Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question

0

After install, will I still be able to use my OBD11 port like normal?

At the end of this month I'll be getting my Evo-All installed and I cannot wait! But quick question, since the T-Harness connects to the back of my OBD11 Port, after install can I still use the port to tune my Mustang? I have been data-logging with a company to get my custom tune just right, and I want to make sure I'll still be able to use the port to upload the file to my car? Thanks so much in advance!!

0

key port works but only when t harness is unplugged

2012 a4 w/push to start will not start. fortin inicated the key port has to be functional in order for it to start. but the key port does not work unless the t harness is unplugged. I was unable to get any help from fortin when i called anyone else had this issue and how can i resolve. the install thus far has been easy , simply tapped the brake signal wire and can high and can low. when the evo is connected it does attempt to start the car meaning it flashes each of the three lights but never hear the starter engadge. updated firmware as requested previously by fortin. but when i called today fortin tech was no so eager to assist. said either the evo relays are bad or the t harness is bad. can i help with anything else. I indicated i would like assistance tryin to resolve. so im trying to work through the troubleshooting he offered but now will not answer the phone. any help would be greatly appreciated.

0

Can not proceed Page 6/10 (dcryptor programming procedure). when i apply the step 4 in page 6/10 the Blue LED turns off

I've updated module Evo-One for my Audi A5 2011 Gas with key-port before the installation and now can not proceed Page 6/10 (dcryptor programming procedure). when i apply the step 4 in page 6/10 the Blue LED turns off which makes unable to continue the step 5.

0

After install, will I still be able to use my OBD11 port like normal?

At the end of this month I'll be getting my Evo-All installed and I cannot wait! But quick question, since the T-Harness connects to the back of my OBD11 Port, after install can I still use the port to tune my Mustang? I have been data-logging with a company to get my custom tune just right, and I want to make sure I'll still be able to use the port to upload the file to my car? Thanks so much in advance!!

0

After install, will I still be able to use my OBD11 port like normal?

At the end of this month I'll be getting my Evo-All installed and I cannot wait! But quick question, since the T-Harness connects to the back of my OBD11 Port, after install can I still use the port to tune my Mustang? I have been data-logging with a company to get my custom tune just right, and I want to make sure I'll still be able to use the port to upload the file to my car? Thanks so much in advance!!

1

3 pin shock sensor connector

What is the name of the type of connector used for the shock sensor port and where can I purchase a connector with a wiring harness? If I wanted to add a tilt sensor and wired the trigger into the pink/black wire (A15) would it give me a proper tilt alarm response if triggered on a two way remote or parking light flash upon disarm? I know I need to tie the trigger for the tilt alarm into zone 8 for that I just dont know where to do that. Are the ground and 12v leads coming from the shock sensor port only active when the alarm is armed or are the always active?

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue