English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

04/10/2018

 Ram Elizabeth Kingston (160Pts.)

0

2014 Ram 1500 crimestopper revo 1.1 hangs on yellow when programming remote

installing a revo 1.1 remote starter on my Fortin Evo All unit chrt6 on my 2014 ram 1500. when programming the remote units i unplug the power cable. hold program button and plug power cable back in. i get a solid red and solid blue. i press the program button and hold until the blue and red lights flash out and come back on. I put the key in the ignition and turn to run position i get a solid yellow. red and blue are still lit. when i push the button on the remote unit to pair to module the red and blue light are suppose to blink to acknowledge the remote unit has been programmed. on my unit the red and blue light go out and only the yellow light remains on. firmware 74.37. In my flash link setting under data protocols everything is greyed out i cannot select F2
Connectez-vous pour répondre Voir 2 réponse(s)

04/10/2018

 Ram Elizabeth Kingston (160Pts.)

0

2014 Ram 1500 crimestopper revo 1.1 hangs on yellow when programming remote

installing a revo 1.1 remote starter on my Fortin Evo All unit chrt6 on my 2014 ram 1500. when programming the remote units i unplug the power cable. hold program button and plug power cable back in. i get a solid red and solid blue. i press the program button and hold until the blue and red lights flash out and come back on. I put the key in the ignition and turn to run position i get a solid yellow. red and blue are still lit. when i push the button on the remote unit to pair to module the red and blue light are suppose to blink to acknowledge the remote unit has been programmed. on my unit the red and blue light go out and only the yellow light remains on. firmware 74.37. In my flash link setting under data protocols everything is greyed out i cannot select F2
Connectez-vous pour répondre Voir 2 réponse(s)

19/05/2018

 Kia Marc Gumulka (210Pts.)

0

Need help programming REVO 1.1 to EVO-ONE

 

Hello,   I really need some assistance on the following.   I have been trying to get this REVO 1.1 to program to the EVO-ONE for the last two days. I have followed the instructions very closely. The only issue I potentially see is, and the instructions are unclear on this, do I need to use the power adapter?   My EVO-ONE was installed without a T-Harness, the guide states. "The power connections are only needed for the EVO-ALL and ADS-ALCA integration modules. The EVO-ONE will not require these connections." then later, in the same paragraph the guide states "If you are NOT using a T-Harness, then you WILL need to connect the power and ground wires."   So, do I need the power adapter, or not?   I can't get the REVO 1.1 to program using the steps in the guide. I turn the ignition to ON, I see the yellow LED turn on, on the EVO-ONE module. From there, I hold the valet switch until I can see the red LED turns on and flashes rapidly, and then press the valet switch 5 times, and using the parking lights to confirm each press, followed by pressing the brake one time.   Afterwards, I hold the remote button (the only button) for up to 3 seconds as stated in the guide, but I never see the red LED flash to confirm programming, followed by pressing the brake pedal, and turning off the vehicle. I continued with the steps in case I missed the red LED flash.   This install is on a KIA Soul 2016 - standard key - using the latest firmware for both the module (76.39) and the remote start (1.29).   I made sure to select Fortin2 on the remote start settings in the software as well.

If anything, I will call support on Monday, but I can't believe that I can't seem to get an answer on this anywhere.

I have also tried downgrading the firmware to 1.16, but that didn't work either - I was not even able to get the module to go into programming mode after that.


EDIT:
Here is the answer for anyone that needs it!
 

The guide leaves out information about having to select which wires were set up on the vehicle - somewhat odd to leave the information off entirely...
 

I have attached a link of a screenshot to the software option, these options should have been included within one of the steps shown on the installation instruction documentation.

Connectez-vous pour répondre Voir 1 réponse(s)

12/11/2017

 Chevrolet Ariel Taveras (630Pts.)

0

RF kit Revo 1.1 with Evo All

I just installed an evo all with standalone function to a 2014 Chevy Equinox and added a REVO 1.1 RF kit. The rf kit would start, but once started and i press the remote again it wouldnt unlock the doors like it says it does the crimestopper website. I did select the crimestopper option in the RF kit section while programing the module. Is there another option that i have to enable for it to work?
Connectez-vous pour répondre Voir 1 réponse(s)

21/12/2014

 Ford raylech (490Pts.)

0

Crimestopper REVO-1 with EVO-ALL

I have EVO-ALL installed with THAR and programmed and trying to add REVO-1 RF Kit....cant program remotes....does separate 12V fused power need to be connected to the coupler board (youtube video for this setup on 2104-2015 Ford Escape shows only the dataplug connection to the antenna board)
Connectez-vous pour répondre Voir 1 réponse(s)

07/02/2015

 Dodge Dwight Smith (350Pts.)

1

Why does the Starter Solenoid chatter when only using the REVO-1 RF kit?

I have a 2010 Dodge Ram 1500 with the Evo all and the T harness. Along with the standalone 3x factory remote start, i added the REVO-1 RF Kit. Everthing works perfectly fine until the outside temperature drops down to probably 20 to 30 degrees F and colder. If the truck has set for a while, using the Revo, the solenoid will chatter for several seconds before it will eventually start. Now if the truck was just running and shut off or recently running. The second start attempt using the Revo, the truck will start no problem and continue to until it sets awhile in the cold. Using the factory 3x remote, no issues no matter the temperature. The REVO also will work just fine when temperatures start to rise.
Connectez-vous pour répondre Voir 1 réponse(s)

04/02/2015

 Dodge Dwight Smith (350Pts.)

1

What options need to be enabled/disabled when using REVO-1?

for a 2010 Dodge Ram 1500
Connectez-vous pour répondre Voir 1 réponse(s)

25/01/2015

 Honda Vincent Ma (520Pts.)

0

RF kit for EVO-ONE

I have intalled the REVO1 RF kit for my car to get extend range and one button remote start. But, it is not good enough for me. Do any RF kits have good extend range and 2 ways remote start? Any recomandations?
Connectez-vous pour répondre Voir 1 réponse(s)

25/01/2015

 Honda Vincent Ma (520Pts.)

0

REVO1 RF kit, unlock car

I have intalled Evo-One and my OEM remote and REVO1 remotes can start my car. I just wanna know, can Revo1 remotes unlock car? Because, I click the button by REVO1 remote, it will start my car. When I click the button again, it will shut my car off. Can REVO1 remotes unlock car? Or should I buy another REVO4 kit?
Connectez-vous pour répondre Voir 1 réponse(s)

07/01/2015

 Dodge Dwight Smith (350Pts.)

0

2010 Dodge Ram 1500 gas - starter cut in/out while cranking

I installed a crimestopper Revo-1 with the standalone evo all remote start. when using the Revo remote, it makes an awful noise while cranking,the truck eventually starts. it doesn't seem to happen when using factory remote 3x.
Connectez-vous pour répondre Voir 1 réponse(s)

17/12/2014

 Bypass MarkC (1850Pts.)

0

EVO-ONE function programming with remote transmitters

In the Quick Install Guide I see that function programming is done with the remote transmitter, to select Mode 1-6. Select Mode 1 with lock button, Mode 2 with unlock button, etc. Very straight-forward. But what happens if I use a compatible RF unit like the Crimestopper Revo 1, that has only a 1 button remote? How do I handle function programming if I need to select Mode 2-6?
Connectez-vous pour répondre Voir 1 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer