Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping



Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question


Reset a couple units I never got working

Hello, I'm wondering if it's possible to fully reset a couple evo-one units I bought but never finished installs for cars I no longer have. Would like to install in my current vehicle if possible. Unit#1 07/2017 service no. 002B07 183915 Unit#2 04/2017 service no. 002B07 172354 Thank you


Acura Son Vo (130Pts.)


please reset flash limit on my evo-one


I am unable to factory reset my evo all

I am unable to factory reset (via instruction). Always stays solid red. Any ideas? Its a BRAND NEW UNIT and updated/reflashed/etc with no master reset lock. NO IDEA!


FAQ: How do I reset my EVO-ALL?

The master reset is very simple on the EVO-ALL, but be warned that a reset will also reset all the options back to default if Settings Protection was not enabled. So if you have any special options enabled (such as the all famous D1 and C1 for 3x lock start), or if the vehicle programming requires the use of the DCryptor, make sure that you have access to the Flash-Link Manager!

So here it is...

    Hold down programming button while plugging in datalink connector. Let go of button when LED is RED. Push and hold button again until all three LEDs start to alternate. Disconnect unit, it is now reset.


Flashlink evo one programming

Can't program bypass settings from flashlink only remote starter can adjust or change and save keep give error no connection when i switch to remote mode working , new flashlink download and updated firmware of flashlink for computer usb cable, evo one is brand new never installed before, it is show 1/8 time remains in programming, should i do master reset and how i can do i don't have valet button.


how to reset evo-all

I've followed the reset directions, however the red light just stays on. No other lights blink. I plug the 4 wire black datalink connector while holding the button. The red light turns on, and i release the button. I press the button again and hold it but nothing happens. Questions: how long is it supposed to take until other lights come on? What is the other end of the Datalink cable supposed to be plugged into?


Can a master reset convert satnd alone to remote system?

I have a customer with an EVOGM1 standalone in a 2015 Impala. Because of the keyless entry not working while the vehicle is running, he'd like to add a Crimestopper LC1 remote/receiver. The customer does not have a flash loader, but I'm thinking that if he does a master reset, he will clear out C1/D1, the EVO will default to working via datalink and the system will work fine with the LC1. Is this correct?



Hi. Does anyone know how to reset the EVO-KEY? Thanks


relay in evo-all clicks as soon as 4 pin data harness is plugged up? ignition stays on...

Hello am working on a 2012 ford fusion evo all with t harness. Stand alone mode. as soon as i plug up the red relay harness the ignition comes on and it tries to start?? i have checked all connections twice and i am sure it is correct. I can only plug up the 4 pin data plug for power and the internal relay clicks and engages. that does not seem normal to me as the relay is always on?? the ignition is always on and will not power down, all wires are correct. defective unit? service number 001a06434440


programming is not working for me?

im not sure if this is a problem or something is not done right, got all the needed wiring done, but not the hood, connected all the needed remote connectors, and at the time of programming the bypass blue comes on but turns off at ignition ON and blue led comes back on when ignition is OFF. The website support ays that it is crossed wires on the hi-low can, but all are the way it supposed to be(gray/black-orange/brown & gray-orange/green). i checked the wiring couple of times but not doing any change.


How do i reset the EVO-ALL?

I want to reprogram the module, how can I do it? I've a Sentra 2006 and when I tried the remote starter, the motor only cranked. If I let the key in the switch without turning the key, the remote is working. So I thought that it was my EVO that was the problem and I tried a method suggested in the FAQ to reset the module and I can't reenter my program. Also, is it normal that the three leds blinks after the program is set? Laurent Demers

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue