English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

17/01/2025

 Toyota JASON FORTIN (130Pts.)

0

My evo duo remote stop working

I have a toyota corolla hatch 2020 manual transmission with fortin evo duo universal remote the remote stop working recently When i push lock unlock or start the led blink rapidly but the car do nothing I double chek if the systeme was in valet mode but it seem not in valet mod... It is possible to use the factory remote with a manual transmission for remote starting ?
Connectez-vous pour répondre Voir 1 réponse(s)

12/01/2025

 Toyota mc141 (250Pts.)

0

tundra install issue now factory remote start dead

so i have a 23 tundra non hybrid that i couldnt get evo one to work and now factory remote isn't working.first off didnt want to pay 15/m for toyotas sub par remote start but i guess im going to have to now. i triple checked the wiring /splices prior to install so wiring was good. followed the procedures and all the lights during setup worked the dycriptor worked, but when i went to remote start nothing except my key fob temporarily stopped responding to doors and push button. so i went back and changed the setting to unlock door prior to start and nothing but key fob not responding no push button start. not knowing what caused it i removed it reconnected the pink wire and after a few min i could start the car and open/close doors. went in the toyota app subscribed to the remote connect and all is well except remote start is no longer working gives me a d5 error and to contact dealer. every thing else in car works just not remote start. so i connected my scan tool and now i get an u111787 lost communication with accessory gateway for bcm and special key did i fry the control module or did i break the pink wire in connector. like i said every other function works just fine only remote start ive installed the evo one multiple times in older cars with out a problem. im hoping when i take it to dealer its an easy fix like a relearn or something but i fear it will be an expensive fix
Connectez-vous pour répondre Voir 1 réponse(s)

08/01/2025

 Toyota sheehyma (130Pts.)

0

Dcryptor does not complete - No connection avalaible msg after 1hr+ decription

Hi,

I have followed the guide religiously several times now and have even performed a "Master Reset Procedure" a couple of times along the way.

Everything seems to work according to the guide:

    Programming: I obtained the red and yellow flashing lights before heading to the computer to run the "Decryptor." Decryptor: I received the Flashlink updater status: "Connected," as well as the same for EVO-ONE.

I tried two different computers (one with a very fast internet connection).

After a very long time (1+ hour), an image appeared saying "No connection available" and the following message:

The application is currently unable to load files from the server. Please try again later. If the problem persists, please contact customer support.

And here I am…

Flashlink service number: 002505 118533
EVO-ONE: 002B04 663520 (number printed on the machine*)
01/2024

*However, when I click on the "Bug Report" (top-right), I obtain a pre-filled form that shows two serial numbers:

    EVO-ONE Bypass model: 002B04 663520 EVO-ONE Remote Starter model: 002B07 663520

Please help!

Oh... While at it, I should be getting close to my EVO and other limits... if you could reset them please.

Connectez-vous pour répondre Voir 1 réponse(s)

13/12/2024

 Toyota Todd Raycraft (130Pts.)

0

Sold vehicle with Remote start installed.

How do I transfer ownership of the remote start if I don't have the security key? Recently sold my truck and it had the Evo one remote start system installed but I have lost the security key. How do I give the new owner the ability to use the system?
Connectez-vous pour répondre Voir 1 réponse(s)

12/11/2024

 Toyota Max (130Pts.)

0

Remote start works but can’t unlock/lock the doors

Hi, on my 2014 toyota yaris, everything was working fine up to a few months ago, but now once remote started , the doors won’t lock/unlock and the lights are flashing on the dash but nothing happens. When engine shut down door lock/unlock fine without engine running. I think it is a fsa-206.
Connectez-vous pour répondre Voir 1 réponse(s)

19/08/2024

 Toyota Erich Finley (160Pts.)

0

2022 Toyota Tundra has a cruise control malfunction message on the dash after install.

This vehicle has an EVO one with a toy16 installed.
Connectez-vous pour répondre Voir 1 réponse(s)

05/08/2024

 Toyota htndfw (180Pts.)

0

Evo ONE with CARLINK ASCL6 and T harness in a 2022 tundra locks not working via app

Everything programmed and working minus the locks via the CARLINK app. The parking lights flash and mirrors start to fold in during lock but nothing from the lock. Several ofthers are having the same exact issue Any help would be awesome. Thanks -B
Connectez-vous pour répondre Voir 1 réponse(s)

27/04/2024

 Toyota Ahmad Atlas (190Pts.)

1

2023 - 2024 Toyota Camry shutdown when door opened

Many users complained about this issue " engine shutdown when door opened ". The question: 1- did you update the firmware to resolve this issue for evo rs toy13 kit ? 2- did you add more options for engine shutdown duration (for example 10 minutes)? 3- does your device have security to protect against stealing the car without key - for example engine will shutdown when gear shifted and key not detected?
Connectez-vous pour répondre Voir 1 réponse(s)

13/04/2024

 Toyota Christian Gomez (190Pts.)

0

MyCar will not start 2013 Toyota sienna! Tried everything!!

I have looked at all the question and answers with no luck. I update the firmware on the Evo-one, re-programmed every way possible with different firmware’s, re-programmed the mycar module, I’ve used with and without the little harness that comes with the mycar module, see if the Evo receives a lock/unlock signal while on (nothing), checked if the module is plugged in the right slot. I send the signal from the mycar app, turns green and then red for every option. The app shows signal, battery voltage, gps location, but it won’t accept any command. Please help!! (Can it be a defective device?) It worked before and all of a sudden stopped working.
Connectez-vous pour répondre Voir 1 réponse(s)

21/12/2023

 Toyota Cordellf88 (130Pts.)

0

My remote stopped working

My 2007 tundra I bought used has the RF642W remote and the batteries died, I got them replaced at visions and it just doesn’t work anymore at all. Went back got them replaced again and it worked for about 5 or 6 lock/unlocks then quit again
Connectez-vous pour répondre Voir 1 réponse(s)

25/11/2023

 Toyota Mehmet emin kaya (160Pts.)

0

Transponder

Hello

1-) I have two black car keys, one of which is a 3-button remote. Without transponder  Toyota Yaris 2007. Which module should I install? with keyless or without keyless?

2-) Is there a manual on how exactly I should do the wiring since there is no transponder in this vehicle?

Connectez-vous pour répondre Voir 1 réponse(s)

05/11/2023

 Toyota Devin J (390Pts.)

0

Rf kit not working

Hey guys, So I just installed evo all on a 2018 rav4 push to start with a t harness. 3x lock is working but when I try the rf kit (rfk942) i dont get any response. I paired the remotes correctly…I got the 1x blue light flash confirmation while pairing. Is there something I need to do in the evo all program options? Also, if I change the options, do I need to program the evo all to the vehicle again?
Connectez-vous pour répondre Voir 2 réponse(s)

05/11/2023

 Toyota Devin J (390Pts.)

0

Rf kit not working

Hey guys, So I just installed evo all on a 2018 rav4 push to start with a t harness. 3x lock is working but when I try the rf kit (rfk942) i dont get any response. I paired the remotes correctly…I got the 1x blue light flash confirmation while pairing. Is there something I need to do in the evo all program options? Also, if I change the options, do I need to program the evo all to the vehicle again?
Connectez-vous pour répondre Voir 2 réponse(s)

19/10/2023

 Toyota Jossue (130Pts.)

0

2005 Toyota Tacoma without Transponder key amplifier

I have a 2005 toyota tacoma without a transponder key amplifier, the installation guide said that I should connect the A10 terminal to Rx and the T20 terminal to Tx, but I do not have these cables, because I do not have the 7-pin connector of the transponder, where I should connect them ? What I see is that the guide for a 2010 Toyota Tacoma with type G key is very similar to the 2005 that I have, even down to the ignition cable colors. what should I do? With which diagram should I connect my remote starter?
Connectez-vous pour répondre Voir 2 réponse(s)

19/10/2023

 Toyota Jossue (130Pts.)

0

2005 Toyota Tacoma without Transponder key amplifier

I have a 2005 toyota tacoma without a transponder key amplifier, the installation guide said that I should connect the A10 terminal to Rx and the T20 terminal to Tx, but I do not have these cables, because I do not have the 7-pin connector of the transponder, where I should connect them ? What I see is that the guide for a 2010 Toyota Tacoma with type G key is very similar to the 2005 that I have, even down to the ignition cable colors. what should I do? With which diagram should I connect my remote starter?
Connectez-vous pour répondre Voir 2 réponse(s)

05/10/2023

 Toyota Faisal Alruwaili (180Pts.)

0

Car stay on 2nd switch dont turn on

i installed evo all and rm942 on toyota camry hybrid 2020 but when i remote start the car it stay on ignition but dont start and engine and steering lights turn on even the ac which is most important dont work and i cant control the car lock and unlock with my cars remote and the doors wont lock after 20
Connectez-vous pour répondre Voir 1 réponse(s)

03/10/2023

 Toyota G M (16110Pts.)

0

2023 TOYOTA CAMRY

I installed evo-one (standalone) on a 2023 Camry (euro Key). The connection diagram and programming were the same as for 2020. In the manager I indicated 2019-2023 RAV4 88/20. Everything works and the owner left happy. But 32-3(DK.Blue (GWR) Shut Down After) I think I forgot to choose. And what does 32-3 do? Can you check whether, I indicated it or not? 002B04070335
Connectez-vous pour répondre Voir 1 réponse(s)

01/10/2023

 Toyota zsolt deak (280Pts.)

0

2001 Toyota Highlander tach signal problem

I just installed an evo one in a 2001 Highlander. Vehicle runs for about 8 seconds then shuts down and flashes the parking lights four times which means no tach signal. I have programmed the module to tachless. I set tachless sensitivity -3 because starter did grind with default setting. I have reflashed the module a couple of times and double triple checked all my wiring what am i missing. Why would it flash no tach signal if I have it set to tachless mode option 20 selection 2. Please help I have no idea where to go from here Toyota Highlander MFG date: 01/01 Evo one SN: 002B04 321003
Connectez-vous pour répondre Voir 1 réponse(s)

11/09/2023

 Toyota Tacoguy (130Pts.)

0

Ex-One was just working, now it doesn't, and won't program.

Bought a 2015 Tacoma where the Ex-one didn't work. I diagnosed as a split wire, repaired the wire, programmed the fobs, and got it to work. On and Off, Door Lock and everything worked. Then I unplugged it to run it through my dash, and once everything was back together, now nothing works. I can't even press the valet/programming button to enter programming mode. When I turn the key in the ignition, the yellow light comes on, but that's it. I have tried touching a paperclip to both valet switch terminals to check if it's the button that is malfunctioning but the red light still never goes on. What would cause the whole box to suddenly stop working?? Again, I try to press the valet button, and the red light never comes on to progress through programming mode. Is there a button combination on the fobs? Or a factory reset on the receiver that I can push with a pin? Have I accidentally put it into "valet mode" with a button combination? I do not have the manual because I bought the truck used, and there is no support on this website, and the Fortin troubleshooting app seems to be an incomplete app, where most buttons don't work, and on one screen where it asks me to choose a diagram, the only options are "yes" and "no"...
Connectez-vous pour répondre Voir 1 réponse(s)

08/09/2023

 Toyota MUSTAFA ADNAN (840Pts.)

0

1-way RF kit with 2 4-button remotes very short range

RF kit 441 was programmed on Camry 2020. It was successful, but it is very short range, only 25 meters. What is the reason?

https://photos.app.goo.gl/JRRxv1NiZcJb6nNY9

Connectez-vous pour répondre Voir 1 réponse(s)

04/09/2023

 Toyota MUSTAFA ADNAN (840Pts.)

0

Fortin 441 long range remote start

eHello, gentlemen, one all evo was installed, but the long range remote was not programmed. I followed the instructions to no avail.. The car is a 2020 Camry Hybrid.

I need your support

https://photos.app.goo.gl/fqCaUrBN5Cd7UNXU9

Connectez-vous pour répondre Voir 1 réponse(s)

20/06/2023

 Toyota Mat Harris (130Pts.)

0

Highlander factory remote start

Will my factory remote start still work when using the Toyota app on my phone?
Connectez-vous pour répondre Voir 1 réponse(s)

09/05/2023

 Toyota Ralph Romero (130Pts.)

0

False confirmation from RFK942 remote

Recently installed an evo all and the RFK 942 in my 2021 Corolla. The OEM key fob works fine when remote starting (lock, unlock, lock), but its not the same for the RF kit. When I press and hold the start button it beeps and flashes green indicating a successful start, however the car doesn’t actually start. When I try it for the second or third time that's when it starts. I am just at my window about 10 meters away from the vehicle. Anyone else have this problem?
Connectez-vous pour répondre Voir 1 réponse(s)

27/03/2023

 Toyota brandon luu (160Pts.)

0

2017 Sequoia Courtesy Light interior and exterior not work during remote starts

2017 Toyota sequoia oem alarm. H-key. evo-one with tharness(THAR-ONE-Toy7) flashed to latest firmware. rf642w remote Option D2 enabled and D5 disabled. Truck will remote starts normal. It would unlock/disarm, starts, lock/arm. I go to unlock using 2way remote and the interior and exterior courtesy lights does NOT turn ON. But if the truck was not remote started, the courtesy lights will turn on when unlock with remote. not exactly sure why or how to remedy this issue or if it can be fix? thank you
Connectez-vous pour répondre Voir 1 réponse(s)

06/03/2023

 Toyota Michael Cordivari (130Pts.)

0

Do I really need to cut factory wiring harness in 2021 Highlander Hybrid even with THAR-TOY13?

I am in the process of installing an EVO-ALL into a Toyota Highlander Hybrid (2021). I was under the impression the THAR-TOY13 would make this process plug and play as it did in a previous install (2017 Mazda CX-9), however the instructions say to cut Telematics pin #33 and splice a wire to each end, plus tie into pin #4 (starter) for connection A16. All 3 other T-harness connectdions have been made, do I need to splice? I may abandon this remote start setup if so since the car has an extended Toyota warranty to 100k miles that could be voided if wires are cut.
Connectez-vous pour répondre Voir 1 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer