Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

18/01/2023

 Ford Todd Lusby (130Pts.)

0

2010 ford escape KEY-OVERRIDE-ALL

I'm installling the KEY-OVERRIDE-ALL with a DEI remote start. When I attempted to program prior, I would see the LED start flashing, but programming didn't complete. Now when I attempt to program, the LED on the module stays on and the security light on the dash flashes rapidly. I've confirmed I have 12V on Red, Ground on Black, Ignition on Yellow, and remote start staus on Blue. Is there anything else i should try on this module? The module was purchased new in December and hasn't been installed in another vehicle.
Login to reply View 1 answer(s)

26/12/2022

 Ford Ryan Andersen (130Pts.)

0

2017 Ford Focus Programming Issues

I am having some difficulty programming my EVO-All FORT4 with my 2017 Ford Focus. The T-Harness is all hooked up, and the device has been flashed with the correct module. When I attempt to pregrade both keys, nothing happens when I press the program key at the end of the sequence. When I attempt to program a single key, it doesn't change from red to yellow. Any and all help would greatly appreciated.
Login to reply View 1 answer(s)

25/08/2022

 Ford Joe Allison (220Pts.)

0

2017 EvoOne with TharFor3 T harness, blue light won't blink on programming

Thank you in advance for any help! I am a long time using of the EVO ALL and have done a few EVO ONE. A bit stumped on my 2017 F150 though. Using EVO ONE with the THAR FOR 3 harness. All plugged in. Following wiring diagram for the A1 and A16 (put them together) on the white 20 pin connector. When I go to program it, I can't get it to "blink blue". Therefore, I can't get any further in the programming procedure. Followed the directions in the Guide. What could I be missing? Joe
Login to reply View 1 answer(s)

18/08/2022

 Ford jaber awadh (340Pts.)

0

F150 2012 programming

I have a f150 2012 i done every thing 100% In the programing phase I made every thing i enter the first key after the second key and after the first key then the blue and red started flashing after that only the blue led appeared and the still on without the key but if i unplugged the red connector the car turn off please can you help me in the programing
Login to reply View 2 answer(s)

18/08/2022

 Ford jaber awadh (340Pts.)

0

F150 2012 programming

I have a f150 2012 i done every thing 100% In the programing phase I made every thing i enter the first key after the second key and after the first key then the blue and red started flashing after that only the blue led appeared and the still on without the key but if i unplugged the red connector the car turn off please can you help me in the programing
Login to reply View 2 answer(s)

18/08/2022

 Ford jaber awadh (340Pts.)

0

F150 2012 programming

I have a f150 2012 i done every thing 100% In the programing phase I made every thing i enter the first key after the second key and after the first key then the blue and red started flashing after that only the blue led appeared and the still on without the key but if i unplugged the red connector the car turn off please can you help me in the programing
Login to reply View 2 answer(s)

27/12/2021

 Ford ryk (220Pts.)

0

2011 Ford Escape red light stays on during programming - SOLVED

Vehicle: 2011 Ford Escape

Evo All #001A07260304 installed with T-harness THAR-FORD4; plug-n-play install, teed connections to ignition switch, immobilizer antenna and OBDII connector; no wires spliced

Can't get the unit to program.  Process: Hold program button, plug in data cable and release on red light.  Insert key and turn on until theft light turns out.  Remove first key and insert second.  Turn on for 3 seconds, theft light goes out, turn off and remove.  Last step says to press and release programming button within 5 seconds (this is where it gets stuck).  Red light should flash 10 times and blue light should flash 10 times and ignition comes on and turns off again.  When I press the button the last time, the red light blinks and just stays on.

I've tried the firmware downgrade listed in https://fortin.ca/en/qa/92073/faq-red-led-stuck-on .  That link says to downgrade to v 0.99 but the lowest version for Ford appears to be 4.01.  I flashed 4.01, power cycled in vehicle, reflashed v 71.52, unlocked settings and reset the unit.  Still same results.

I've also tried testing the data bus.  Hold button, insert data link connector, release button on blue light.  Connected all other connections and turned key on.  Blue light stays solid.  Shouldn't it flash on data?

The yellow wire is not connected as it seems to be part of the T harness, but I've tested it for 12v on ignition and it is getting it.  I don't have the valet switch or hood pin switch connected.  What am I missing?  I'm wearing out the plugs with all these connections/disconnections.

 

 

 

Login to reply View 1 answer(s)

18/12/2021

 Ford Corey Wilson (130Pts.)

0

Red light stays on during programming and wont program the keys

I hVE 2008 Ford Escape. I installed the Evo all fort4 with the the t-harness. I have installed all connectors(1,2,3) and connected a relay to the lights as instructed in step 4. I plugged the black connector in while holding the button in and then let it go when the red light came on. I put in each key for 3 seconds each and then pushed the button in. It didn't start the vehicle. Red light stayed on teh whole time. It only blinked when I pushed the button in. What causes this and how can I fix it?
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue