Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

14/11/2024

 Audi optyk07 (150Pts.)

0

2014 Audi Q5 Evo All not flashing yellow in step 8 of Key bypass programming

Im not able to proceed from step 7 in guide 77151. When it should begin to flash yellow and red alternating it just flashes red.
Login to reply View 1 answer(s)

27/10/2024

 Volkswagen Jung8724 (160Pts.)

0

EVO ALL Stuck in Yellow and Red Light Flashing

Hello, I am installing this on my 2012 VW Tiguan. I followed the process guide 92511. After decryptor and returning the vehicle, yellow and red LEDs flash, instead of staying on like explained on Step 13. Now it says my unit (SN 001A07 559614) has recheaed its limit and I am really stuck. Can you please assist? Thanks, Andrew
Login to reply View 0 answer(s)

09/12/2022

 Lexus Niko Soikkanen (130Pts.)

0

lexus gs450h L10 fsport 2012 PUSH TO START EVO-ALL does flash red and yellow.

Can someone help, when I connect EVO-ALL to car and follow instruction, it starts flashing red and yellow. According to instruction I have to dcrypt module, but when I try to do it, program says invalid key data. master restart didn't help. SN #001A07 391294
Login to reply View 1 answer(s)

10/01/2021

 Mazda Ahmed Alhammad (140Pts.)

1

red flashing instead of red and yellow flashing?

Mazda cx-5 2018   Evo all guide # 66311   on step 13 I have an only red light flashing once every second and did not stop!!   I tried and read different solution founded here, but it ends with the same red flashing   all wires connected correctly 
Login to reply View 1 answer(s)

03/01/2021

 Mazda Zack Rogers (190Pts.)

1

2018 Mazda 3 Automatic - Ignition comes ON but does not flash Yellow and Red (Step 13)

Hi Fortin Q/A forum. Installing a EVO-MAZT1 which I first connected to Fortin FlashLink Manager to upload the latest firmware (suggested 85.10) on Hardware 7.0. Loaded Suggested Options, then went to the car to perform Programming. Programming Steps 1-12 go as planned, but when the ignition turns ON and OFF by the module, the Yellow and Red LEDs do not flash as indicated in the guide. I disconnected the module as indicated by the instruction manual (disconnect all connectors, saving the 4-Pin Data connector for last) and then connected it back up to FlashLink Manager to run DCryptor. DCryptor says INVALID KEY DATA and "The immobilizer data received by the bypass module is incomplete. Please try again. If this error persists reconnect the module to the vehicle and start programming procedure from STEP 1." Via the troubleshooting guides, I removed the batteries from the key fobs and tried again. Verified connection to the data key wire was correct (Car's Red wire to bypass' Light Blue and Black wire) and secure (shaved insulation, wire inserted through conductors, wire wrapped, soldered, and taped). Door lock actions can be seen on the bypass/remote start module as indicated by the Blue LED. I'm confident those wires are connected correctly and securly as well. I tried all of the above with and without the front fuse box ground to Pin 11. Someone please explain what that does, but the manual did not indicate if it was mandatory or optional so I tried both ways. In the end, I can't get DCryptor to program the module with the learning received during programming. I fear it has to do with the Yellow and Red LEDs not flashing. Help would be appreciated. Thanks!
Login to reply View 1 answer(s)

15/07/2020

 FAQ Robert T (300340Pts.)

0

FAQ: GM Flashing RED and YELLOW

If the RED and YELLOW flash during programming after cyling the key to the ON position, do this.

 

    Turn car off Plug in ONLY the RED connector in the EVO Start car and let run 5 secs. Shut down car. Do NOT disconnect RED connector Wait 20-30 Seconds Start programming
Login to reply View 0 answer(s)

28/07/2020

 Ford Jesse Ruiz (190Pts.)

1

2020 F150 auto start not working, lights just blink alternating yellow and red.

I have a 2020 Ford F150 std-key-with-keyless and cant get the auto start to work. I set the evo-all to blue for programming, then I plug in the bottom cable. Turn key to on, yelow red leds turn on then start to blink and alternate. After 20 seconds I turn key to off and disconnect it. i then take it to my laptop and program and flash it. Once thats done I connect it per the instructions but the problem is I never get the red yellow lights to go solid. They just keep alternating and blinking. Turning the key on nothing change or off all I get is red and yellow blinking lights. Heres a video I did of my issue. I set the start time to the issue mark but you can scan it all if needed. https://youtu.be/eNiUY9VVx-c?t=363 Thanks
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue