English
Mon compte Créer un compte
English
EVO-START Wirecolor Fortin Microphones

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

29/10/2025

 Audi kosuke chiba (160Pts.)

0

An error message appears after starting the engine.

Installed the EVO-ALL & RFK942 combination remote starter on a 2015 Audi A6 C7 model.

Using the RFK942, I was able to remotely start the vehicle. However, about 20 seconds after the engine started, an error message appeared.

After that, I could no longer use the RFK942 to stop the engine.

It is possible to stop the engine by getting into the vehicle and using the start/stop button.

What could be causing this issue?

Is the EVO-ALL configuration incorrect?

I would appreciate any solutions.

Connectez-vous pour répondre Voir 1 réponse(s)

23/10/2025

 Audi Artem Tkachenko (190Pts.)

0

What is the complete list of parts needed to install a remote engine start?

Hello Please write a complete list of what is needed for self-connection, programming and setting up remote engine start from OEM key fob using Evo-All VWT1 unit on AUDI S3 8V 2015 with start button? I can't understand whether I need only R-link or only TB-VW or do I need both of these units, and what is needed to program the immobilizer bypass so as not to leave the key in the car? And do I need a transponder? So that I can order everything at once and not have to order the missing parts to Ukraine again and only then figure out how to install it using the instructions :)
Connectez-vous pour répondre Voir 1 réponse(s)

23/10/2025

 Audi Artem Tkachenko (190Pts.)

0

How to order Flashlink Updater?

Hello, please tell me how to order Flashlink Updater from you? I don't have an add to cart button
Connectez-vous pour répondre Voir 1 réponse(s)

21/10/2025

 Audi Artem Tkachenko (190Pts.)

0

Що потрібно для встановлення Evo-All vwt1?

Hello, tell me, do I need any of these products R-LINK, FLASHLINK MOBILE, FLASHLINK UPDATER, TB-VW to install Evo-All vwt1 on Audi S3 8V 2015 so that remote engine start from the native key works? Do I need to flash the already installed Evo-All unit, or can I just buy the Fortin Evo-All VWT1 unit, install it on the car and everything will work right away? Please tell me what is needed to install remote engine start from the native key so that I can buy it all right away? because I will have friends who will send orders to Ukraine :)
Connectez-vous pour répondre Voir 1 réponse(s)

28/07/2025

 Audi G M (17970Pts.)

0

2011 audi a8

Hello. Does remote start with 3x-Lock work or not, with instruction #79791?
Connectez-vous pour répondre Voir 1 réponse(s)

06/04/2025

 Audi Andrew Jackson (130Pts.)

0

Setup for 2017 Audi Q5 B8.5 2.0 TDI Ultra CNHA

Neither THAR-AUD1 nor THAR-AUD2 lists the 2017 TDI Key port as compatible;  however the EVO-ONE lists Q5 2017 as compatible.  I have a 2017 Audi Q5 B8.5 2.0 TDI Ultra , automatic transmission with CNHA engine code (sold Outside US)  and I would like to buy a EVO-ONE with the correct harness for my vehicle. 

    Do I have to buy a THAR-AUD1 or THAR-AUD2 harness separate to the EVO-ONE for 2017 Audi Q5 B8.5 2.0 TDI Ultra, automatic transmission with CNHA engine code ? If so,  Which do i Buy,  THAR-AUD1 or THAR-AUD2 for 2017 Audi Q5 B8.5 2.0 TDI Ultra, automatic transmission with CNHA engine code?Will I have to sacrifice a key? 

Connectez-vous pour répondre Voir 1 réponse(s)

09/01/2025

 Audi Mark.manuel01@gmail.com (130Pts.)

0

What’s needed? 2017 Audi S3 PP DSG Virtual cockpit

As title states what do I need to order to install remote start capabilities. Which system EvoRS, Evo One, T-harness AUD1 or 2, bypass modules, etc. Thanks in advance!
Connectez-vous pour répondre Voir 1 réponse(s)

19/11/2024

 Audi Kcamacho (470Pts.)

0

Why do doors show open on Evo start app? Evo one

Starter seems to be working properly and starts when using factory remote 3 clicks with sacrificial key inside the vehicle. The app is showing voltage and temperature from the vehicle but it also shows that all 4 doors are red as if they are open.  Start function and lock/unlock work but I cannot stop the engine from the app screen.  Am I missing something? 

Thanks.<!--/data/user/0/com.samsung.android.app.notes/files/clipdata/clipdata_content_241119_181735_746.sdocx-->

Connectez-vous pour répondre Voir 1 réponse(s)

07/03/2024

 Audi Craig Hanby2 (230Pts.)

0

2013 Audi A7 Wont Start, key not recognised

I'm currently using an evo one SN: 002B04 079929 I'm trying to program this for an audi a7 2013. I've upgraded the correct firmware as per the manual however i'm getting an issue when attempting to remote start. It shows on the dash key not detected every time. I've done this 3 times now and the 3rd time the Decryptor limit has been reached. Can you advise and then reset please? The programming went fine, all the lights appeared as shown. If i leave the key in the car and remote start it, its fine. but if i do it outside the vehicle it displays key not recognised. Thanks
Connectez-vous pour répondre Voir 6 réponse(s)

07/03/2024

 Audi Craig Hanby2 (230Pts.)

0

2013 Audi A7 Wont Start, key not recognised

I'm currently using an evo one SN: 002B04 079929 I'm trying to program this for an audi a7 2013. I've upgraded the correct firmware as per the manual however i'm getting an issue when attempting to remote start. It shows on the dash key not detected every time. I've done this 3 times now and the 3rd time the Decryptor limit has been reached. Can you advise and then reset please? The programming went fine, all the lights appeared as shown. If i leave the key in the car and remote start it, its fine. but if i do it outside the vehicle it displays key not recognised. Thanks
Connectez-vous pour répondre Voir 6 réponse(s)

07/03/2024

 Audi Craig Hanby2 (230Pts.)

0

2013 Audi A7 Wont Start, key not recognised

I'm currently using an evo one SN: 002B04 079929 I'm trying to program this for an audi a7 2013. I've upgraded the correct firmware as per the manual however i'm getting an issue when attempting to remote start. It shows on the dash key not detected every time. I've done this 3 times now and the 3rd time the Decryptor limit has been reached. Can you advise and then reset please? The programming went fine, all the lights appeared as shown. If i leave the key in the car and remote start it, its fine. but if i do it outside the vehicle it displays key not recognised. Thanks
Connectez-vous pour répondre Voir 6 réponse(s)

07/03/2024

 Audi Craig Hanby2 (230Pts.)

0

2013 Audi A7 Wont Start, key not recognised

I'm currently using an evo one SN: 002B04 079929 I'm trying to program this for an audi a7 2013. I've upgraded the correct firmware as per the manual however i'm getting an issue when attempting to remote start. It shows on the dash key not detected every time. I've done this 3 times now and the 3rd time the Decryptor limit has been reached. Can you advise and then reset please? The programming went fine, all the lights appeared as shown. If i leave the key in the car and remote start it, its fine. but if i do it outside the vehicle it displays key not recognised. Thanks
Connectez-vous pour répondre Voir 6 réponse(s)

07/03/2024

 Audi Craig Hanby2 (230Pts.)

0

2013 Audi A7 Wont Start, key not recognised

I'm currently using an evo one SN: 002B04 079929 I'm trying to program this for an audi a7 2013. I've upgraded the correct firmware as per the manual however i'm getting an issue when attempting to remote start. It shows on the dash key not detected every time. I've done this 3 times now and the 3rd time the Decryptor limit has been reached. Can you advise and then reset please? The programming went fine, all the lights appeared as shown. If i leave the key in the car and remote start it, its fine. but if i do it outside the vehicle it displays key not recognised. Thanks
Connectez-vous pour répondre Voir 6 réponse(s)

16/10/2024

 Audi Marinel Rosca2 (130Pts.)

0

Fit to my car

Hi which device fit to my car Audi A6 C7 3.0TDI 2012?
Connectez-vous pour répondre Voir 1 réponse(s)

11/08/2024

 Audi Alexgonzalez1313 (130Pts.)

0

What system do i need to buy to remote start my 2013 audi q7 tdi

What system do i need i would like to use my factory remote.
Connectez-vous pour répondre Voir 1 réponse(s)

19/02/2024

 Audi Mursini (180Pts.)

0

2015 audi a3, setup and programming complete- no start and no lights on EVO-vwt6

After successfully programming the unit with flash updater and r-link, and a successful d-cryptor session, I reinstalled the unit, and hit the lock button 3 times, and i got nothing. I noted that there are no lights on the unit after all connections are made, with the 4 pin black connector first, and all other connections followed.
Connectez-vous pour répondre Voir 1 réponse(s)

07/03/2024

 Audi Craig Hanby2 (230Pts.)

0

2013 Audi A7 Wont Start, key not recognised

I'm currently using an evo one SN: 002B04 079929 I'm trying to program this for an audi a7 2013. I've upgraded the correct firmware as per the manual however i'm getting an issue when attempting to remote start. It shows on the dash key not detected every time. I've done this 3 times now and the 3rd time the Decryptor limit has been reached. Can you advise and then reset please? The programming went fine, all the lights appeared as shown. If i leave the key in the car and remote start it, its fine. but if i do it outside the vehicle it displays key not recognised. Thanks
Connectez-vous pour répondre Voir 6 réponse(s)

29/02/2024

 Audi Christopher Fisher (130Pts.)

0

Adding remote start via app to my EVO RS remote start

If I have the EVO RS installed in my 2020 Audi S6, is there a module that I can add that would allow me to remote start from an app?
Connectez-vous pour répondre Voir 1 réponse(s)

29/01/2024

 Audi JW (190Pts.)

0

Reason why turned off after remote start

After installing the Lock x3 remote starter and I checked work well. also I flashed the engine to turn off after 15 minutes. But there are situations where the engine turns off when I open the driver's door after starting the remote start. Even though it hasn't been 15 minutes.

It's happens sometimes. What's the problem?

Connectez-vous pour répondre Voir 1 réponse(s)

14/01/2024

 Audi cmoran827@gmail.com (210Pts.)

0

2012 Audi A7 won't start

2012 Audi A7 using Evo One. The entire setup was successful, I was able to program the remote. After install, lock3x did nothing. Looking through Remote Starter options in flashlink, and "System Control by OEM remote" was disabled by default. Ok. Set to lock3x. Reinstalled, now pressing the button turns the ignition on, but does not start vehicle. It does its starting attempt, then turns off and relocks itself. What am I missing here? I'm sure there are other options that I need to change that were not shown in the instructions. Any help would be great.
Connectez-vous pour répondre Voir 1 réponse(s)

12/01/2024

 Audi Dsk (140Pts.)

1

EVO ALL - 2012 Audi A4 Step 7 flashes red 3 times

I am in the process of installing this and I get to step 7 and it is supposed to be solid red then in step 8 red and yellow alternating. At step 7 after Blue red yellow alternate it goes to 3 red flashes over and over. What could be causing this?
Connectez-vous pour répondre Voir 0 réponse(s)

29/12/2023

 Audi JW (190Pts.)

0

THAR-AUD2 & Evo-All, How to Program

I just want to use the remote start function of lock button*3.
I have an Evo-All module and a Thar-Aud2 harness.
I connected this harness to the cable in the trunk side while looking at the installation manual, and I connected the extra remote control key.
And I connected the black connector while pressing the module's program button, but the lights on the all LED are flashing blue, red, and green. It's the same when I take my hands off.

Even if I reconnect all the connectors, the same thing happens.
The program doesn't work at all. What's the problem?
Do I not have to use a black connector to just use the lock button*3?

Please help me

Connectez-vous pour répondre Voir 1 réponse(s)

10/10/2023

 Audi phap truong (250Pts.)

0

2014 Audi RS7 EVO ONE with Carlink ASCL6 4G

What remote start firmware should I used if I am adding a ascl6 carlink to my Evo-One?
Connectez-vous pour répondre Voir 1 réponse(s)

10/10/2023

 Audi exhango (160Pts.)

0

2017 SQ5 Evo-All do not run

Hi, I have install Fortin Evo-audt1 on my audi sq5 2017 but doesn't work. I have connect foot brake wire, Can H & Can L under steering column also I tried under hood clutch and harness on key port. I did the program but on the 8th step doesn't flash red and yellow light, only 3x red light. I try to remote start but nothing happen. if i put the key on key port the remote starter works. SN 001A07 481140. VIN:WA1CCAFP3HA009841. Can you help what can I do?
Connectez-vous pour répondre Voir 1 réponse(s)

22/02/2023

 Audi G M (17970Pts.)

0

Trigger for remote start

Does the trigger for remote start on the evo-one also come from the yellow-black wire? 38.3
Connectez-vous pour répondre Voir 1 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer