Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question

29/12/2021

Ram joe tom (410Pts.)

0

Can bus faults after 3 trouble free years

Is there any warranty on a the evo device that stopped working out of the blue? My 2014 ram broke down a couple of nights ago and the dtcs state the can bus was not ok. U0001 I removed the can high wire from evo and all issues went away and cleared. I love my remote starter and fob, is there anyway to get this module repaired or replaced ?

29/12/2021

Ram joe tom (410Pts.)

0

Can bus faults after 3 trouble free years

Is there any warranty on a the evo device that stopped working out of the blue? My 2014 ram broke down a couple of nights ago and the dtcs state the can bus was not ok. U0001 I removed the can high wire from evo and all issues went away and cleared. I love my remote starter and fob, is there anyway to get this module repaired or replaced ?

0

CAN BUS PROBLEM

hello having a problem with the device as the when EVO ALL is connected , the car doesn't go to sleep mode and remains draining battery with current drainage of (0.2 amps) , normally without the device it's (0.02 amps) when it's disconnected, it goes to sleep mode and current drain stops i tried all possible settings ON and OFF, nothing changed i tried to disconnect cable by cable each time untill i identified Cable (C) which is containing the brown wire C5 only when i dosconnect this cable , Car goes to sleep mode and current drainage stops the problem i cannot keep it disconnected as the module is not functioning properly without C5 being connected to it's place can you give me any tip or solution for this   Car is Buick Regal Service number is 001A06839987 Radio is having android interface attached with the car main screen that is normally shutting down with car CAN BUS, but when EVO is attached it never shut down and this is the main source of power drainage

0

CAN BUS PROBLEM

hello having a problem with the device as the when EVO ALL is connected , the car doesn't go to sleep mode and remains draining battery with current drainage of (0.2 amps) , normally without the device it's (0.02 amps) when it's disconnected, it goes to sleep mode and current drain stops i tried all possible settings ON and OFF, nothing changed i tried to disconnect cable by cable each time untill i identified Cable (C) which is containing the brown wire C5 only when i dosconnect this cable , Car goes to sleep mode and current drainage stops the problem i cannot keep it disconnected as the module is not functioning properly without C5 being connected to it's place can you give me any tip or solution for this   Car is Buick Regal Service number is 001A06839987 Radio is having android interface attached with the car main screen that is normally shutting down with car CAN BUS, but when EVO is attached it never shut down and this is the main source of power drainage

0

2016 kia soul singal or double pulse for locks

Do i need a single or double pulse for the locks to work correctly .I had it set on single pulse .25 sec but locks dont seem to unlock all the time . except driver side. Already reprogramed the unit again followed programming for no ems wire or becuse this is hooked up to the can bus should i use the other programing methed .

0

Can bus not progrmming ford edge 2014

I had an issue sunday with this, and i received a reply about hooking up the three wires from the t-harness. that got me alot further! Tonight I hooked up the additional 3 wires from the t-harness and was able to program the unit with the keys. the blue red led flashed 10 times, then the blue led comes on by itself for a second or so then goes off. no more activity. I retried this maybe 5 times. I assumed I had an issue with the Can Bus wires, so I disconnected them verified the colors and remade new connections. same result. Also once it programs (doors lock and unlock and lights flash) when I turn the key off and remove it, the radio and dash lights stay on even after closing door and waiting a while. I assume this is a symtom.

25/09/2016

Kia SC (160Pts.)

0

Evo-One not programming door locks on 2013 Kia Soul (key start - uses a key)

I've installed an EVO-One in a 2013 Kia Soul (has a normal Key to start vehicle). The install was very simple, I did not that there is an error in the guide regarding the can bus. In this car, pin 6 (can high) is a blue wire, pin 14 (can low) is a red wire. Initially I had only followed the color code and the unit would not learn the can bus at all. I reversed the wires when I noticed the wires where reversed and the unit was able to learn the red (brake signal). It is not able to learn the door unlock / lock from the can bus, and during the programming sequence, I never had the flashing blue sequence to learn the door locks. I'm unsing a Fortin RF KIT 2W (RF642W). I'm able to remote start the car, but once started, the OEM remote is unable to unlock the doors ( I need to use the key in the door cylindre). The fortin RF kit is also unable to unlock / Lock the doors. I also can not stop the vehicle remotely, only by letting the time expire or pressing the break. Appreciate any help.

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue