Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Utilisateur

Dennis Lloyd

À rejoins en date due:

Jul. 10, 2025

Points

240

Commentaire(s)

2

Questions votée(s)

0

Réponses votée(s)

0

Votes positifs

0

Votes contre

0

Votes reçus

0

Votes négatifs reçus

0

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez une question

0

Programming doesn't complete, new EVO-ALL on F150/2012, firmware flashed

Can't find anything in the questions/answers that is exactly like this issue but I can't seem to complete the programming on my truck.. I've double and tripple checked the wiring, can-high/low, key sense A1,A10,A20 were connected as well. First time it seemed to sense the keys, waited the 3 seconds each and returned to the 1st factory key.. waited for 3 or 4 minutes and no status change so I tried it again. Seemed to go a little further and the system locked/unlocked the doors and the stopped again.. no 10x flash of the indicator either. reflashed the unit and tried again, this time nothing seems to progress. I can put the unit into programming mode (blue/red solid) When I touch a key to the ignition I see a quick flash of the yellow, turn to run and wait 3, 2nd key doesn't show anything.. return to the first key and nothing happens. lights won't change at all and just stuck at solid blue/red. I've tried tapping the button when the key is inserted, but that does nothing either. One really strange issue is I started the truck after (unit was still connected) and it would not shut off until I pulled the connectors off the controller.. brake pedal didn't do anything, opening the door didn't light the interior or turn on the parking lights. Any ideas? THAR-FORD1 with EVO-ALL

0

New EVO-ALL won't pass step one for programming

Brand new unit EVO-ALL won't pass step 1 for programming. All three lights flash in sync (not alternating) Do these units ship without any firmware?

0

20 conductor harness wires too short??

I don't understand how people are installing these units, I can't find any way for the wiring to reach the passenger side kick panel. The wires are at least 1 foot too short on the 20 pin connector so is there a trick to the install or do I need to buy an extension? I was hoping to not splice in sections of wire but I will if I have too. purchased the EVO-FORT1 standalone with THAR-FOR1 Wires that are too short are A17-19 on the 20 pin connector "A" thanks

No results

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez une question

Support Technique

Recherchez parmi nos produits les plus populaires et les sujets d'installation disponibles dans notre section Questions et réponses.

En savoir plus
Téléchargez notre application de guides de dépannage étape par étape disponible pour iOS et Android ou parcourez notre version de bureau.

En savoir plus
Accédez à la plus grande base de données de schémas de câblage et de photos en ligne de l'industrie. Un jeton gratuit est fourni dans chaque boîte EVO-SERIES.

En savoir plus
Vous n'avez pas trouvé l'information que vous cherchiez ? Posez-nous une question en remplissant le formulaire de demande de support technique. Un spécialiste produit vous répondra sous peu.

En savoir plus
Des solutions de contrôle à distance et de connectivité à la fine pointe de la technologie au soutien technique haut de gamme, découvrez pourquoi vous devriez choisir les produits Fortin.

En savoir plus

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer