English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

02/12/2023

 Chevrolet Denis Hamel (130Pts.)

0

2020 Trax

2020 trax, using the GMT-1 All hooked up, All programed, reconnected to the car and will not work. No lights come on, Red,Yellow, or Blue. Turn the ignition on with the key and get a yellow light.
Connectez-vous pour répondre Voir 1 réponse(s)

14/11/2021

 Chevrolet R & P Electronics (280Pts.)

0

2019 Chevy Trax Won't RStart after install

So we have installed a Evo All in this car, Using it as a stand alone RS, The Car will light up everything after 3X on factory remote, but then the dash goes dead, with a CEL light (radio playing) Turns off.... EVO ALL tries agian, and fails... 4 Red light flash on unit... Checked my cables... Everything hooked up correct - Hood Disabled in programing, (Parking lights NOT hooked up at the moment) Removed the flash, and tried to reflash a couple times, and ended up locking myself out (I need cleared please Fortin) Any advice here please help out... Thank you
Connectez-vous pour répondre Voir 1 réponse(s)

29/12/2020

 Chevrolet Ealouise Luke (130Pts.)

0

doors won't unlock with remote after remote start

2017 chevy trax
Connectez-vous pour répondre Voir 1 réponse(s)

23/12/2020

 Chevrolet brad boyd (130Pts.)

0

evo all 2015 chevy trax step 4 yellow only blinks 4 times then goes yellow and red solid

teck support says the brown wire is not making a good connection so i checked and everthing is making good contact and from the obd2 port terminal one (green wire i am curenly plugged rite into it to make sure that is not the issue. checked with meter and the connection is reading .5 of an ohm. so that is not an issue any more if it was. just seeing if anyone know where to go from here thanks
Connectez-vous pour répondre Voir 2 réponse(s)

23/12/2020

 Chevrolet brad boyd (130Pts.)

0

evo all 2015 chevy trax step 4 yellow only blinks 4 times then goes yellow and red solid

teck support says the brown wire is not making a good connection so i checked and everthing is making good contact and from the obd2 port terminal one (green wire i am curenly plugged rite into it to make sure that is not the issue. checked with meter and the connection is reading .5 of an ohm. so that is not an issue any more if it was. just seeing if anyone know where to go from here thanks
Connectez-vous pour répondre Voir 2 réponse(s)

08/01/2020

 Chevrolet William Gorzelsky (130Pts.)

0

Solid Red LED immediately after plugging in Data-Link Wire

I have an EVO-ALL unit with T-Harness THAR-GM1. I went through the initial steps for programming, programmed the unit using the Flashlink Manager software. Reinstalled into the car, remote start did not work. Attempted to redo programming. Unit began displaying a solid Red LED. I held in the programming button and inserted the Data-Link wire and it immediately displayed the solid Red LED again. I continued to hold the button in for several minutes and the Red LED remains lit. I then tried to reconnect it to Flashlink Manager, and it detects it. I tried to reinstall the firmware and it installs. I take it back to the car to try programming again, and again i received the solid Red LED immediately. I am at a loss as to what the problem can be.
Connectez-vous pour répondre Voir 1 réponse(s)

09/12/2018

 Chevrolet Martin Cowger (130Pts.)

0

2019 Trax

looking to install the EVO-GMT1 system on a 2019 Trax LS will there be an update or just program as a 2018 being there is no change in the vehicle between 2018 to 2019 ?
Connectez-vous pour répondre Voir 1 réponse(s)

21/11/2016

 Chevrolet John Chamberlin (150Pts.)

0

Chevy Trax 2014 Takes 4 Button Pushes To Start

I have a successfully working install for 2014 Chevy Trax with T harness. Current firmware updated and used the flash updater to customize for the specific car. Enabled the 3 lock button press OEM remote start option in the menu, saved those settings to the unit. Followed the key on/off proceedures to program the unit successfully. For some reason, it takes 4 lock button pushes to get the starter to engage. Sometimes it take 2 sequences of 4 button pushes also. So sorta scratching my head. The unit is presently attached under the dash and I dont have the service number for the unit. If it's critical, I can ge the number however.
Connectez-vous pour répondre Voir 1 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer