Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question

05/12/2022

Ford Gene B (130Pts.)

0

Differentiate between fob and door keypad on ford / lincoln

Is there an option I can activate to tell my Evo All to ignore the input from the door keypad? I would like the fob to be the only option when remote starting the car. Should this not be possible, is there anyway the system can be changed from starting with Lock being pressed three times to starting with Unlock, followed by two lock combination.

0

2020 Colorado RF Kit disrupts Daytime Running Lights

I have a suuccessful installation. Everything works: remote start, lock/unlock, with the OEM key fob (x3 lock remote start) and the RF442 Kit. The only isssue is that when the RF442 is used to either unlock or remote start the vehicle, the DRL's do not function as OEM intended. The DRL's are the low beams with low poer output. With the OEM remote, everything act's normal, however, with the RF Kit, the low beams simply turn on to full brightness (not low power like it should). I have set the parking lights control in the firmware to both on and off, both with the same issue. In addition, the RF Kit does not 'flash' the vehicle lights to confirm lock or unlock and does not turn on parking lights to indicat the vehicle is running (under remote start conditions).

0

2014 Kia Forte EX PTS VIN8 A Couple of Questions

1st I used Guide 24661 for Evo ONE and 68731 for FL4 when installing the EVO One (recommended firmware identified on program screen, its higher than 76.36, i think there are two newer firms but it wont let me click on them, one is a beta ver.) in car to include adding 2-1 amp diodes at PTS. The car is loaded with options, heated front rear, ac front driver seat, nav and tech pack and more. So I connected laptop to FL(ver 4.05 and recomended in program screen) and FL4 to bypass/ RS and logged in, I dont see the toggle in the lower right corner they speak of, instead I can just click on the tab at top of screen and it asks to confirm or cancel(if you changed anything and didnt save) to switch between bypass and RS. Right now 3x locks the car will crank over but no run, my seat moves, Headlights and dash light up, air controls work, and radio comes on then I hear a couple clicks then the car starts to crank but acks like no fuel, What are all the settings I should have on in the bypass and starter options? I think I had to choose 2.4 in order to get it to even crank, What am i missing or need to check 2nd I see the bypass/starter has a programming set of intructions and the FL4 has its own programming setup however when save and loading setup in user interface when all devices are connected together inline, I get a message stating 20.6 will be changed but it was already defaulted with a green thumbs up, also in bypass I get a message that alot will change when those are also already defaulted with a green thumbs up...smh. Question is how do the options 2.Programmable Option and 31.4,5 and 6 work in unison with each other? Side note while creating this I just realized I did nothing with the decrypt after every thing is done with bypass and RS do i need to click send on the decrypt screen, what is the complete steps in order to complete this. Connect laptop-FL4-Bypass/RS, login, choose settings and load(save), then decrypt, then just unplug, then test or...? Update: I dont think i have a decrypt option...

0

Need reset to change options

After using my new Compustar system for a few months now, I have noticed an odd behavior of the system. Sometimes at certain store parking lots when I get out of the vehicle and lock the door with the Compustar remote, I will get a reply back on the remote a few seconds later that the doors have just been unlocked. However, the doors remain locked. This unlock reply is the same reply that occurs when doors are unlocked with the OEM remote. The OEM remote does work with the Fortin and Compustar when locking and unlocking. So I really don't know what is going on. I was going to disable the OEM remote monitoring feature, but found out my unit is locked and needs to be reset. Could you please reset my unit?

0

Corolla 2013 - G-key - Do I need install something else beside the evo-all

I have Corolla 2013 with G-key. I dont have any remote starter installed in the car, do i need to install something else beside the evo-all in the car to be able start the car with the original remote key that i get from toyota?

3

Lock & unlock doesn't work in a 2009 VW Passat

Hello! I tried to match an EVO-ALL module with a Viper 5704 alarm system and I have same problems. I asked the seller to flash the latest firmware version with D2D protocol, but I can

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer