English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

10/12/2024

 Audi quin Soe (130Pts.)

0

Step 11 key programing

2016 audi a3 push to start evo all serial number: 001A07 016953 I flashed the correct software on to unit with the flashlink. I get to step 11 of key bypass-program with r-link, and it says to wait up to 5 mins with solid red light. Then it's supposed to flash yellow, and the flah yellow and red, but the red light just stays lit and never goes past that point. I've tried reseting evo reprogramming to a different firmware, then back to the recommended firmware, but I can never get past that point and have waited up to 15mins. What should I do at this point?
Connectez-vous pour répondre Voir 1 réponse(s)

20/02/2019

 Audi Richard Moose (180Pts.)

0

TMPS error 2015 Audi A3

I installed the Evo one with the T harness on a2015 Audi A3 with a push to start. When starting the vehicle with the remote start or the push button start the vehicle has the following errors: Stabilizer control ECS malfunction, TPMS error, hill assist disabled.
Connectez-vous pour répondre Voir 2 réponse(s)

20/02/2019

 Audi Richard Moose (180Pts.)

0

TMPS error 2015 Audi A3

I installed the Evo one with the T harness on a2015 Audi A3 with a push to start. When starting the vehicle with the remote start or the push button start the vehicle has the following errors: Stabilizer control ECS malfunction, TPMS error, hill assist disabled.
Connectez-vous pour répondre Voir 2 réponse(s)

14/01/2017

 Audi Jason Reetz (130Pts.)

0

Fortin Evo-All 2011 Audi A3

I'm trying to do a standalone installation of the EVO-ALL on a 2011 Audi A3. All of the wires are connected correctly and I made sure they are making a good connection. I held the prgramming button down and the lights started alternating. I relaesed the button when only the blue LED was lit. I then plugged in the 20 pin, connector, followed by the 6 pin connector, followed by the 5 pin connector. The LED remained blue throughout this process. I then turned the ignition to on. The bule LED went out, then started flasing after a few seconds. I turned the ignition off and the blue LED went out. When I press the factory remote 3X to start the vehicle, the lights flash and the dash lights come on, but it doesn't try to start. It does the same thing a second time and then the EVO-ALL turns off. However, if I sit inside the vehicle and press the brake, it will start the car, but it only runs for 1 or 2 seconds before shutting down. On this particular vehicle, although it uses the regular keyed ignition switch, you still have to press the brake to start the vehicle. Is there another connection that needs to be made for this to work properly? Thank you, Jason
Connectez-vous pour répondre Voir 2 réponse(s)

14/01/2017

 Audi Jason Reetz (130Pts.)

0

Fortin Evo-All 2011 Audi A3

I'm trying to do a standalone installation of the EVO-ALL on a 2011 Audi A3. All of the wires are connected correctly and I made sure they are making a good connection. I held the prgramming button down and the lights started alternating. I relaesed the button when only the blue LED was lit. I then plugged in the 20 pin, connector, followed by the 6 pin connector, followed by the 5 pin connector. The LED remained blue throughout this process. I then turned the ignition to on. The bule LED went out, then started flasing after a few seconds. I turned the ignition off and the blue LED went out. When I press the factory remote 3X to start the vehicle, the lights flash and the dash lights come on, but it doesn't try to start. It does the same thing a second time and then the EVO-ALL turns off. However, if I sit inside the vehicle and press the brake, it will start the car, but it only runs for 1 or 2 seconds before shutting down. On this particular vehicle, although it uses the regular keyed ignition switch, you still have to press the brake to start the vehicle. Is there another connection that needs to be made for this to work properly? Thank you, Jason
Connectez-vous pour répondre Voir 2 réponse(s)

08/01/2016

 Audi Luc Ostiguy (940Pts.)

1

Stop working Audi A3 2011

I install evo-all and a remote starter in a 2011 Audi a3. It works fine. 2 days after the remote doesn't work anymore. I tried it and manage to make it works with the key near the cylinder. Can the evo-all loose its key programation ? Can i see what is wrong looking at the colored led on the EVO-ALL. Should i reset it and reprogrammed it? Do i need to plug it back to the flash-link programmer? Thank you
Connectez-vous pour répondre Voir 2 réponse(s)

08/01/2016

 Audi Luc Ostiguy (940Pts.)

1

Stop working Audi A3 2011

I install evo-all and a remote starter in a 2011 Audi a3. It works fine. 2 days after the remote doesn't work anymore. I tried it and manage to make it works with the key near the cylinder. Can the evo-all loose its key programation ? Can i see what is wrong looking at the colored led on the EVO-ALL. Should i reset it and reprogrammed it? Do i need to plug it back to the flash-link programmer? Thank you
Connectez-vous pour répondre Voir 2 réponse(s)

27/12/2015

 Audi Kenny Schaffrick (360Pts.)

0

Evo-all 2006 Audi A3 with CM7200 controller not seeing tach through Data

I am installing a cm7200 starer in a 2003 Audi A3 and am using the data port for connectiong the two units. I cannot find if there are any issues with compatibility between these two units IE, two way data. I can't seem to get tach to program or the unit to go into reservation mode for standards. i am guessing the reservation issue is something to do with the tach issue.
Connectez-vous pour répondre Voir 1 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer