter option 38 is set to mode 2 to enable 3x lock with OEM remote. Bypass option C1 is on for OEM remote status monitoring. I did not install a hood pin.  I am not concerned about remote starting while the hood is open.  Bypass option A11 is set to "off." Bypass options for foot brake, hand brake, door output monitoring are all set to "on."

To enable ready mode, I depress the foot brake, engage the hand brake, release the footbrake, and exit the car while it is still running without pushing the start button.  The car just sits there and runs, nothing happens when I close the door and walk so that the smart key is out of range.  I also tried doing this with shutting the car off before exiting and was still not able to remote start the vehicle.

When I press the lock button on the OEM remote, the blue LED on the EVO-ONE blinks indicating it is reading the CAN bus messages.

When the car is running, the yellow LED on the EVO-ONE is steadily illuminated.

At no point does the red LED on the EVO-ONE illuminate.  It does not turn on after pressing the OEM remote lock button 3x.

When I press the OEM lock button 3x after the above ready mode process, absolutely nothing happens except the car horn beeps on the 2nd and 3rd presses like it normally would.

Thanks in advance for your help.

Vehicle type:

2011 Mazda 3 (5 door/hatchback), manual transmission, key to start. Integrated key/keyfob (lock,unlock,panic), keyless entry w/RFID chip for factory immobilizer system.

Wants:

Remote Starter, Factory Immobilizer bypass, OEM keyfob (lock-lock-lock to start), alarm functionality optional at a later date.

Ready to install Evo-One, Flash-Link and RFK442.

Few problems so far (have not started install yet or any flashing of Evo-One vehicle specific Bypass settings):

   I see a conflict between Fortin wiring guide #80431 and #29661. Same vehicle, Mazda 3 - Axela 2010-2013, but two different wiring schemes.  Which one is the more correct one, or, can you suggest a better one?

   On Fortins website, for this vehicle it states 'Automatic Transmission Vehicles Only'  In Guide #80431, pg 5, it gives Manual Transmission programming instructions as does with Guide #29661 pg6, both of which conflicts with Fortins webpage.. 

   With Flash-Link v4.51, when entering vehicle info, there is NO option for Manual Transmission.

   In Guide #94011, pg11 (Function #20) Engine Supervision: Tachless, Analog or Data-Link.

I see there is no option for a true Analog input; i.e Vacuum switch, or hardwire to coil (or even a much older method of wraping 6in of stripped wire around a spark plug wire). Is there not a true analog tach input?

   I also cannot seem to anything at all about 'clutch bypass'

So, Manual Transmission? Yes or No? 

   For the Flash-Link Manager software, the v4.51 does not reflect the instructions I found for possibly older software instructions of Flash-Link Manager User Guide v1 #68731, any updated Guide #?

Flash-Link Manager software v4.51 (when I click on Settings in the software it shows v4.51-1.1.15)

Flash-Link V4 module, Hardware V5, Firmware v4.08

Evo-One module date 07/2021, s/n (PM me for serial number), Firmware: for a moment it showed v1.25 then within a few seconds dropped down to v1.01

Thanks, Nick.