Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Utilisateur

Joe Sharkey

À rejoins en date due:

Dec. 16, 2015

Points

290

Commentaire(s)

2

Questions votée(s)

0

Réponses votée(s)

2

Votes positifs

0

Votes contre

2

Votes reçus

1

Votes négatifs reçus

0

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez une question

0

2012 A4 PTS Central Locking

Remote starter works perfectly, but one complaint I have, and maybe is a setting on the unit... I have central locking enabled, so only have to unlock the doors once and all unlock, instead of having to hit unlock twice. When I remote start the car, it locks, starts....I unlock the doors with the Fortin remote, all doors unlock due to central locking...I put my laptop bag, or backpack in the back seat, get in, drive, the doors automatically lock when the car is put in Reverse, or Drive, as usual. When I turn off the car, normally all doors unlock, but if I remote started the car, only the front doors unlock, I have to press unlock on the remote to get my bag out of the back seat. If I didn't remote start the car, all doors unlock when I shut off the car. I have not tried to turn off central locking and see if it works just like it would be without remote starting.

0

2012 Audi A4 PTS won't start

Everything connected correctly,I assume. The only thing I couldn't tell from the diagram and the pictures is the black ignition wire behind the fuse panel. The picture from wire diagrams had the pin pointing at nothing and was no description of which harness the wire is coming from. I looked through all the harnesses and found one giant black wire, which I assume is the ignition, so I connected to it. audi requires the key port and emergency key to be wrapped, so I wrapped 3 times around the key port and 10 times around the emergency key and have them in close proximity behind the dash all other functions of the evo one work with the fort in RF kit, except ignition during remote start. It is an automatic, so I cut the jumper loop. The unit programmed correctly, and the remotes programmed correctly as well. edit. I verified that the ignition cable behind the fuse panel is correct. I also tried remote start with a fob in the ignition and it worked, so it's gotta be the emergency key and key port wiring deal. I have the key port wrapped 4 times and the key wrapped 10 times. I've redone this 3 to 4 times and still can't get it to work. I verified the emergency key works in the dummy fob,and it works. I can't actually get the key port out of the car, so I'm wrapping it while it's in its harness, but pushing the wire as far as I can to the front of the key port. I'm using a solid copper 22 gauge wire.

1

2013 Elantra PTS - EVO-ONE Won't Start

I installed a new EVO-ONE in my 2013 Hyundai Elantra sedan PTS. I soldered the wires instead of using quick splice wire connections. I double, triple, and even 10x checked all the wiring. I even called Fortin support because some of the wires on the standard install weren't the same color coming from the car, they said it's the wire position that's most important. I also purchased the Fortin RF remote kit. I bought the unit from eBay, the seller programmed the unit for the RF kit and the car. I checked the parking light wire to make sure it wasn't +12v, once that was hooked up and knew that all basic install wires were connected, tried the remote start, and it did not start the car. The parking lights flashed 3 times, but did not start. Lock/Unlock/Trunk Release all work, but starter does not. I tried to check the various ignition wires with a multimeter at the harness plug, but I don't know if any are supposed to send +12v from the Fortin unit or not. I previously programmed the remotes and got the responses from the car that the instructions indicated I should get. I turned on the car ignition, got orange light on EVO-ONE. Locked the doors, the antenna started flashing blue, the EVO-ONE was flashing red. When trying to remote start, the EVO-ONE flashed red I believe, until the "did not start" signal came back to the remote. Any help I can get?

No results

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez une question

Support Technique

Recherchez parmi nos produits les plus populaires et les sujets d'installation disponibles dans notre section Questions et réponses.

En savoir plus
Téléchargez notre application de guides de dépannage étape par étape disponible pour iOS et Android ou parcourez notre version de bureau.

En savoir plus
Accédez à la plus grande base de données de schémas de câblage et de photos en ligne de l'industrie. Un jeton gratuit est fourni dans chaque boîte EVO-SERIES.

En savoir plus
Vous n'avez pas trouvé l'information que vous cherchiez ? Posez-nous une question en remplissant le formulaire de demande de support technique. Un spécialiste produit vous répondra sous peu.

En savoir plus
Des solutions de contrôle à distance et de connectivité à la fine pointe de la technologie au soutien technique haut de gamme, découvrez pourquoi vous devriez choisir les produits Fortin.

En savoir plus

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer